Search Documents

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

The Library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions are forced to spend a portion of their time in localities isolated from sources of information. To these the Library; through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention: The Library is prepared, to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general Information on the geology and mineral resources of-all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. HARRISON W. CRAVER, Director.

Jan 4, 1919

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that eventually the hydrometallurgist would have a wide selection of commercially available chemical reagents to make separations efficiently and economically of virtually all metals in solution under a wide range of conditions. Several years ago, General Mills began a research and development program to determine if it were possible to develop a reagent to extract a specific metallic ion from solution at a cost that would allow large scale commercial application. A giant step toward reaching this objective was announced in late 1963, when development quantities of LIX®-63 reagent, a highly selective reagent for the extraction of copper, were first offered to industry. The properties of this reagent were de- scribed in a previous paper.1

Jan 12, 1965

By Howard V. Sears

ArcHodrilling (Arcuate Hole Drilling) of short radius overhead curved holes from within the working level with a new, small-diameter in-the-hole drill produces tangible, assayable chip samples from the entire height of the projected mine level where the hole arcs down immediately in front of the working face. Drilling through the projected level with diamond coring tools produces samples showing the competence of roof and floor strata as well as the geological and economic characteristics of the ore. Hand-portable solid state electronic surveying instrument has been developed to survey the ArcHole and a convenient nomograph plotting record sheet converts survey digital readouts to hole inclination in degrees, to radius of curvature in feet, and to attitude of the plane of curvature from vertical in degrees, all without calculation. The ArcHodrilling system offers a tool with which the exploration geologist can more nearly assess the true potential of old mining properties being reexamined and to reduce the number of surface diamond drill holes needed to secure development data about new ore bodies. It gives the mine geologist an opportunity to secure those data at a fraction of the cost of drilling from the surface. The mining supervisor has a convenient, cheap tool to look ahead to know what he will be mining tomorrow. The mill supervisor has an opportunity to reduce his mineral loss in tailings by being able to anticipate the grade of his mill feed.

Jan 1, 1973

By C. S. Simons

Manufacturers of filtering, thickening or clarifying equipment, have been active in developing machines to meet increasingly rigid operator requirements, and the innovations resulting from this effort are moving into commercial applications. In general, the results of these applications are reported to be good. Little has been reported on progress in theory. The growing insistence on the part of pollution control agencies that waste water discharged into streams contain less and less suspended solids is being felt by a broad cross section of industry. A new clarifier, based on the often rediscovered fact that suspended solids settle more rapidly in inclined channels, is being marketed by Neptune MicroFLOC of Corvallis, Ore. This unit employs modules of inclined tubes, mounted in the upper zone of the clarifier, which carry the water flow. These were developed for light solids, such as those encountered in domestic water treatment and in paper mill waste water. In these applications, flow rates up to about three times those permissible in conventional clarifiers are reported to give comparable overflow turbidity. By combining these units with mixed media filters, high clarity may be obtained with minimum capital. Use of such units in the metallurgical industry, particularly where water reuse or effluent quality is important, should grow.

Jan 1, 1970

By Sidney Cornell

THE technical- advantages of adding oxygen to air and producer gas, or using it as a reactive agent, producing 400 B.t.u. gas instead of. the present 150 B.t.u., with higher flame temperatures and a reducing flame possible, with a smaller volume of gases passing through a furnace, will result in quicker melting, sharp working, and the production of a higher quality steel. Probably electric-furnace quality steel can be produced in an open-hearth furnace using oxygen. A modern, standard, 100-ton open-hearth furnace, with all equipment, costs from $350,000 to $500,000; there are about 1000 open-hearth furnaces in this country. When considering the use of oxygen in the open-hearth furnace, it is necessary to study: (1) The use of oxygen in the present furnaces, such that modification of existing furnaces and equipment cost the minimum, although the full advantages of oxygen are not thus obtainable. (2) The use of oxygen in a furnace designed for its use, producing quality and quantity steel at the lowest possible cost. This entails the junking of approximately one-half the value in existing equipment-writing off $250,000,000. The basis of such an estimate is the present cost of manufacturing open-hearth steel. Objection may be taken to some of the unit prices here given, but while some companies obtain their ores for much less, the prices quoted are -market price. They are used to show the maximum economy obtained by oxygen at that point.

Jan 11, 1924

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine milt",3 across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker&apos;s observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40&apos; to 45&apos; southeast

By Reno H. Sales

EVERY mine manager, mine geologist, and every prospector in the field who appraises the future of mining properties does so on the basis of a theory of ore deposition whether he recognizes this fact or not. Wherever the ultimate value of a mine or prospect is dependent upon undeveloped ore, any estimate by an engineer or geologist necessarily involves a theory of origin of the deposit. In view of these facts the importance of a thorough understanding of the genesis of ore deposits cannot be overestimated. It well may be that the greatness of our country will depend upon finding reserves of natural resources as yet undiscovered. The genesis of ore deposits offers a fascinating field for study and investigation. This is attested by the large number of geologists who have written at length on the subject. For progress made toward a better understanding of ore genesis we owe much to Kemp, Lindgren, Ransome, Vogt, Emmons, Spurr, Graton, and a host of others. Within my own experience, I have attempted to apply in practice the various concepts and theories that have been advanced by these men.

Jan 5, 1954

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passage- ways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground.

