Search Documents

By David Newman

In Eastern Kentucky, the Darby seam has had an extensive history of coal bumps and pillar bursts. The combination of high overburden, strong rock and coal, subjacent and superjacent mines, and retreat mining has produced incidences of violent pillar failure. The influence of these factors on pillar stability and the potential to bump is illustrated in two case histories. In the first case history, a bump occurred unexpectedly during the retreat mining of a five heading continuous haulage panel. Alternative cut sequences and pillar dimensions were analyzed to identify a geometry that would reduce the potential for future coal bumps or bounces during retreat mining. The viability of the alternatives was constrained by the reach of the continuous haulage system, the overburden depth, and the presence of thick sandstones in the main roof. Each alternative was numerically modeled cut-by-cut to examine the mechanism of stress transfer, as a pillar row is retreat mined. This approach highlighted which cuts were being made in highly stressed portions of a pillar and therefore more prone to coal outbursts. Validation of the numerical modeling was accomplished by comparing the cuts where bumps and outbursts had occurred underground to the highly stressed cuts shown within the models. Recommendations of the barrier pillar width between adjacent panels, pillar dimensions, and changes in the retreat mining sequence were proposed based upon the overburden thickness, geology, and the result of the numerical modeling. The second case history documents a nine-entry panel 3,600-feet long that was retreat mined a distance of 2,064-feet without a significant roof fall or roof-floor convergence. Mine management became concerned about the potential for a coal bump or a large roof collapse within the gob and the resulting air blast. The stress on the pillar line and within the remnant pillars in the gob was quantified through numerical modeling. Changes in mining practices on the current panel were implemented to avoid a bump in the active panel. A barrier was established between the current and the future panels to protect the future panel against abutment pressures from the void area. A change in pillar centers was proposed in the adjacent panel to absorb the side abutment pressure from the gob of the active panel.

Jan 1, 2008

By Steve Custer, Tim Kahl, Sue Parker

"The primary objective of the Barrick Goldstrike expert system is to achieve the desired liberation size for the autoclave circuit while maximizing throughput. In addition, when downstream limitations (autoclave circuit or others) restrict the milling circuit tonnage the expert system further improves grinding product size. Since its implementation, the expert system has provided expected throughput improvements while improving or maintaining circuit performance.Barrick Goldstrike and MinnovEX Technologies Inc. teamed up to install an expert system to control Line I and I1 of the autoclave grinding circuits. The dissimilar equipments of the two grinding circuits coupled to different production objectives, skepticism among operators, and the variability of the ore types processed in each line challenged the implementation.To ensure implementation success, Barrick Goldstrike dedicated four administrators full time to the project. The system administrators included two metallurgists, a process control engineer and a mill trainer. As usual, the control room operators were the experts who provided the operational logic for the foundation of the control system. The administrators and all eleven of the control room operators signed off on acceptance of the system. Current online utilization is 95%.INTRODUCTIONThe grinding circuit for Barrick Goldstrike’s autoclave process consists of two SAG Mill Ball Mill lines. Line 1 grinding circuit is comprised of a 22 by 8 foot, 2500 horsepower Allis Chalmers (AC) variable speed SAG mill, followed by a 12.5 by 14 foot, 1250 horsepower AC ball mill, and a 13.5 by 18 foot, 1800 horsepower Dominion ball mill in parallel. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1352 Nordberg Omnicone crusher (4.5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The ball mill circuit is closed with 6 Krebs super D20 cyclones. Line 2 grinding circuit is comprised of a 24 by 12 foot 4000 horsepower Fuller variable speed SAG mill followed by a 16.5 by 30.5 foot 5000 horsepower Fuller ball mill. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1560 Nordberg Omnicone crusher (5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The line 2 ball mill circuit is closed with 12 Krebs super D20 cyclones. The underground Meikle ore is typically fed through Line 1. Achieving the desired product size is critical for successful processing of Meikle ore. Open pit Betze ore is fed to Line 1 when Meikle ore is unavailable. Line 2 processes Betze ore exclusively. Throughput is maximized when processing Betze ore as the product size is less critical. The products of these two circuits are combined as feed to the autoclave circuit. The ore types and the autoclave circuit demands determine the required grinding circuit product size and maximum combined mill feed tonnage."

Jan 1, 2001

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By Magued G. Iskander

The deterioration of concrete, steel, and timber is a serious hindrance to construction in marine and corrosive environments. Composite materials such as fiber-reinforced polymers (FRP) can offer performance advantages for construction in these environments. In the last decade, piling made of FRP composites has been used experimentally throughout North America. However, composites face obstacles because they do not have a long track-record of use in civil engineering structures. A comprehensive review of the current experience in research, testing, design, and practice of composite piling is presented in this paper.

