Search Documents

By Walter R. Hibbard

BACKOFEN' reported recently that "the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [lll.] and [loo] directions aligned parallel to the wire axis." In the introduction, he indicated that this was in contrast to the work of Hibbard,' who reported a single [111] texture after a reduction of 96.4 pct. Unfortunately Backofen stated that this was a reduction in area when actually it was a reduction in diameter, as is clearly stated in the reference. Moreover, the results of Backofen are in complete agreement with the results of Hibbard. Backofen's 97.3 pct reduction in area is an 83.3 pct reduction in diameter, after which he foundadouble [ll11 and[l001texture with the former predominating. Similarly, Hibbard; after an 86 pct reduction in diameter found a double [Ill] and [I001 texture with the former predom- inating. Hibbard, however, when he drew the wire further to 96.4 pct reduction in diameter, found primarily a single [Ill1 texture as illustrated by Fig. 2 of ref. 3. Here also, Hibbard- reported evidences of the [loo] recrystallization texture found by Backofen. It might also be pointed out that Backofen not only drew his wire 97.3 pct reduction in area but also etched them over 99 pct reduction in area from 0.125 to 0.01 in. diam. Hibbard's wires were drawn directly to size. In summary, the deformation texture of cold-drawn copper wire still may be described as primarily a single Clll] texture after a sufficient amount of drawing, such as 96.4 pct reduction in diameter." a

Jan 1, 1952

Striving to do a better job of ad- ministering the letter and spirit of the Federal Coal Mine Health and Safety Act of 1969, the Interior Department recently invited criticism-and got it. The criticisms were voiced on July 1 and 2 at the first of a series of public meetings being held by the Office of Hearings and Appeals at the Department's behest. Later meetings, at which all interested parties are invited to comment, are to be announced in the press and the Federal Register. Persons wishing to participate in the meetings should contact the Director, Office of Hearings and Appeals, 1015 Wilson Blvd., Arlington, Va. 22203. At the first Hearing, USBM Director Elburt F. Osborn outlined the progress his agency has made to date in implementing the law on three fronts: enforcement, education and research. Since the Health and Safety Act became law on December 30. 1969, he said, the Bureau's force of inspectors has grown from a mere 300 to almost 1100, while mine inspections have increased from 10,265 in 1970 to 11,021 for the first six months of 1971. On the educational front. Osborn said, the Bureau now has some 60 instructors who have trained about 50,000 miners in safety procedures since March 30. 1971. Classes at the new Federal Mine Safety Academy for both government and industry personnel begin on September 1, 1971. he added. Health and safety re- search, meanwhile, has been allot- ted $20.1 million for the 1971 Fiscal Year. Of this, $8.1 million is assigned to the Bureau and $12.3 million to contracts with universities and private companies. Admittedly, Osborn said, the mine fatality rate is still unacceptable, hut it was lower in the first half of 1971 than ever before---0.73 per million man hours and 0.31 per million tons of coal.

Jan 1, 1971

By G. H. F. Gardner

The boundary conditions F = 1.0 and 4 = 1.0 (100 per cent) are dictated by the definition of F in the equation 1/F = aFp. These conditions have physical significance as the "limiting conditions" for the observed behavior in systems of dispersed particles. The other boundary conditions, cited by Gardner in his Eq. 3 as applying to this system, have no significance in the systems we studied. Maxwell's equation (Eq. 2) cited in Gardner's comments was developed for and limited to a regular, rather than random, dispersion of spheres which are sufficiently removed from each other so that they do not interfere with current flow about their neighbors. These restrictions also apply to Rayleigh's analysis. The title of Rayleigh's paper cited by Gardner is "On the Influence of Obstacles Arrayed in Rectangular Order upon the Properties of a Medium". He is not discussing randomly dispersed spheres. It might be inferred from Gardner's comments that Rayleigh specifically considered the differential equation (Gardner's Eq. 3). This is not the case. Mathematically, Gardner's Eq. 3 is exactly true for the system to which it applies, however, as both Rayleigh and Maxwell note that their equation for F in terms of F is not for randomly dispersed spheres. At the time we wrote our paper, we were aware of the work of Wyllie and Gregory as cited by Gardner. We cited their work in Ref. 5 of our paper. Our comment on page 287 of the paper about the validity of an m value of 1.3 for spheres with a porosity of 38 per cent remains as our answer to Gardner's question on this point. Our data, at 38 per cent porosity, show that the condition a = 1 and m = 1.3 holds for spheres near 40 per cent porosity.

