Search Documents

By Torres S. Ricardo, Encina M. Víctor, Segura O. Claudio

INTRODUCTION This paper is a conceptual resume of engineering studies that have been evaluated by the Mine Department related to production planning over the next twenty-five years. These studies have been required principally because: a) The Rio Blanco Mine, property of CODELCO- CHILE, Andina Division, faces an operational problem due to heavy snowfall in winter which enters the surface subsidence area of the cave; later melts and filters into the broken ore creating a product that is difficult to transfer through the orepasses. The phenomenon is especially serious during the spring and has been increasing over the years. This element that complicates extraction will be controlled with the procedures proposed or others that may be determined in the future. b) The mine will increase production in 1985 by 40% . LOCATION The deposit is located in the central region of the Andes Cordillera, at an altitude of approximately 3,600 m above sea level, 50 km to the northeast of Santiago. The main camp is Saladillo (at 1,300 meters above sea level) located 30 km from the mine. Due to its location, the mine is subject to heavy snow storms during the year. On many occasions the road from Saladillo to the mine is closed because of storms and avalanches. For this reason the company has self-sufficient civil facilities near the mine to cover the needs and welfare of the working force. These housing facilities are connected to the mine by underground passages. For the same weather related reason the primary and secondary crushers, and the entire concentrator complex are located underground. GEOLOGIC CHARACTERISTICS Geology Based on the geologic model developed for the Rio Blanco deposit and comparing it with standard models pertaining to copper porphyries, it can be concluded that this deposit is part of the apical sector of a mega deposit and therefore the projections of the Xio Blanco cop per mine are very favorable, both in lateral area and depth. In order to confirm and evaluate these geo- logic features, an extensive drilling program was started at the Rio Blanco deposit. Diamond drill holes were drilled to depth as well as in the areas named "La Americana", "Don Luis" and "Elguin". The area explored by the drill program is 3 km long in a north-south direction and 1.5 km wide in an east-west direction. In some sections the drilling in depth reached the 2,300 m elevation mark. The lowermost level in the mine is at elevation 3,070 m. These new studies have permitted the recognition of the following lithologic units: Andesite Andesite Breccia Granodiorites, Rio Blanco and Cascada Granodiorite Breccia Quartzmonzonite Porphyry Monzodiorites and Latites Tourmaline Breccia Dacite Pipe and Rhyolite marginal ring. The mineralogical study permits the definition of three stages of hypogene and hydroterma1 alteration of importance with a time-altered sequence. These stages correspond to a late hydrothermal stage. The kinds of alteration that have been recognized are: Potasic Alteration Propylitic Alteration

Jan 1, 1981

By L. Ekstrom, J. P. Dismukes

The homogeneity and microstrcture of zone-leveled Ge-Si alloys haw been investigated by sellera1 physical techniques and by metallography as a function of growth rate in the range 3 x 10 1x10 cm-sec', and as a system of alloy composition throughout the system. The temperature gradient at the solid-liquid interface was about 50 deg-cm-' Cellular or dendritic structures char-acteristic of constitutional supercooling were ob-served except at very slow growth rates, which ranged from about 2 x 10 cm -sec for Ge 1 sio alloy to about 2 X 10'5 cm-sec'1 for Ge .sSio.s alloy. Using a simple model similiar to that employed for dilute solid the dependence upon compo-sition over the entire system of the critical growth rate for the onset of constiutional supercooling was calculated, and was .found to he in good agreement with the experimental results. THE recent discovery of the low thermal conductivity of Ge-Si alloys' at high temperatures has revealed that these alloys have high efficiencies for thermoelectric-power generation.', Therefore, a reliable method was needed for the preparation of homogeneous samples required for definitive measurements throughout this alloy system. Due to the low diffusion rates in the solid alloys, the segregated samples obtained by quenching a melt are not readily homogenized by annealing.475 However. isothermal solidification from a melt of constant composition can produce uniform material. Of the available semiconductor crystal-growth procedures, the zone-leveling technique6 applied to a complete solid-solution alloy system by Wang and Alexander' and by others provides a simple method of doing this. In the present work, the homogeneity and microstructure of zone-leveled alloys have been correlated with growth conditions, and the conditions for preparing homogeneous Ge-Si alloys have been established. This has provided insight into the solidification process of alloy semiconductors. EXPERIMENTAL PROCEDURE Sample Preparation. The Ge-Si alloy phase diagram4 shown in Fig. l(a) consists of a complete series of solid solutions. The zone-leveling technique used to prepare most of the samples consists of moving a zone of liquidus composition (C1) through charge material of the corresponding solidus composition (C,), as is illustrated in Figs. l(b) and l(c). To prepare the charge materials, high-purity germanium and silicon were pulverized in a steel hammer mill, cleaned magnetically, and melted together to make uniform chill castings. The zone leveling was carried out in a resistance-heated furnace similar to that of Mitrenin et al.' shown in Fig. 2. However, a few specimens of high silicon content were prepared by the Czochralski technique. The growth rate ranged from 3.5 x X6 to 1.2 X 10~3 cm-sec-'. Temperature gradients in the solid and in the melt were determined by recording the temperature as the molten zone passed over a Pt-Pt 13 pct Rh thermocouple contained in a small