Jan 7, 1954

By Marcel Daly

THE writer has devoted a number of years to practical operations and to the study of geology in the oil fields. In consequence, he has been brought to investigate the theories advanced to account for the accumulation of oil and gas in commercial deposits. It is the result of these investigations and his personal conclusions that he wishes to sum up in this paper. The writer is an advocate of the organic origin of petroleum found in pools. He has been led to believe that the present theories of oil and gas accumulations are incomplete and, in certain respects, incorrect, although they may embody certain elements of truth; that the forces that are called upon to explain the movement are only secondary forces in the process, and insufficient, by themselves, to cause this movement; and that the phenomenon of accumulation is of much larger order than heretofore admitted and bears an intimate relation with the general as well as with the local deformations of the crust and is a direct consequence and a mechanical effect of these deformations to which the term "diastrophic" has been applied. As a complement to this theory, the writer offers a new interpretation of the "rock pressure" and of the mechanism of the "sealing up" of this pressure in oil and gas pools.

Jan 7, 1916

By B. Bernstrom

A 22-ft diam, 7-ft long, wet autogenous grinding mill was installed in the new Cretaceous plant of the Jones & Laughlin Steel Corp. to prepare crude iron ore for concentration in spirals and flotation cells. The paper describes the flowsheet and gives a description of the operating and metallurgical results that have been obtained. These results include capacity, horsepower, operating problems and a comparison of pilot plant results with those obtained in commercial operation. The Cretaceous plant at the Hill Annex mine of the Jones & Laughlin Steel Corp. was designed with a wet autogenous mill for grinding low grade iron ore so that it could be concentrated by spirals and flotation cells. The plant, on the west end of the Minnesota&apos;s Mesabi Range, went into operation in June 1961, and preliminary operating and metallurgical information describing the performance of this mill can now be given. The crude is lean ore from the Cretaceous iron foundation. This formation is a beach deposit of Cretaceous age that overlies the Precambrian direct shipping and concentrating ores. This rock in nature is not extremely hard but is quite resilient, resisting blasting in mining and size reduction in milling. It contains hematite as water-rounded particles and other fragments of the underlying iron formation and adjacent rocks cemented together by a high alumina-silica ferruginous matrix. It is interspersed with hard dense hematite agglomerates and also contains granite pebbles and boulders that were not cleaned off during removal of the surface. It has a 3.48 sp gr and in the stockpile the material consists of frag-

Jan 1, 1962

Lester Guttman (General Electric Research Lab-boratory)—Seybolt has measured the thermodynamic activity of silicon in dilute solution in a iron. The anomaly which appears at 800 °C in the approximate range 1 to 6 wt pct Si is most naturally attributed, as Seybolt has done, to the existence of a region of

Jan 1, 1960

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By E. Werchowsky

FOR over four years, since the revolution of 1917, Russia has been cut off from the Western world. Political and general economical reforms have attracted the attention of the public and business world, but mining men have had no information as to the situation in their branch of industry, as various articles which have appeared in the European and American press gave little information as to actual conditions in our country. When the Soviet system of government was estab-lished and private ownership abolished, it affected the FIG. 1.-ORGANIZATION OF THE COUNCIL OF MINES. mining industry very little at first. The power of the Soviets did not affect the Ural provinces nor Ukraine or Asiatic Russia (Siberia, Turkestan, etc.) during 1918 and 1919, and, as is well known, the mineral wealth of the republic lies within those boundaries. In the Ural Mountains are copper, gold, and platinum; in Siberia, silver, lead, zinc, and gold, and the coal deposits in Koushetz district; in Ukraine, there are the coal fields of Donetz and the iron mines of Krivvy Rog, and silver, lead, zinc, copper, oil, etc. in the Cauca-sus. The mineral resources of Central Russia are the coal fields of Moscow (low-grade and brown coal), turf deposits, iron mines in Tula and Kalonga provinces, and quarries of granite and other building materials.

Jan 8, 1922

1938 ABERNATHY, G E Feb 6, 1948 Min & Met Apr 1948 1937 ADAMS, ARMY Aug 20, 1949 Min Eng Dec 1949 1946 ADDY, GEORGE E Sept 24, 1950 Min Eng July 1951 1920 ALDERSON, WILTON P Feb 1951 Min Eng Sept 1952 1896 ALDRICH, T H , JR May 24, 1950 Min Eng Aug 1950 1942 ALDRIDGE, LEONARD June 8, 1952Jrn Met Sept 1952 1919 ALLEN, ROLLAND C July 18, 1948 Min &Met Sept 1948 1950 ANDERSON, C P Unknown Min Eng Feb 1951 1937 ANDERSON, JOHN H May 10, 1950 Min Eng Aug 1950 1914 ANDERSON, L DOUGLASS Unknown Min Eng Nov 1951 1948 ANDRAU, E W K Oct 20, 1951 1936 ANDREWS, CHARLES B Apr 19, 1950 Min Eng June 1950 1918 ARMITAGE, PAUL June 28, 1949 Min Eng Oct 1949 1924 ARMSTRONG, PERCY A E Jan 23, 1949 Min Eng May 1949 1906 ARNOLD, CHARLES LE NEVE Aug 7, 1949 Min Eng Oct 1949 1945 ARNOLD, HAROLD S Aug 7, 1950 Min Eng Oct 1950 1936 ASH, JAMES E Dec 17. 1949 Min Eng Apr 1950

Jan 1, 1952

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,&apos; and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0&apos;65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc&apos; The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,&apos; and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0&apos;65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc&apos; The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948