By Thomas Fraser, H. F. Yancey

The jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed of about — 1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation J?ngstl concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 1, 1925

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By D. P. Koistinen, K. E. Beu

THE application of the integrated intensity X-ray diffraction method to the measurement of retained austenite concentrations in hardened steels has been fully described.'-' In developing this particular method, the assumption was made that the samples used would have flat surfaces which were free from voids and in which austenite was homogeneously distributed. The original calculation procedure' was modified to include the constant factor G which relates the intensity of a given diffraction line to the concentration of the component giving rise to that line. In order to include A (0) in the constant factor G, it was further assumed that the geometrical conditions relating the X-ray beam, camera cylinder, and sample surface were precisely met.V has been demonstrated that these geometrical conditions can be met experimentally without difficulty in many cases;' however, for those samples which have irregular surfaces or where it is impossible to locate the sample in the proper position with respect to the X-ray beam and film cylinder, it is desirable to evaluate experimentally what effect these nonideal conditions have on the reliability of the austenite determination. This note decribes the results of such experiments. SAE 1095 bar stock was used throughout and all samples were heat-treated as follows: 1600°F for 1 hr in a neutral atmosphere, brine quench, and 300°F temper for 30 min. To control heat-treatment conditions as closely as possible, all samples were plated with 0.002 in. copper to protect the immediate surface from the heat-treating atmosphere. After heat treating, the samples were deplated electroly-tically so that only the copper was removed. The heat-treated surfaces thus obtained were nearly as bright and polished as the original surfaces before copper plating although no mechanical work was done on the samples after heat treating.

Jan 1, 1954

By H. S. Geismer

INTRODUCTION. THERE are three general methods available for obtaining commercial brown iron-ore : hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all foreign material to be separated from ores before they are delivered to the furnace, and hand-screened ores can rarely be made to fulfill that requirement. Another argument against hand-screening is, that the waste-pile often contains as much ore as the screen recovers. The operation known as hand-screening consists of throwing the ore-bearing material against a stationary inclined screen of 0.5- to 0.75-in. mesh, similar in construction to the screens employed in sand-pits. The recently-prospected brown-ore deposits of Cuba seem to offer possibilities for hand-screening not possessed by the average American deposit, since these ores are not associated with worthless clays. Washing, and washing and concentrating, may be discussed together, since concentrating is never practical on brown iron-ore, except to treat ores that have already been washed. (Strictly speaking, washing might be classed as concentrating, but it is never so designated by brown-ore men.) The various steps of removing ore-bearing material and converting it into ore suitable for blast-furnace use, may be grouped under five heads: loading for transportation ; transporting ; feeding into the washer; washing; and concentrating. These five subjects will be considered in consecutive order. Each of these successive steps may be accomplished in a number of different ways, the choice depending entirely upon the character of the ore-bearing material to be treated.

Aug 1, 1911

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By James Norman, E. W. Gieseke

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content. it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, [t] the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2, 3 The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. STUDY OF METHOD OF FLOTATION SEPARATION Most of the work on concentration of spodumene was done with rock from near King's Mountain, North Carolina. Rock from two

Jan 1, 1940

By Stewart, J. B.

THE property at which this work was done consists of a large deposit of potash salts occurring in massive beds of rock salt, overlain by 600 ft. of salt-impregnated shales and marls. It is in the Province of Cataluiia, Spain, about 45 miles from the railway station of Mauresa and about a mile south of Suria. In addition to sinking the shaft, the program of construction work laid out by the European owners (not Spaniards) included a single-track narrow-gage railroad from Mauresa to the mine; one large office building and several large shop buildings, all of brick and concrete with steel truss roofs; two extensive benches for the future recovery plant; and a large village of stone dwellings for employees. The pay-roll showed approximately 1200 to 1500 men employed. After two years' operation, ending early in the autumn of 1920, the shaft had been sunk 325 ft. and still had an equal distance to go to reach the potash; all tunnels for the railroad were done and the road-bed $0 per cent completed; only a little more than the foundations were completed for all the large buildings, and the excavations of the benches were about 75 per cent done-while only a fair start had been made upon the employees' village. This was the state of affairs when the European owners decided to offer this property under a one-year option to an American syndicate, providing that they agreed to carry on the entire building program and to sink the shaft as fast as was consistent with the quality of work which they demanded, for they wished the shaft to endure at least 200 years.

Jan 1, 1926

A mine that staggers the imagination is Chuquicamata, the granddaddy of them all. In 1968 production exceeded 300,000 tons of copper. Production began in 1915 and mining proceeded solely on oxide ores until 1953 when the first treatment of sulfides began. Today the company has mined about 1.2 billion tons of all types of material since inception. The accelerating rate of output can be gauged by the comparable 1946 figure of production-to-date which was 350 million tons. No single mine comes close to touching Chuqui for productivity at its high annual metal yield mining only 90,000 tpd of ore at the luxurious waste-to-ore ratio of 0.6 to 1. However, the complexity of the operation is enormous and the experience required to synchronize the various processes is masked by normal operations and only becomes apparent in times of emergency such as when the slide took place in the pit in February.

