Search Documents

By M. R. Pickus, C. H. Mathewson

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centcred cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers," were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938

By Ronald W. Utley

INTRODUCTION The ''Do's and Don'ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO'S and Don'ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer's local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer's shop order number (after order placement) •Serial number (after manufacture) DO'S 8 DON'TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer's recommended typical foundation drawings. If substantial alteration to manufacturer's drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By M. J. Kirwan, K. A. Covell

This paper covers a brief discussion of pumping 38° to 41° gravity oil from Wilcox sand wells ranging in depths from 4000 to 4900 ft. in the Seminole field, Oklahoma. As recently as a year ago it was the general belief among Seminole operators that most wells in that district could not be successfully or economically pumped. Also the idea was prevalent at that time that the crookedness of the rotary holes would cause a large amount of mechanical trouble and the use of the air-gas lift would leave the wells depleted with sand conditions and fluid levels unfavorable for pumping. At that time it was predicted that wells would be abandoned when the economic flowing and swabbing period was reached. Contrary to these beliefs it has been demonstrated that wells can be profitably pumped to limits as low as 10 bbl. of oil per day where conditions are favorable. The Serllinole field, unusual in its rapid development, has served as an experimental laboratory for many oil field pumping devices with which this paper will not concern itself. Discussion will be confined to equipment and methods in general use throughout the field. The outstanding features of equipment and pumping operations covered in this paper may be summarized as follows: 1. Pumping equipment from the standpoint of prime movers, energy cost, power transmission equipment, derricks, counterbalances, beam hangers, tubing, sucker rods, pumps, etc. 2. Pumping problems peculiar to the Seminole field, including the proper time at which to change from air-gas lift flowing to pumping. Pumping Equipment There have been no basic changes in pumping equipment in the past 20 years with the exception of some refinements in design brought about by the demand for equipment suitable for pumping deep wells. Results of research in the heat treatment of metals and progress made by the American Petroleum Institute in standardization of equipment, together with the cooperation of oil field equipment manufacturers, have

Jan 1, 1929

By H. M. O?Harra

Experiments have shown that the use of enriched air would be of particular benefit in the roasting of zinc ores for the manufacture of sulfuric acid. Enriched air increases capacity of furnace, decreases fuel consumption, and increases SO2 content of roaster gas. THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper distribution of heat in the furnace;1 the volume of enriched air,

Jan 3, 1924

By Emile Rector Abadie

The picturesque little mining town of Grass Valley, nestled in the foothills of the Sierra Nevada mountains, at an altitude of 2500 feet, has been for 43 years the scene of uninterrupted activity and prosperity, as the center of a mining district which was intimately associated with the pioneer days of California, and the discovery of gold by James W. Marshall, in El Dorado county, in January, 1848. Although placer-mining was inaugurated in Nevada county as early as 1848, the first quartz ledge was not located until the summer of 1850. Discoveries made on Gold Hill and Massachusetts Hill increased the excitement in quartz-mining, and hastened the erection (during the same year) of the first mill operated in the State. At the close of 1864, the district had produced $23,000,000 in gold, and all the well-known properties of to-day had been discovered and worked. The Eureka-Idaho, the North Star, and the Empire mines were in active operation ; and to-day we still find them equipped with large crushing-plants, operating 80 per cent. of all the stamps in the immediate Grass Valley district. Of the mines just named, the North Star possesses the most recently constructed mill, a description of which, the writer believes, may prove of interest to members of the Institute engaged in the milling of goldores. During the year 1386, operations at the North Star mine (the property of the North Star Mining Company) had reached such a stage of development that the necessity of a crushing-plant at the mine became imperative, and early in October the erection of a 30stamp mill was in progress. The building designed to contain 40 stamps was speedily erected ; and within sixty days the large structure was under cover. Plate A represents the appearance of the mill 40 days after work was commenced. Late in February, 1887, the mill was in readiness, and, upon the

Jan 1, 1895

By J. L. Jernegan

IN this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié, process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two wind-furnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

