Search Documents

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:' I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By W. R. Crane

THE support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident then that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 9, 1924

ALABAMA Aldrich.-Lloyd, T W Anniston.-Carrington, F G Gerber, A B Heimrod, A A. White, H E Ashland.-Barton, J C Sturdevant, J C Bessemer.-Abbott, C E Ball, T L Hines, H K Hodgkin, W -0. Salmon, H S Thompson, N E Birmingham.-Adams, J H Adler, J. E Aldrich, T H Aldrich, T H, Jr. Ball, E M

Jan 1, 1923

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature microhardness of as-grown and annealed MoaC single crystals was measured on the (0001), {2110), and1012) planes using Knoop and Vickevs indenters at loads ranging front 25 to 1000 g. The orientatimz dependence of hardness with respect to crystal axes was also studied. The average random hardness of as-grown crystals was determined to be 1520 kg per sq nm. Annealing to 2000°C decreased. the average hardness by 150 units. An increase in hardness after annealing at 2200 ;C was noted. Optical and electron microscopy revealed slip and twin traces on all planes studied, as produced by mi-cvohavdness indentations. Basal (0001)(2i10) slip was determined to be the primary slip system and was substantiated by electron transmission microscopy. A secondary {1010)(2110) slip was produced by mi-crohardness indentations. The lattev also produced twinning- of the {10i2)[0001] type, as proven by electron diffraction. Electrical resistivity and elastic-modulus anisotropy were found and correlated with hardness anisotropy and Mo2C crystal structure. Elastic-modulus values were obtained by microhard-uess and ullrasonic methods. Bonding mechanism of Mo2C is discussed. ROOM-TEMPERATURE microhardness indentations are useful for studying hardness anisotropy, slip, and twinning in brittle materials. Slip has previously been produced in this manner in and WS~~.~ Recently, the authors5 reported slip of the {10i0)(11~0) type produced by high pressure and microhardness indentations on hexagonal TiBz (c/a = 1.066) single and polycrystals. This slip system was also reported by French and ~homas' and Taka-hashi and ~reise~ for hexagonal WC (c/a = 0.976) crystals. These results suggest that prismatic rather than basal slip is favored in hexagonal nonmetallic materials having a c/a ratio considerably less than the ideal (1.633). Buerger precession and cylindrical X-ray rotation patterns were previously' taken on cleaved sections of the Mo2C single crystals studied in this work. Th~y were found to be hexagonal MoaC with a. = 3.0233A, co = 4.7344A, and C/O = 1.5660. The latter ratio is close to that of the beryllium metal (c/a = 1.57), which slips primarily on the (0001) plane: but also slips on the (1010) planes.'0 ~irconium" (c/u = 1.59) and titanium12 (c/o = 1.59) deform mainly by slip on nonbasal planes which contain a close-packed direction. This is due to the fact that for these two metals the initial resolved shear stress for slip on the (10i0) prismatic planes is lower than that on the (0001) plane. The prominence of basal rather than prismatic slip in metals of high c/o ratios is shown by cadmium (c/a = 1.89), zinc (c/a = 1.86), and magnesium (c/a = 1.62) which deform mainly by basal slip. However, in case of the latter, by stressing magnesium crystals in tension or compression parallel to the basal plane, slip on (10i0) planes can also be produced.13 Several hardness values for polycrystalline Mo2C are reported in the literature: Biickle ' and Samsonov'~ give a value of 1800 and 1479 kg per sq mm, respectively, at a 100-g load; and Kieffer and Benesovsk~'~ report a value of 1950 kg per sq mm at a 50-g load. ~ott'~ reports a Vickers hardness value of 2000 kg per sq mm, with the load unspecified. A Rockwell A hardness value of RA = 88 has also been reported.'' In the present work, for comparison with single-crystal Mo2C hardness values, a Khnloo value of 1600 It 150 kg per sq mm was found on 99.6 pct pure and 99 pct dense hot-pressed Mo2C. This work was undertaken partly to explain the considerable differences in hardness values reported for polycrystalline Mo2C. EXPERIMENTAL The Mo2C single crystals investigated were prepared by a Verneuil-type process using an electric arc by the Linde Co. of the Union Carbide Corp.lg The largest specimens grown were boules 7 mm in diam by 40 mm in length. The crystals had an average density of 9.04 g per cu cm, with a Mo + C content of 99.8 wt pct. The major impurities were: 100 ppm each Na, Zr, and Ca; 85 ppm 0, 55 ppm Fe, and 10 ppm each Cr and Ta. The crystals were found to be carbon-poor, the average carbon content being 5.73 wt pct (stoichiometric value is 5.89 pct). The molybdenum content was found to be 94.08 pct, which is nearly stoichiometric. Electron-microprobe traverses of selected specimens were done with a Phillips-AMR microanalyzer. Thin-film and carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to optical and electron-optical studies, specimens were mounted in Lucite and polished on a vibratory polisher using diamond-paste grades ranging from 9-1 p and Linde A powder for up to 48 hr. Dilute nitric acid was used for thin-section polishing and chemical etching for 1-15 min. Electrical-resistivity measurements at room temperature were taken with a Rubicon bridge, using gold contacts. For hardness measurements, a Tukon Microhardness Tester Type FB with Knoop and Vickers indenters was used. Measurements were taken at loads ranging from 25 to 1000 g; however, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Indentations of cracking classes 1 and 2 only were considered for hardness determinations.20)21 (There are six cracking classes, ranging from "class 1" for a perfect inden-

