Search Documents

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By André R. Laplante

"This presentation reviews three continuous centrifuge separators, the Falcon-C, Kelsey Jig and Multi-Gravity Separator, two units with possible synergies with centrifuges, the In-Line Pressure Jig and InLine Leach Reactor, and two centrifuge prototypes, the continuous Knelson and the Altair Jig. Typical applications, potential problems, promising synergies and general concentration mechanisms are discussed. A general discussion on the sources of information, the nature of the fluidization water flow, test work for potential centrifuge separations and the early life cycle of new technology, using centrifuge separators as an example, follows. ResumeCette présentation fait le point sur trois appareils de séparation centrifuge, le Falcon-C, bac oscillant Kelsey et Multi-Gravity Separator; deux appareils qui présentent des synergies possibles avec les centrifuges, le bac oscillant In-Line Pressure Jig et le système InLine Leach Reactor; et deux prototypes centrifuges, le Knelson continu et le bac oscillant Altair. On y présente des applications typiques, les problèmes d’opération les plus usuels, les synergies les plus intéressantes. On discute également des sources d’information disponibles pour le minérallurgiste, de l’impact du mode d’ addition de l’eau de fluidisation, de la démarche expérimentale a faire avant d’installer un centrifuge, et du cycle de développement de nouveaux équipements, en utilisant les centrifuges comme exemple.IntroductionGravity separation has undergone a renewal in the past 20 years, much of it attributed to centrifuge units. The semi-batch Knelson Concentrator has probably received the most exposure, but it is rather because of the shear number of units sold than the width and breath of its applicability. It excels at recovery very dense minerals in very small concentrations, and has become a workhorse of the gold industry. Falcon’s Super-Bowl comes a distant second, with very similar applications. A number of copycats are available, and are generically identified as “Knelsons.” This presentation will not address these units explicitly, but as possible synergies."

Jan 1, 2000

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By Wilton Johnson

Native asphalt was produced in 1982 by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries, Inc., Uvalde County, Tex. Historically, gilsonite, a solidified hydrocarbon found only in Utah and Colorado, had been mined by American Gilsonite Co. and by Ziegler Chemical and Mineral Corp. from properties near Bonanza, Uintah County, Utah. During 1982, Hydrocarbon Mining Co., a subsidiary of the Oberon Oil Co., entered into a joint venture with Miocene Resources Inc. of Novato, Calif, to form Hydrocarbon Resources Co. for the purpose of mining gilsonite about 50 miles south of Vernal, Uintah County, Utah. Under the agreement, Hydrocarbon Mining contributed gilsonite-bearing properties held by lease or sublease as well as mining equipment to the venture. The property contained leases totaling 760 acres with probable reserves of 268,000 tons of gilsonite. Miocene Resources provided the partnership with a minimum of $200,000 to develop two of the leases and were to be responsible for management of the mining operations.2

Jan 1, 1983

By M. Abdellatif

The Mintek Thermal Magnesium Process (MTMP) process is based on DC open arc metallothermic smelting of calcined dolomite at normal pressure and temperatures of 1650?1750°C. The process was demonstrated at the pilot scale in the period 2000?2004. Major changes to the MTMP pilot plant were made throughout the development period, which lasted for about five years. The changes included design and installation of new equipment, modification of existing equipment, changes in the metallurgical approach in terms of feed rates, feed recipes, furnace operating temperatures, cold and hot dolime feeding, and steady and systematic changes in the operating procedures and maintenance of the plant. As a result, the performance of the pilot plant gradually improved from one campaign to the next, in terms of availability and in particular the condensation efficiency. In Run 10, the process was successfully demonstrated over an 8-day campaign. Keywords Magnesium, condensation efficiency, DC arc furnace, silicothermic reduction.

Jan 1, 2011

By H. Lyn Bourne

This marks the 15th consecutive year for this column. During 1995, readers were asked to supply royalty data for construction raw materials especially for states where none is available. The response was discouraging and royalty data are still missing for several states for either sand and gravel or crushed stone. Several readers have said that this article has merit but more new information is needed to justify its continuation. Several articles and pieces of news relative to mineral royalties appeared in the trade journals. R. Lee Aston (E&MJ, November, 1995, p. 16N) described South Australian royalties as amended by the government in1994. The royalty rate (a percentage) was lowered but the assessed value for minerals was raised and the current rate amounts to 20 cents//t (18 cents/st).