Jan 1, 1874

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By F. H. Willcox

In Bessemer-steel practice, air is blown through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and cafbon. Toward the end of the blow, when the iron is not protected from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Besserner and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast iron. is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blow holes lies in part in the presence of dissolved oxide of iron in the molten steel and its consequent reaction with the carbon of recarburizers, when these are added, to form gases. (Another factor in the origin of blow holes is, of course, the solubility of gases themselves in the steel and

Jan 1, 1917

By P. W. Bridgman

It is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand. It appears that one's interest in, and satisfaction with, the discovery of an array of new experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner. Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows. Of course, there have been long arid stretches in the history of physics in which new data of unquestioned ultimate importance have piled up, without much inspiration or illumination in the way of understanding. For 50 years spectroscopy had such an arid history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered. The investigations in the field of high pressure, which have occupied me for a long time,' until the last few years have been in very much the same sort of situation as spectroscopy before the advent of Bohr. A great many kinds of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected. But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going. However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By J. H. Hensley

The mine of the Miami Copper Co. is in the Miami district, Gila County, Ariz., approximately 7 miles west of Globe. In 1906, the General Development Co. secured the ground now owned by the Miami Copper Co., and about a year later discovered ore in a prospect shaft at a depth of 220 ft. The Miami Copper Co. was organized in 1907, the claims held by the General Development Co. were transferred to it, and an active development campaign was inaugurated. The railroad was extended from Globe to Miami in 1909, a concentrating plant was constructed, and the company began producing early in 1911. The unit size of mineral tract in the district is the standard lode claim 600 ft. in width by 1500 ft. in length. Ownerships of land are held in fee. The geology of the district has been described by F. L. Ransome.' The formations of local importance are: The pre-Cambrian Pinal schist, which consists mainly of metamorphosed sedimentary rocks and is commonly of a thinly laminated sericitic variety; the diabase, which is thought to have been intruded in late Paleozoic or early Mesozoic times; the Schultze granite and granite porphyry, considered early Tertiary; the dacite of late Tertiary time; and the Gila conglomerate of early Quaternary. General Items Influencing Mining Methods The bodies of disseminated ore in the district are flat lying masses of irregular outline and variable thickness. As a rule, these masses lack definite boundaries; the orebody follows a curve along one of the main ridges, approximately 5500 ft. in length with a maximum width of 1600 ft. The minerals occur as finely divided and uniformly disseminated chal-cocite in the Pinal schist and Schultze granite. The typical overburden or capping is a barren rusty brown, very friable, highly siliceous, leached schist, or granite-porphyry. The topography of the district is fairly rugged and irregular; the altitude ranges from 3400 ft. above sea level, at the town of Miami, to 3900 ft. on the hills above the Miami orebody. The climate is mild; the mean annual temperature is 63.°F.

Jan 1, 1925

By Waldemar Lindgren

I. INTRODUCTION AT the time of the discovery of America the old world had a scant supply-of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the nines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia and some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon wade the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 4, 1916

By R. S. Cartwright

TWO types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent on the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination—the combination which when engaged will suspend the least amount of weight—has a value of 1.00. According to the table there are "blind spots" in the series. This is true particularly among the lowest ratios, which are most used to suspend the major part of the weight when great depths are reached. It will be noted that there is a difference of nearly three units in the value of the

Jan 1, 1929

By William P. Blake

It is scarcely necessary to point out the important functions of water in the mining operations of man, especially in the State of California, where sluicing and hydraulic mining have been practiced on such a grand scale as to arouse the opposition of the agricultural interests. But the role which water and ice have played in mining or excavating on their own account is not so apparent. The alluvions of existing rivers, and the higher gravel-beds left by ancient streams, are doubtless the result of running water; but how far these gravelly materials owe their origin primarily as rocky debris and fragments of veins to glacial erosion, it is difficult .to determine. Yet we see on every side in our higher mountains unmistakable evidences of the cutting, crushing and eroding effects of glacial ice. We note that mountain-summits have been reduced in height and shaped into rounded and dome-like summits. We know that the general contour of the hills of New England, of the Highlands of the Hudson, and of the mountains of northern New Jersey, is due to glacial carving. The same is true of the Laurentian hills of Canada and of the mountains of all northern regions. And we recognize in the vast deposits of so-called " drift," which are spread out over the surface of the northern States, the chips and debris from the glacial workshops. Thus we cannot avoid the conclusion that there was an enormous amount of cutting and excavating in glacial times, and that vast quantities of veinmaterial and of ores and metals must have been liberated by ice-action.