Jan 1, 1967

By Luckie. Peter T., Deurbouck. A. W., Harold L. Lovell, E. R. Palowitch, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1974, 43.9% of the 603,406,000 tons (549,099,000 mt) of bituminous coal and lignite produced was cleaned mechanically, of which 82,280,000 tons (74,875,000 mt) was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 31 % between 1938 and 1974. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density inter- mediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes: 1) Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of 2 0.1 sp gr units. 2) Ability to maintain a separating gravity that can be controlled with ± 0.005 sp gr units.

Jan 1, 1979

By G. P. Conard, E. H. Rennhack

The generation of fibers composed of individual TiZn15 compound particles and their influence on crystallographic orientation in chill-cast, hot-rolled hypoentectic Zn-Ti alloys were explored. Metallo-graphic examination and X-ray diffraction data show that such fibers form a planar network after 50 pet reduction which eventually tends to suppress twinning at some critical reduction level (-90 pct) where the grain size approaches the interfiber, spacing. This leads to the development of a duplex-type projerred orientation through slip rotation consisting of an al-most ideal (0001)(2iiOj texture and a (0001) (1010) rotated component. Correlations between basal-plane rotation and secondary- creep rc11e sugg-est, however that prejerred orientation does not contribute in a major way to the creep resistance of these alloys. EFFORTS to improve the creep resistance of zinc through alloying without incurring a loss in fabricating properties have achieved only minor success with the exception of the very effective addition of titanium. Anderson, Boyle, and Ramsey,l for example, demonstrated that increasing the amount of thiselement from 0.05 to 0.23 wt pct produced a progressive, 45-fold increase in the inverse creep rate of hot-rolled

Jan 1, 1967

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler's saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By Norman C. Britz, Mortimer P. Buck

THIS PAPER DEALS WITH the practices used at the Huntington, Nest Virginia works of The International Nickel Company, Inc., in hot and cold rolling nickel and high-nickel alloys. The practical metallurgical aspects are discussed and a brief description of equipment given. The alloys covered may he divided into three main groups. based on their major constituents: 1. Nickel alloys, 2. Nickel-copper alloys. 3. Nickel-chromium alloys. The nominal compositions of the various alloys which are produced in most common mill forms are given in Table 1. Nickel, a commercially pure grade of nickel containing about 0.05 pct carbon as' the chief alloying element, is produced in all common Mill forms. "L" Nickel is commercially pure nickel in which the carbon content is held as low as possible, usually less than 0.01 pct. This grade of nickel is used chiefly for spinning and for special high temperature applications where its low carbon content enhances its corrosion resistance. "D" Nickel contains 4.5 pct manganese to provide improved resistance to sulphur embrittlement at elevated temperatures. "Z" Nickel is an age hardening grade of nickel containing carbon, aluminum, and silicon as the age hardening elements. This alloy combines the cor-