Jan 1, 2002

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

By P. Walford, C. Mealin, D. Good

"The geology of the Ore Fault Ni-Cu deposit has been reinterpreted in the light of recent studies of the geology of the Neoarchean Bird River Sill Complex and the occurrence of economic Ni-Cu and Zn-Cu-Ag mineralization. The Ni-Cu sulfides are hosted by the lower of two parallel NNW-trending and moderately W-dipping mafic-ultramafic intrusions related to the Bird River Sill Complex. The bod¬ies intruded a bimodal volcanic suite consisting of weakly deformed mafic flows and felsic pyroclastic rocks. The mafic volcanic rocks are geochemically related to the MORB-type rocks of the Lamprey Falls Formation, and the felsic volcanic rocks are related to arc-type rocks of the Peterson Creek Formation. The original pyroxene- and olivine-dominated mineralogy of the sills has been replaced by variable ser¬pentine-amphibole-talc-carbonate assemblages.The Ni-Cu sulfide assemblage exhibits textures and geochemical signatures typical of orthomagmatic sulfide mineralization. The sulfide minerals are associated with cumulate layers of magnetic ferrochromite that range in thickness from a few to tens of centimeters. A later event of Zn-Cu-Ag sulfide mineralization associated with quartz veining and garnet-chlorite alteration along a fault that strikes north, dips vertically, and cuts all rock types. The mineralized fault is cut by the NE-trending Peterson Creek shear zone. Where the Ni-Cu and Zn-Cu-Ag mineralized zones intersect, remnant magmatic features such as amphibolite or cumulate ferrochromite bands occur within quartz veins or local chlorite alteration. The mixed zones contain a very unusual polymetallic assemblage of Ni, Cu, Zn, Ag, and platinum group elements (PGE)."

Jan 1, 2009

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By A C. Carter

The increasing need for alternative energy sources as well as the less clearly perceived but equally increasing demand for non-fuel minerals has resulted in extensive exploitation of near surface deposits. Many such deposits have depleted reserves and mining corporations are increasingly turning their attention to deposits, with thicker overburden, less competent materials, steeper dips and more complex structure. These deposits pose mine layout, geotechnical and equipment problems as well as the need for large outputs to achieve economies of scale. The paper describes the major problems and operational solutions for such deposits using continuous excavation and transport equipment.

Jan 1, 1980

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

After a snap-shot survey of water quality of streams draining various coal measures carried out in 2000 - 2001, West Coast Regional Council expanded its monitoring programme to better establish the condition of streams draining coal mining areas and to characterise the variability of water quality with respect to stream flow. Samples were collected for water quality indicators such as pH, sulphate, turbidity, conductivity, temperature and dissolved oxygen as well as macro-invertebrates, fish and assessments of stream habitat. Water quality sampling was carried out at 27 sites on 21 streams located from Page Stream near Seddonville in the north, to Seven Mile Creek near Dunollie in the South, and to Garvey Creek east of Reefton. There was relatively low variability of pH, conductivity and sulphate concentrations at most of the sites sampled. Conductivity and sulphate concentrations reduced with increasing flow and pH generally increased. Significant effects on macro-invertebrate and fish populations were identified at several of the sites where water quality sampling was undertaken. Of the water quality parameters tested, macro-invertebrates were mostly affected by pH. Although not sampled directly (conductivity was used as a surrogate) heavy metal concentration may explain some of the variation in macro-invertebrate communities. Three creeks affected by mine drainage were sampled for fish and no fish were present. Fish appear to be more sensitive to acid rock drainage that invertebrates. Using data from this survey and other studies conducted in the region, the total length of stream that is actually or highly likely to be adversely affected by acid rock drainage was estimated at 125 km. This figure is useful as a gauge as to the magnitude of the issue in this region and for setting of priorities for remediation. However, as it is only an estimate based on limited sampling sites, it should be used with caution.