Jan 1, 1900

In introducing last year's Industrial Minerals Review, Stan Lefond accurately predicted that the 1974- 75 period would be quite difficult and frustrating. Although 1974 demand and prices for most industrial minerals were exceptionally strong, operating costs also rose rapidly-while shortages of supplies and equipment, symptomatic of an overheated economy, occurred from coast to coast. Thus, at the end of 1974 recessionary forces were accelerating-and the minerals industry will soon be facing falling demand as a consequence of sharp declines in auto production, housing, appliances, and other consumer goods. Moreover, when sales weaken, the high-volume, low-prices industrial minerals will incur sharply increased unit costs. To maintain adequate profit margins under these conditions will require cautious and perceptive management.

Jan 2, 1975

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By J. O. Lewis, H. R. Pierce

Since the sudden revival of the air or gas-lift and its extensive use in the oil fields, many questions have arisen as to principles and as to their application under the conditions actually encountered in the field. Much has been written regarding both theory and practice, especially on the air-lift as applied to lifting water. Many statements have been made as to the use and benefits of the gas-lift, some of which are reasonable but many of which are unreasonable, many specialty makers claiming to have devices which operate in almost miraculous ways and even to generate energy nature never possessed. These claims are often based upon incomplete or inaccurate data. A review of the literature discloses many valuable articles, but it also discloses the need for setting out more clearly the different practical ends sought, and for working out specific engineering principles upon which to formulate the design and operation of gas-lifts to meet the desired ends within the limitations of field conditions. A check on some of the published information has revealed basic errors in the sources of data upon which conclusions have been predicated and has led the writers to doubt the value of a large part of the compiled data. The writers have concluded, therefore, that it will be opportune to direct discussion to the sources of error in the data now being collected, to recommend for consideration by the engineers some methods of collecting and correlating data, and to point out some of the factors relating to the application of the air-lift principle to oil production as dictated by the different economic ends sought, and the limitations of working conditions that may be met. Until these several considerations are clearly understood by the engineers, and the unreliable data have been sifted out and dependable data substituted, there seems little chance of evolving satisfactory engineering control for the air-lift. In the following pages no distinction will be made between gas-lift and air-lift, as they are generically the same.

Jan 1, 1928

By Oswald J. Heinrich

The deposit of rock salt along the shores of Lake Huron, in Canada, has been brought before the public during the last six months, in consequence of the developments made by the diamond drill at Goderich. It is likely to be of more than common interest in the future, since now actual operations have been commenced to exploit the deposit and work it by regular mining. The methods of mining rock salt being but little known in this country, it may be of interest to make a few general remarks in regard to them before entering, upon the description of this new mining enterprise. According to the conditions under which salt is .found in nature, various methods have been resorted to, in course of time, to make it available for the human race. They consist in: A. Natural or solar evaporation. B. Artificial evaporation, either exclusively or in connection with the former. C. Mining the rock salt in its natural state, and converting it to a marketable product, if need be, by simply pulverizing it. Without going into the details of the various methods of making salt available in an economical point of view, dependent on its degree of pority, or on various local influences, we cannot refrain from alluding to the general principles which influence the mining and manufacturing of salt in countries where they have been carried on for hundreds of years. ECONOMICAL CONDITIONS FOR SUCCESS. Salt being one of the articles of prime necessity, and one universally distributed throughout nature, it must always be sold at a comparatively low price. It would even be quoted in the market at prices far below those now ruling, if it were not for the high duties generally imposed upon it, for purposes of state revenues. But looking closer into the subject, it will be found that this duty is probably one of the least oppressive, although in some countries it exceeds sixfold the cost of profitable production. To produce the article at the lowest possible cost requires, therefore, a