Jan 1, 1948

By L. M. Johnson, C. G. Janes

INTRODUCTION In May, 1966, the General Services Administration (GSA) announced a program to encourage additional domestic production of copper in the interest of national security. Upon learning of the copper production expansion program, Duval Corporation entered into negotiations with GSA for development of the Sierrita copper-molybdenum property under the program. Agreements between the GSA and Duval Sierrita Corporation, a wholly owned subsidiary of Duval Corporation, were concluded in 1967, with the Sierrita Concentrator beginning operation in 1970 at a designed capacity of 72,000 STPD. Subsequent additions and modifications have expanded capacity to 90,000 STPD. This property, located approximately 20 miles south of Tucson, Arizona, represents an investment including working capital of about $200 million. These funds were provided from an $83 million loan from GSA, repayable in copper valued at 38 cents per pound, $48.75 million of bank loans subject to U. S. Government V-loan guarantees, and Company capital contributions. Current general operating statistics for the concentrator are listed below: [Ore Grade 0.32% Cu., 0.030"/. Mo. Daily Tons Milled 90,000 STPD Annual Copper Product ion 94,600 Tons Annual Molybdenum Production 15,000,000 Lbs. Annual Silver Production 1,135,000 Ounces]

Jan 1, 1976

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By R. F. Campbell, R. F. Miller

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By J. J. Kramer, W. A. Tiller, G. F. Bolling

The temperatures of solid-liquid interfaces have been measured during the growth of Sn-Pb alloy crystals which exhibited a cellulur substructure. A simple descriptive theory was used in combination with this data and the other measurable growth variables to predict some features of the solute segregation such as the intercell excess concentration and the depth of cell grooves during freezing. The effective distribution coefficient at the tip of a cell, a, was predicted and experimentally found to vary in the range, 1 >a > k0. At the lower limit, the severe segregation that must arise between dendritic cells was substantiated by various observations such as the existence of a second Phase even for alloys of only 0.2 wt pct Pb. ThE cellular morphology of a solid-liquid interface is known to coincide with the formation of a zone of constitutional supercooling ahead of the interface during growth.' The occurrence of various cell structures, (two-dimensional cells, regular cells, dendritic cells), has been quantitatively investigated,'2,4 but the segregation of solute which arises as a consequence of this mode of growth has only been examined qualitatively. An indirect method of obtaining the solute concentration at the tip of a cell cap during solidification has been de-

Jan 1, 1963

Discussion of the paper of WALTER 0. SNELLING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. F. LUCAS, Washington, D. C.-Are the results of the experiments in practical operation? WALTER 0. SNELLING.-There have been no large-scale operations up to the present. The necessary conditions of temperature are easily arranged for, but the required condition of pressure, 800 lb., is not so simple a matter. The company has been working on this problem, and at the refinery in Oklahoma work of this kind is now being carried on. The way in which an ordinary still will leak at 50 lb., and more at 100 lb., leaves some doubt in the mind of many as to what can be clone at a continuous working pressure of 800 lb. On the other hand, the fact that they are making ammonia abroad by a method which employs higher pressures and temperatures than anything involved in this method, leads me to believe that the difficulties, which will undoubtedly arise when this is attempted on a commercial scale, can be overcome. WILLIAM N. BEST, New York, N. Y.-Is there any change in the calorific value of these oils?