Jan 1, 1965

By R. W. Smashey, B. J. Piearcey

The structure, composition, and morphology of the carbide phases present in the nickel-base superalloy, Mar-M200, hare been determined and three carbide phases observed. The MC carbide is a solidification product, and the M23 Co and M6C carbides are both prod~icts of solid-state precipitation. The identity of each phase usas determined by both X-ray and electron-diffraction techn~ques. Compositions of all three carbides were studied using the electron beam micro-probe analyzer and by unalyszs of electrolytically extracted residues. Optical and electron microscopy were employed in order that the time/temperature -dependent behavior of the carbides might be observed. Supplementary studies were completed on thin foils and oriented single crystals to determine the mor-phology and orientation relationship of each phase with that of the matrix. MAR-M~OO* is a high-temperature, creep-resistant superalloy designed for use in the as-cast condition. The "as-cast" microstructure consists of a solid-solution matrix, referred to as gamma (y), which contains a general, coherent precipitate of the inter-metallic Ni3(A1,Ti) referred to as gamma prime (?). As a result of dendritic segregation during solidification, a degenerate, spherulitic ? -?' eutectic constituent is present at the grain boundaries and the in-terdendritic regions, which is nucleated by the y on the dendrite tips. A primary carbide phase, a solidification product, is also present at the grain boundaries and in the interdendritic areas, and an additional carbide appears at the grain boundaries as a fine discontinuous precipitate. The alloy is particularly susceptible to heat treatment. For example, the mechanical properties of the columnar grained mater- ial are substantially improved by solution heat treatment, followed by an intermediate temperature age. Metallographic examination of heat-treated material reveals, however, that exposure to elevated temperatures has a marked effect on the microstructure of the alloy; in particular, it is observed that precipitation of considerable amounts of various carbide phases occur. The following investigation was carried out to determine the morphology, composition, and behavior of the carbides in Mar-Ma00 as an aid to the determination of their effect on the mechanical properties and stability of the alloy. THE PRIMARY MC CARBIDE The MC carbide phase appears in the interdendritic interstices and the grain boundaries. In directionally solidified Mar-M200 the carbide appears as very small particles in the chilled region, Fig. l(a), whereas in material less affected by the chill, it becomes larger and develops a dendritic morphology, Fig. 1(b). Step polishing of metallographic specimens from this region shows that in directionally solidified material the individual carbide dendrites are connected in a dendritic network within the metallic interdendritic interstices, whereas in material from the chilled region and in conventional Mar-M200 they are discontinuous, isolated dendrites. No orientation relationship exists between the primary carbide and the matrix.