Jan 1, 1996

By M. Lahtinen, P. Latostenmaa, I. Kojo, E. Peuraniemi, M. Lindgren, S. Jyrkönen, M. Jåfs

The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. Since then Flash Smelting technology, now owned and developed by Outotec Oyj and the first plant, now owned by Boliden Harjavalta Oy, have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a popular theme during the first days of Flash Smelting, it has still been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. This paper describes the history and improvements of the Outotec® Flash Smelting process by looking into the early days of operation and how the development of the process and equipment has taken place over time as a joint effort between the technology provider and the users of the technology. INTRODUCTION In the 1940s, Outokumpu Oy refined the concentrate produced in the Outokumpu mine into metallic copper initially in Imatra, and later from 1945 to 1949 in Harjavalta, based on the most modern electrical melting process of the world at that time. After the war, Finland lost a significant part of its hydropower production, and due to the increasing use of electricity, the availability of electricity weakened, and the price rose. To maintain Outokumpu's profitability, it was forced to look for a melting solution that was not based on electricity.

Jan 1, 2019

By A Golsby

Although much talked about, social licence to operate (SLTO) is a relatively new concept that has been deemed as one of the four biggest business risks to a mining project over the life-of-mine. There is no accepted single definition of SLTO and this author understands SLTO to be stakeholder perception of the legitimacy of a project, a company or an industry. At a specific site, and across different sites within the same organisation, SLTO ranges through different levels according to stakeholders’ degrees of acceptance in time and space. Management of SLTO is vital for the mining sector but is difficult as it is informal and intangible. Although there are no key performance indicators, there are certain indicators that enable relative measurement of the ‘level’ of the SLTO. Because of the importance of the SLTO, information management during the entire life-of-mine, from exploration to rehabilitation, becomes crucial for the continued operation of a project. This paper identifies ten basic principles for the management of information to support the SLTO.CITATION:Golsby, A, 2014. Managing information to support a social licence to operate, in Proceedings Life-of-Mine 2014 , pp 389–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The Hill 50 Gold Mine is situated at Boogardie, 3 miles on a bearing of 295 degrees from; Mount Magnet township. Mount Magnet lies 300 miles north-north-east of Perth, Western Australia (Fig. 1).The older workings of the mine may be identified with those of Sirdar, Gold Mining Lease 696M The Sirdar had been worked before 1902 though no records remain, and irom 1903 to 1912 about a thousana tons at a grade of 6' 2 dwt. was extracted annually; by the end of 1918 6,225 oz. of gold had been obtained from the milling of 17,852 tons of ore. In view of these yields, and the length and width of the lode, this mine was early recognized as one of the most promising in the district. From 1919 to 1924 the ground,including G.M.L. 1282M, was held as Mt. Zion G.M.L. 1183M.The Hill 50 Gold Mine N.L. company took up the workings as Hill 50 G.M.L. 1282M in 1934 and have continued operations to the date of writing. To the end of 1956 the Hill 50 Gold Mine had yielded 982,106 tons of ore for a return of 448,'602 fine oz. of gold.The mine has been described by: J utson (1915), Feldtmann (1920), Johnson (1949), and Finucane (1953). Finucane (1953) details the mine structure to a depth of 414 ft. The author was able to examine the mine to a depth of 1305 ft. Detailed main level mapping to the 1060 level and a detailed surface examination have revealed aspects of the structure which were previously obscure.

Jan 1, 1960

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By Patricio Santis, Jacopo Seccatore

Artisanal and Small-scale Mining (ASM) is a prominent activity in the extractive industry: considering only gold, it produces about 20% of world market supply. Despite this fact, ASM is generally associated with negative aspects of its environmental impact, and operational research is generally neglected. This paper emphasizes the peculiarity of the drilling and blasting systems of small underground mines in selected South American Countries. Such Countries, while having large mineral deposits and well recognized large-scale mining activities, at the same time still present on their territory ASM activities that are archaic, highly inefficient and dangerous for the safety of its operators. This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained. One case shows how blast pull efficiency can be increased of from 82% to 98% by changing non-rational applications of explosive products. Another case shows how, by rationalizing blast designs, drilling and blasting costs can be reduced by 9% per month, the advance by blasting increased by 29% and the blasting efficiency increased from 70% to 90%. Finally, it is concluded that examples of application show how operational improvements are easily applicable on the field, relying only on tools and resources of artisanal mining, but combining solid engineering bases with confidence-gain and respect for the experience of the miners.

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

The Pike River Coal Company is set to develop the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. As such, the major restriction to planned extraction is protection of:   +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2005

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001