Jan 11, 1969

By E. J. Pasierb, H. W. Paxton

Mavkers ill a diffusion couple in the iron-chromium system move towards the high chromium side indicating Dcr > DFe at the marker composition. By a combituztion of measurements of D& and D a: a function of composition, this is also shown independently. DFe is calculated as a function of composition. and shown to be in reasonable agreement with measured values by other workers. MEASUREMENTS of marker movements in diffusion couples have been used from time to time to demonstrate that a vacancy or interstitial mechanism may be operative. Since there is a possibility that ring diffusion1 may be operative in chromium, the present experiments are of interest in showing some non-ring mechanism in iron-chromium alloys around the equiatomic composition. EXPERIMENTAL PROCEDURE The movement of markers originally at the interface between 1-in. sq sections of pure Cr (6 mm thick) and outer slabs of 30 Cr-70 Fe alloy was followed as a function of time at temperatures from 1150" to 1425"C, in a Kanthal-wound furnace. Temperature control was +5°C over extended periods. The analyses of these alloys are given in Table I. Selection of suitable markers presented a considerable experimental problem; the eventual solution was to draw quartz rod down to 0.01 cm and seat this in V-grooves 0.01 cm deep on each side of the chromium prior to welding. A preliminary experiment in which the groove was machined in the alloy gave identical results. Welding was accomplished by passing a heavy current through specimens under moderate pressure in a helium atmosphere. This method produced good welds with a planar interface as shown by subsequent metallo-graphic investigation. Any markers which did not adequately fill their groove and showed subsequent contamination from the atmosphere during heat treatment were not considered reliable. The composite sample was ground and metal-lographically polished on the four sides perpendicular to the interface. Fiducial marks (deep milled slots) were made outside the diffusion zone to check on total volume change. All necessary measurements were made on a metallograph reading to +0.0005 cm. The samples were wrapped in tantalum foil and given diffusion anneals for times to 200 hr in carefully purified dry hydrogen in a sealed McDanel porcelain tube. Chromium-zirconium chips were introduced near the specimen as an additional getter. The specimens were cooled relatively slowly after the diffusion anneal to preserve the McDanel tube but no significant error in effective time at temperature was thereby introduced. At least 1 mm was ground off the surface before measurements were taken. It was observed that the grain size following short diffusion anneals was several mm and was appreciably larger in the 30 Cr alloy than in the pure Cr. No significant grain boundary penetration was present as indicated by the etch limit. The results are presented in the next section. Measurements of D were made by standard sectioning techniques with chemical analysis. Machining difficulties limited the

Jan 1, 1961

By AIME AIME

0 N March 5, at Carnegie Hall, Cleveland, the Ohio Section held a joint meeting with the Cleveland Engineering Society, and the local sections of the American Chemical Society, American Society of Mechanical Engineers, and the American Society for Steel Treating. Prior to the meeting there was an informal dinner attended by 50 men. Then followed an address, "The Principles of Corrosion Protection," by Ulick R. Evans, the well-known British specialist in this problem. There were 266 present, presided over by Zay Jeffries, president of the American Society for Steel Treating and a member of the Cleveland Engineering Society. The address was well received and some discussion followed

Jan 1, 1929

By Henry W. Brandt

In a proposal submitted by Fenix & Scisson International, Inc., of Tulsa, Okla., conversion of an abandoned mine for underground storage of crude oil proved to be all effective storage technique. The conversion was done on an abandoned coal mine for S. F. F. Association, an agent of the South African Government, Johannesburg, South Africa. The mine was found to be structurally stable and appeared capable of retaining this stability over a long period. Surrounding formations were relatively free of fractures and were found to have low permeability. Slight problems appeared in the hydrostatic test, but were quickly stabilized. Additional information was positive, and conversion and filling were completed in 1969. Total puchasing, testing, and coverting cost was less than $0.20 per barrel of oil stored or 15% of conventional steel tank cost. Operating and maintenance costs are about 2% of those at two large tank farms owned and operated by the Association.

Jan 1, 1975

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thickners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter.

Jan 1, 1949

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of October, 1913: Members. BARNES, KENNETT F., Secty Granby Min. & Smelting Co., St. Louis, Mo. BILLINGSLEY, PAUL, Geol 526 Hennessy Bldg., Butte, Mont. BLANCHORD, RALPH C., Geol 3 Lombard St., London, England. BOYLE, ALBERT C., Jr., Prof. of Min. and Met., University of Wyoming, Laramie, Wyo. BRADFORD, JULIUS S., Min. Engr Chiksan Mining Co., Chiksan, Korea: CLEMES, ALFRED W., Min. Engr P. 0. Box 6,88, Moronic, Ariz. COPELAND, DURWARD, Met Cia. Estamifera de Llallagua, Bolivia, So. America. CRAWFORD, JOHN, JR., Mgr Noble Elec. Steel Co., Heroult, Shasta Co., Cal.

Jan 11, 1913

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-chairman. A. D. BEERS, Secretary. 55 Wall St. New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS. Chairman. R. L. AGASSIZ, Vice-chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston Mass ALBERT SAUVEUR, H. L. SMYTH Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON Chairman. FREDERIC KEFFER, Vice-chairman: LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane. Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 8, 1916

By B. E. Field

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The com¬mercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depending upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By R. L., Fullman

During the past year there have been a number of significant investigations that have furnished evidence on the driving forces governing grain growth and on the role played by boundary impurities. Thus Burke has shown that in high purity alpha brass the rate of grain growth in the earliest stages is approximately inversely proportional to the existing grain size. This relation agrees with one derived by Zener assuming that surface energy was the driving force in grain growth. Also in confirmation of the surface energy hypothesis, Burke found that growth virtually stopped when the grain boundaries or even only the grain corners were melted.

Jan 1, 1949