Jan 1, 1879

W. P. Blake, Shullsburg, Wis.: I desire to express my admiration of Prof. Posepny's memoir, and particularly of the charming manner and spirit of the introduction. With respect to his mention of the ore-deposits of Missouri and Wisconsin, reference may be made to my paper presented at this meeting (Trans., xxii., 621)) showing the existence of dislocations and breaks in the bedding, and their apparent close relation with the localization of the ore-deposits as claimed by Dr. James G. Percival, and also so claimed by Dr. Jenney in his paper before us (Trans., xxii., 171). I have in my paper given reasons for believing that the zinc- and lead-ores in the strata above the compact Trenton limestones were formed by lateral secretion and concentration from above downwards, substantially as shown by Prof. J. D. Whitney, and not by the ascent of solutions through the fissures, as Prof. Posepny (p. 304) seems inclined to believe. In regard to the contemporaneity of the ore and the rocks, and in favor of a later introduction of ore through fault-fissures, Prof. Posepny (p. 310) cites the influence of these fissures. In my paper, already referred to, I have endeavored to show how faults may have influenced the deposition of ore without being themselves channels for the flow of mineral solutions, and how they may have caused the contemporaneous formation of metallic sulphides from sea-water in the body of a forming rock; the faulting fissure being formed at an early period in the foundation rocks, and probably continuing to be a plane of break and movement in the deposits of later formation.

Jan 1, 1894

By Bartlett W. Paulding

Since its introduction to the petroleum industry in 1949 by Clark,1 hydraulic fracturing or "hydrafracing" has developed into a widely respected and useful technique for increasing production from petroleum reservoirs. Even then, Clark described production increases of from 6 to 100 barrels of oil per day (bopd). Since that time, others have described treatments in which production increased from 12 to 456 bopd, from only a show to 40 bopd;2 from 48 to 219 bopd; 3 from 500 to 1400 bopd and from a show to 192 bopd.4 Although representative of only a few of many successful hydraulic fracturing operational6 these increases in production attest to the past and potential value of the hydrafracing technique to the petroleum industry. The technique has received a considerable amount of theoretical and experimental attention.1, 5-20 Unfortunately, however, the degree of general understanding of the mechanics of hydraulic fracturing is still inadequate to solve many recurring problems. The practicing engineer is plagued with difficulties in predicting such factors as: (1) the required pressure and viscosity of the fracturing fluid to not only induce the fracture but to control the extent of its growth, (2) the strength characteristics and amount of proppant to include in the fluid so that the fracture is held open once the fluid pressure is decreased, and (3) the volume of the reservoir influenced by the induced fractures and the resulting increase in production. A major cause of these difficulties is the uncertainty associated with determining the orientation of the hydraulically induced fractures. One's natural conclusion in considering the problem is that the orientation of the fracture would depend on several variables, as, for example, the relationship between the viscosity and injection rate of the fluid and the

Jan 1, 1968

By Henry T. Mudd

FLUORSPAR is a nonmetallic mineral aggregate or mass containing a sufficient quantity of fluorite (CaF2) to be of commercial interest. It has only moderate value per unit of weight and its cost as a percentage of the cost of finished consumer products is nearly negligible. Nevertheless, it has wide and great industrial importance. In periods of national emergency it is a mineral without which many very necessary manufacturing processes would be greatly handicapped; a few could not exist. Fluorite contains 51.1 pct calcium and 48.9 pct fluorine. Industrial grades of fluorspar prepared for the consumer normally contain from 85 to 98 pct fluorite, depending on the use. The ores may contain as little as 30 pct fluorite, depending on many factors such as accessibility to transportation and markets, character of ore, and prices. Fluorite is a lustrous, glasslike mineral, generally translucent to transparent; it may be clear and colorless or range in color from slightly bluish through various shades of violet, amethyst, purple, green, and yellow. It crystallizes in the isometric system and possesses perfect octahedral cleavage. Commonly it occurs in masses of very pure crystal- line material with aggregates of cubical crystals in open spaces, but - it is also found in fine to coarse granular form. Banded veins and masses with fibrous, radiating structure occur locally. It is usually found associated more or less intimately with other minerals and rocks, from which it must be separated for commercial use. The specific gravity of fluorite is 3.18 and the hardness is 4 in the Mohs scale, compared with 7 for quartz and 3 for calcite. It is distinguished from calcite by its failure to effervesce with dilute hydrochloric acid. Heated with sulphuric acid, it gives off fumes of hydro- fluoric acid, which etch glass.22,25,33.34,35.41

Jan 1, 1949