Jan 1, 1968

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method. CONSIDERING the subject alone, this paper would cover only a mechanical treatise of pillar roping. Because the St. Joseph Lead Co. originated the practice, it is proper to give a short introduction to the company. It is also proper to describe pillars and discuss their purpose to justify expending large sums of money to preserve them after the surrounding area has been thoroughly mined. Because the St. Joseph Lead Co. originated the practice of back pinning with wedge bolts, patch plates and channel irons, and the pouring of substitute pillars of concrete, these too, are mentioned. The Southeast Missouri Division of the St. Joseph Lead Co. is the largest lead producer in the United States. About 95 pct of the present producing mines are in St. Francois County, which begins 60 miles south of St. Louis. The entire lead ore production of this county, at the present time, is mined and milled by this company, treatment plant capacity being about 22,000 tons per day. This area is also the oldest, lead having been mined at Mine La Motte, in Madison County, in 1723. Estimated production of all the various companies that have mined here is about 7,000,000 short tons of pig lead. Method of Mining The lead occurs in the ore as galena. Galena is found either in the form of disseminated or solid streaks, of varying thickness. Ore stratum is the Bonne Terre dolomite, which is about 350 ft thick, but almost all the ore is in the lower 100 ft. Ore is mined by room and pillar method in open stopes. These stopes vary in height from 7 ft to 200 ft, depending on the thickness of the pay ore in that spot. Back, or roof, is supported entirely by pillars. In a majority of stopes, after the loose scales are mined down, the back has remained solid for many years (fig. 1). Under ideal conditions pillars are spaced to form an equilateral triangle and are as small and as far apart as the height of the stope and the character of the back will permit. They vary in diameter from 10 ft to 50 ft and are from 18 ft to 50 ft apart, measured from the outer edges. In general, the pillars are approximately 12 ft in diameter, and 25 ft apart. The spacing is very uncertain because of the vagaries of the ore trend, the desire to better support breaks in the back, and the attempt to spot out the thinner ore by not placing one in the core of the ore body. Use of Structural Steel Channels In stopes where the back is bad because the overlying formations are thin with wet, weak and shaly

Jan 1, 1951

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method. CONSIDERING the subject alone, this paper would cover only a mechanical treatise of pillar roping. Because the St. Joseph Lead Co. originated the practice, it is proper to give a short introduction to the company. It is also proper to describe pillars and discuss their purpose to justify expending large sums of money to preserve them after the surrounding area has been thoroughly mined. Because the St. Joseph Lead Co. originated the practice of back pinning with wedge bolts, patch plates and channel irons, and the pouring of substitute pillars of concrete, these too, are mentioned. The Southeast Missouri Division of the St. Joseph Lead Co. is the largest lead producer in the United States. About 95 pct of the present producing mines are in St. Francois County, which begins 60 miles south of St. Louis. The entire lead ore production of this county, at the present time, is mined and milled by this company, treatment plant capacity being about 22,000 tons per day. This area is also the oldest, lead having been mined at Mine La Motte, in Madison County, in 1723. Estimated production of all the various companies that have mined here is about 7,000,000 short tons of pig lead. Method of Mining The lead occurs in the ore as galena. Galena is found either in the form of disseminated or solid streaks, of varying thickness. Ore stratum is the Bonne Terre dolomite, which is about 350 ft thick, but almost all the ore is in the lower 100 ft. Ore is mined by room and pillar method in open stopes. These stopes vary in height from 7 ft to 200 ft, depending on the thickness of the pay ore in that spot. Back, or roof, is supported entirely by pillars. In a majority of stopes, after the loose scales are mined down, the back has remained solid for many years (fig. 1). Under ideal conditions pillars are spaced to form an equilateral triangle and are as small and as far apart as the height of the stope and the character of the back will permit. They vary in diameter from 10 ft to 50 ft and are from 18 ft to 50 ft apart, measured from the outer edges. In general, the pillars are approximately 12 ft in diameter, and 25 ft apart. The spacing is very uncertain because of the vagaries of the ore trend, the desire to better support breaks in the back, and the attempt to spot out the thinner ore by not placing one in the core of the ore body. Use of Structural Steel Channels In stopes where the back is bad because the overlying formations are thin with wet, weak and shaly

Jan 1, 1951

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man's mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the, gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 1, 1950

By R. W. Raymond

The immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages—in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, me Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley's process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. What Did Mr. Gayley Invent? Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley'a first patents. It may be admitted, without such critical analysis, that the possible advantages of removing moisture from the air forced into an iron blast-furnace were recognized and talked about a hun-

Jan 1, 1909

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By George A. Miller

OIL, the abundance of it in the hands of the Allies and the lack of it in the hands of the Axis, played a major role in winning World War II. It bids fair to implement the winning of the peace. In fact the signing of the revised agreement on petroleum between the Government of the United Kingdom of Great Britain and Northern Ireland and the Government of the United States of America on Sept. 24, 1945, may be considered as the first step in establishing a new pattern in foreign relations by our Government. The significance of this agreement on petroleum is that it was arrived at on the part of the United States of America through the advice and consent of the most interested parties, the leaders of the petroleum industry and the Government, distinctly a first step toward unifying the power of business and the strength of the Government, which places us on a par with the British Crown which has always had the advice and counsel of its business leaders in formulating its foreign trade policies. And what is the thing so patently discernible in this new first step toward winning the peace? It is that the petroleum agreement, the first draft of which, signed in Washington on Aug. 8, 1944, almost caused an epidemic of apoplexy among the leaders of the oil industry, represents the desire of the people most concerned with the problems of petroleum both at home and abroad. This new agreement, which will come up before the Senate for ratification this month-hearings will commence in January - derives its "power from the consent of the governed," something about which our forefathers were vitally concerned once upon a time.