Jan 5, 1915

By G. K. Burgess

§ 22. THe results published in Professor Howe's paper10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels " containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to 0.1 sec. for recording time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain's derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12 The observations were taken in vacuo on cylinders 5 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thermo-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 1, 1914

[Steel, iron which is malleable at least in some one range of temperature, and in addition is either (A) cast into an initially malleable mass ; or (B) is capable of hardening greatly by sudden cooling ; or (C) is both so cast and so capable of hardening. Variety A includes also molten iron which, if cast, would be malleable, as do its two sub-varieties, "ingot-iron" and "ingot-steel." (Tungsten-steel is malleable only when red-hot.)] does not seem to fit perfectly the requirement that it shall include all known varieties of steel and exclude everything else. The first requirement, that it shall be malleable at some temperature, is also possessed by some varieties of gun-iron—that is, mottled castriron, of which cannons have been made in the past by the South Boston Iron Co. and others. Gun-iron also meets the requirement (A) in being cast into an initially-malleable mass. The malleability was indeed not great, nor mas it made use of except to demonstrate the quality of the iron, but it approached in measurable degree that of some of the alloy-steels. As for requirement (B), some puddled-irons having from 0.2 to 0.3 per cent. of carbon may be hardened greatly, although this property is [lot utilized.

Jan 1, 1909

By John Chipman, Donald W. Murphy

RECENT developments in iron alloys containing nitrogen have indicated that this element may exert a considerable influence on the properties of the metal. This influence is not always in an undesirable direction and the indications are that nitrogen should be regarded as an alloying element, the amount of which should be subject to control, rather than as an inherently deleterious impurity. In controlling this element in liquid iron to the best advantage, it is necessary to have a reliable background of fundamental data pertaining to solubilities, rates of solution and chemical reactions of nitrogen in liquid iron. Obviously, the first step in such an investigation is the determination of the solubility of nitrogen in pure iron, and this has been the object of the experiments described in this paper. The solubility of nitrogen in solid iron has been measured by Zurich,1 Sieverts,2 Martin,3 and Iwasé4 and, the agreement among the first three inspires confidence in their results. No accurate determinations of its solubility in liquid iron have been recorded though several investigators have obtained approximate results. Strauss5 was able to introduce 0.03 to 0.04 per cent nitrogen into steel by the action of either ammonia or nitrogen on the liquid metal. This was accomplished by Eilender and

Jan 1, 1935

By Luther Wagoner

For a number of years I have, at odd times, tried to perfect a method of assay sufficiently delicate to find and estimate minute quantities of gold and silver. The object in view was to examine rocks remote from veins or mineral areas, in order to test the probability of the lateral-secretion theory. Having succeeded in measuring approximately the amount of gold and silver contained in one cubic centimeter of sea-water, I present a detailed account of the method employed, with some of the results obtained. General Method of Assay. The use of purified lead without other flux, blowpipe methods, extraction by cyanide, and measurement of the beads by the microscope. Purged Lead. The method of testing is by cupellation. On a properly prepared cupel, it is easy to cupel and find a bead of 0.002 mm. diameter. Such a bead of silver weighs about 1 part of a milligramme. A bead 0.02 mm. in diameter weighs about 1/24,000 mg., and a close approximation can be made to its weight. It is desirable that the lead used in the assay should be low in silver so as to avoid large correction, but as the parted

Jan 1, 1902

By H. H. Einstein

Swelling ground is one of the most feared problems in tunneling. Although usually not causing sudden failures during construction, the very large and longlasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners up to 1 m (3 ft) thickness that have been cracked or crushed, tunnel inverts that are heaving at 0.1 m (0.3 ft) per week during construction and continue to heave during decades. This paper summarizes essential components of design construction procedures where tunnels in swelling rock can be built to perform satisfactorily. It is important to point out that design and construction cannot and should not be separated. The way the tunnel will be built has to be an integral part of the design. Swelling can be defined as time dependent volume increase and is distinguished from squeezing, another time dependent phenomenon occurring in tunneling. Squeezing involves exceeding the shearing resistance while swelling usually does not. Swelling of rock masses can occur as swelling of the intact rock, swelling of wall rock, of gouge and of filler in the discontinuities of a rock mass, and as a combination of the above. Swelling mechanisms have been discussed elsewhere (ISRM 1983).

Jan 1, 1984