Jan 1, 2003

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By Zuhair A. Nawab, Muhammad A. Al-Marhqun, Mehmet Guney

"The Atlantis-Il-Deep is a stratified metalliferous deposit located along the median valley of the Red Sea at a water depth of about 2200 m. The metal-bearing mud contains sulphides of zinc, copper and iron with significant amounts of silver, gold and cobalt. A variety of oxide, siliceous and carbonaceous gangue material is also present. Long sediment cores indicate that the thickness of the deposit may reach 25 m, but the average kriged thickness of metal-rich sediments is about 11 m.Mining geostatistics was applied to estimate the Red Sea offshore mineral resources. Experimental semi-variograms were computed along 0 ± 180 degrees and then models were fitted to analyze the mineralization phenomenon. Kriging estimates indicate that 696.330 million t of bulk sediments contain 1.891 million t of zinc, 0.425 million t of copper and 3. 75 thousand t of silver. Gold and cobalt contents were calculated from the analysis of solids in flotation concentrates as 47 t and 5368 t respectively. The significant outcome of implementing geostatistics to the Red Sea brine precipitates is not only for the evaluation of metal resources, but it also provides a useful tool in the optimization of selective dredging of appropriate areas to be mined. IntroductionThe discovery and extensive exploration of hot brines and hydrothermal sediments in the Red Sea median valley revealed the fact that the Atlantis-II-Deep is a potentially exploitable metalliferous mud in the economic sense. Sediments in the mineralized deep are composed mainly of oxides, various types of silicates and sulphides with considerable concentrations of zinc, copper, cadmium, silver and gold. The mineral-rich deposit, located at a mean water depth of about 2000 m, has an average thickness of 11 m, and is covered by a brine layer having a temperature of 60°C."

Jan 1, 1988

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By Branagan D. F

The geology of the area studied is briefly described, together with the prospecting methods used in the search for copper, lead, zinc and uranium ore bodies.Four prospects, Mt. Corella, Yanasinga, Lawlor's and Greenmount, which were diamond-drilled, are described in detail and geochemical results are discussed in relation to the mineralization found. Copper anomalies were found wherever intrusive rocks were mapped, and showed a much closer relation to geology and mineralization than did the predominantly lead and zinc anomalies.Geochemical prospecting aids in the overall mineral search programme because of its speed and economy, as it helps to pinpoint areas worthy of detailed geological examination. Geochemical anomalies are a guide to favourable zones but may not indicate the presence of ore.INTRODUCTIONDuring 1953-55 the National Lead Company of New York carried out a search for minerals in an area south and west of Cloncurry (Fig. 1) in rocks of Precambrian age. After reconnaissance mapping, a number of prospects were chosen for closer examination by detailed geological mapping and geochemical sampling, and from these prospects, five sites were selected for drilling.This paper records the salient features of the exploration programme and discusses the geology and geochemistry of four of the prospects-Mt. Corella, Yanasinga, Lawlor's and Greenmount. Practically all the prospects examined showed high zinc "anomalies" or "dispersion" trains. Greta, Mt. Corella and Lawlor's prospects showed some copper anomalies and, to a lesser extent, lead anomalies. In particular, Greenmount exhibited striking copper anomalies.

Jan 1, 1960

By G. F. Kuncir

This volume was prepared in support of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation under a Bureau of Mines contract. The evaluation is described in part within a companion volume entitled Benefit-Cost Analysis. The economic mine models outlined herein provide a quantitative basis for the assessment of program benefits. Reference is made to estimated oil shale mine costs to delineate the beneficial impacts that can be expected to accrue for the future implementation of program developed technology. Estimated mine cost data are provided for surface, underground, and modified in situ oil shale mining operations.

Jan 1, 1977

By William O. Vanderburg

This report3/ gives the reconnaissance of a reconnaissance of the mining districts in Churchill County, Nev., made in the fall of 1938 and spring of 1938 All of the mining districts in the county were visited, but no attempt has been made to include all the mines and prospects within the area; inclusion or omission of a property in this paper has no bearing on its merits, The report gives the situation of the various districts, mineral production, and ownership of properties; describes the ore deposit, mines, and prospects; contains information on past and current activity; and includes other data likely to be useful to those interested in the development of our mineral resources. The various district, were named when they were organized for purposes of record and regulation. When established, the districts embraced large areas n without well- defined borders, so that the names have little geographical significance.

Jan 1, 1940

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

Mount Isa Mines Limited first installed electronic data processing equipment in 1959. The decision to replace this equipment with a computer was motivated by the need for greater processing power and the availability of new and less expensive computers. Consideration of hardware software and delivery features of available equipment, resulted in the selectIon of an ICT 1900 series computer which was installed in March 1966. Special air-conditioning and power stabilization equipment was also required.Systems design and programming was carried out by personnel recruited from within the Company and trained by the computer manufacturer. Early work was hindered by the problems of remote location.Initial applications were basically accounting functions whIch were taken over from the EDP installation. Subsequently computer applIcatIOns of a more complex technical nature have been undertaken. Future work will include both "scientific" and data processing applications.

Jan 1, 1968

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990