Jan 1, 1946

By Richard P. E. Hermsdorf

IN the nonferrous sessions this year, magnesium wiggled its way into a dace of prominence such as it has never before enjoyed. This was evidenced not only by the number of papers presented on that metal but by the attendance at the meetings. The atmosphere permeating these magnesium meetings was similar to that which exists in a family with a new baby. Everybody crowded around to see what it looked like and then wondered whether it would be a success and credit to the family. Well. magnesium appeared to be a vigorous youngster, full of life, and raring to go. A close relative of maenesium named " aluminum, although much more grown up, also attracted much attention. From the activity and spirit in these sessions

Jan 1, 1944

By P. E. Fitzgerald

SOME readjustments in the research programs of most of the oil companics and petroleum engineering schools have been made necessary by the war. The most obvious change has been the conversion from production engineering to problems more closely related to the nation's was effort. Many laboratories now devote much of their time to studies on products to be derived from petroleum. such as synthetic rubber, toluene, and substitutes for critical materials. Others are working to improve motor fuels including high-octane gasoline and the special lubricants required by the wide geographical range of the present conflict. Of great importance is the experience of the geophysicists, who are now devoting a great percentage of their time on instrument research and production or special apparatus required by the armed forces.

Jan 1, 1943

By E. J. KENNEDY

THE annual dinner-dance was held in the large ball room of the Commodore hotel Wednesday evening. A total of 577 were seated at the dinner, over which President Eavenson presided as chairman and toastmaster. In introducing George C. Stone, the James Douglas Medalist, W. R. Ingalls outlined the former's association with the zinc industry. He said, in part In designing and building Palmerton, Stone erected a metallurgical monument and won the title of chief engineer of the New Jersey Zinc Co., with transferal to its New York office in 1900. There lie held forth in dignity, efficiency, and with appreciation until his retirement from active service in 1929. After a few years lie was diverted from the position of chief engineer for his company to the superior one of chief metallurgist and that gave to Stone his next big chance.... This was the conception of a research department and the ability to persuade his directors to adopt it. I shall not pretend to summarize the great things that afterward developed. I shall mention only the institution of the manufacture of lithopone in this country, the charging of the Wetherill furnace with briquets, the mechanicalization of the Wetherills, the accomplishment of continuous distilling, and most recently the introduction of reflux-refining.

Jan 1, 1935

By Joseph W. Richards

ALTHOUGH bad grammar, the above query is probably, at the present moment, good sense. Why was the Institute started and why does it continue to exist? The small group of men who worked out the original idea felt keenly the necessity of mining engineers and metallurgists getting together in order to discuss their professional problems. That necessity still exists but it does not strike the present generation of engineers so keenly because they have always had the Institute: they do not know what it is to be without it. The Institute is a great graduate school of mining and metallurgy. All of its members who have something to say worth saying are the teachers; all the rest may be learners or critics. No university or technical school can match the experience and information which the authors of its papers possess, no institution of learning has a body of potential listeners so extensive and so vitally interested.

Jan 1, 1921

E. E. Olcott, New York City: Prof. Kemp's valuable description of the Lancaster Gap mine is in line with many other able contributions on the origin of mineral deposits that the Institute has lately brought forward. The splendid contribution that Prof.

Jan 1, 1895

By Henry G. Morris

The use of compressed air for the transmission of power has reached so great a development that we find numerous large establishments devoted to the manufacture of machinery for its production and application, and special periodicals published for the dissemination of information on the subject. Moreover, its employment is so general in mining operations that no apology is needed for the presentation to the Institute of such a paper as the present. The admirable articles of Mr. E. A. Rix, published in Conzpressed Air, show a wide range in the mechanical efficiency of air-compressors, varying, under different conditions, from 15 to 60 per cent.; and it is evident that any

Jan 1, 1902

By Walter R. Hibbard, Harold Margolin

DURING preliminary tests on the aging of a Cu-plus 5 pct Ag alloy,' a specimen which had been overaged 24 hr at 550°C was annealed in a nitrogen-hydrogen atmosphere first for 2 hr and then for an additional 28 hr at 600°C. After each anneal the specimen was cooled to room temperature in about ½ hr and X-ray photograms were made. The first film, Fig. la, revealed two sets of copper-base lines, one intense and corresponding to the parameter at 550°C, the other fainter and shifted away from the beam, corresponding to the larger parameter at 600°C (see arrows). The 30-hr film, Fig. lb, revealed the same two sets of copper-base lines with a reversal of intensity. In neither case do the copper lines form a broad band which would be indicative of a range of compositions. This phenomenon is thus a "discontinuous" type of solution. A similar phenomenon was observed in a Ag-rich Cu-Ag alloy.' Finlay and Hibbard9 have suggested that directional rather than random solution of precipitate occurs in some alloys. Conceivably, for Cu-Ag alloys, the matrix-transition-precipitate precipitation sequence is reversible for the re-solution of the precipitate caused by rapidly raising the annealing temperature of an overaged specimen. A copper-base transition structure supersaturated with solute might be formed around the precipitate as it dissolves, thus obviating the necessity for a gradually changing solute composition of the matrix. The solute atoms then might be transferred rapidly and locally from the transition to the matrix phase in the proper amount and at the proper location to obtain directly the new ex- panded solid solution. The theory implies a minimum of diEusion of solute in the matrix (i.e., no significant range of matrix composition) and possibly suggests that the composition of the transition structure will vary with the conditions of re-solution. A transition copper phase found in aged Cu-Ag alloys1 might fulfill this function. Evidence regarding this suggestion could be obtained in Cu-Ag alloys by overaging a specimen until no trace of the expanded copper lattice is present and then subjecting the specimen to a retrogression treatment. Re-appearance of the transition copper phase would confirm the theory. Additional details could be secured by varying both aging and retrogression temperatures. References 'H. Margolin and W. R. Hibbard, Jr.: Effect of Ternary Additions on the Age Hardening of a Copper-Silver Alloy. Trans. AIME (1951) 191, p. 174; Journal of Metals (Feb. 1951) TP 3002E. 2 W. Ageew, M. Hansen, and G. Sachs: Decomposition and Changes in Properties of Super-saturated Silver-Copper Alloys. Ztsch. Physik (1930) 66, p. 350. 3W. L. Finlay and W. R. Hibbard, Jr.: Some Effects of Applied Stresses on Precipitation Phenomena. Trans. AIME (1949) 180, p. 255; Metals Technology (Sept.

Jan 1, 1952

By James E. Little

(Wilkes-Barre Meeting, June, 1911.) OF the several extensive deposits of brown iron-ore in Cuba, including those of Mayari and Moa, that of Mayari was the first to be systematically explored, and was selected as the scene of the first operations in the development of this class of ore. Construction-work, begun in the spring of 1907, involved the building of 16 miles of standard-gauge railroad and two large double-track inclines, the installation of mining-machinery, a nodulizing-plant, power-plant, shops and shipping-facilities, and the dredging of an extensive basin for deep-draught vessels. Unusual weather-conditions delayed the completion of portions of this work so that the entire plant was not in operation until December, 1909. The ore in its natural state contains a very large percentage of water, which increases to some extent with the depth below the surface. Near the surface it is red in color, with somewhat granular structure. The color gradually changes with depth, finally reaching a bright yellow. The consistency also changes towards, the bottom to a clay-like, sticky mass. The relative proportion of red and yellow ore is quite variable; in some places the yellow reaches close to the surface, while in others the red extends almost to the underlying serpentine. Fig. 1 is a map showing the Mayari division of the Spanish-American Iron Co. The ore lies on an irregular plateau about 15 miles long and 5 miles wide at the widest point, entirely covered with pine trees and brush, which grow directly on the ore. The elevation at the northern extremity, which is approached by the railroad, is about 1,700 ft. above sea-level. At the southern end the general elevation is about 2,000 ft. Ore is removed by means of scraper-bucket excavators and steam-shovels, these machines loading into special standard-guage, side-dump steel cars of 100,000 lb. capacity. A short haul

Aug 1, 1911