Search Documents

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By J E. Moffatt, N A. Spooner, T J. de Prinse, D J. Ottaway, E Klantsataya, L d. S Teixeira, B W. Smith, T B. Payten, G Tsiminis

Single wavelength fluorescence sensing has been used in the preconcentration of ores for many years in situations where it is typically specific to the mineral of interest. Examples of fluorescence sensing include the sorting of diamonds in diamond mines and the sorting of scheelite in tungsten ores. However, the number of minerals that show useful single wavelength fluorescence properties in the visible spectrum is relatively small, so the application of fluorescence sensing is currently limited to niche application in the minerals industry. Recent developments at the University of Adelaide have focussed upon extending fluorescence signal measurements into the infrared spectrum, as well as investigating multi-wavelength fluorescence known as up-conversion fluorescence. These techniques may not only significantly increase the number of minerals that exhibit fluorescence properties suitable for both identification and sensor-based sorting, but also provide mineral-specific signatures of higher quality than previously attainable. This paper details the research work carried out by the University of Adelaide and funded by CRC ORE to develop a mineral-specific fluorescence sensor. The sensor targets two fluorine bearing minerals, fluorite and fluorapatite, that are common in many base metal ores such as porphyry copper ores and silver/lead/zinc ores. Fluorine is a known penalty element in mineral products derived from these ores, so mining companies need to monitor and control the amount of fluorine in their final product to keep it below commercially agreed specifications. Currently there is no real time sensor capable of monitoring fluorine in the ore feed so monitoring and control is carried out using time-consuming standard sampling and off-line laboratory measurements. The development and application of a real time fluorine sensor will enable the mining companies to monitor and control fluorine levels in the plant, greatly reducing the time and cost associated with producing their mineral concentrates within the prescribed specifications.

Nov 10, 2020

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By Hamid Maleki

A novel ground control program has been developed at Plateau Mining Company through five years of geotechnical investigations. The study was initiated to determine the causes for roof stability problems and to develop alternative support and monitoring systems for increased safety and productivity. From systematic roof fall observations, extensive geologic mapping, roof drilling and monitoring ground movements along gate entries of four longwall panels, a sand- stone channel system was detected and shown to impact roof stability. In particular, underlying mudstones up to seven feet thick experienced instability due to differential compaction and load transfer from the gob. Roof bolter operators were trained to report roof lithology for mapping channel positions into the roof and for selective use of longer bolts. This boosted operator morale, and improved ground conditions. Monitoring rates of roof movement is used in these areas for detection of instability and for application of secondary support: This has significantly increased safety and productivity.

Jan 1, 1987

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By L. Boyd, T. Martin, V. Gall

Water infiltration into subgrade infrastructure can cause major impacts on their performance. In addition to damaging the structure, water intrusion leads to deterioration of installations including electrical and mechanical components and in patron discomfort. To remedy these impacts, leak remediation is often carried out to halt water infiltration. Remediation methods include coatings, drainage, injection/stitch grouting, curtain (backside) grouting, and/or internal umbrella systems. Selection of the rehabilitation method depends on the structure’s use, owners’ priorities, its installations, structural conditions, surrounding ground, and hydrogeologic conditions. Since many factors influence the rehabilitation method chosen, a novel holistic approach is undertaken to understand leakage causes and consequences to develop the most appropriate, efficient, and reliable solution to extend the structure’s life. A reconnaissance phase combines geologic, hydrogeologic, and as-built information with detailed digital scans and visual observations to develop a database of existing conditions. This database, called a tunnelband, is used to develop the rehabilitation solution and made part of the contract documents, allowing for an informed bid by specialty contractors. Tunnelband and the preferred rehabilitation system are portrayed in contract documents, which are procured in various contract types depending on the owner’s preference and project characteristics. The pool of contractors are required to submit their understanding of this holistic approach by developing and supplying the owner with a detailed workplan. The completed rehabilitation is portrayed in detailed as-built drawings which also provide the owner with an operation and maintenance manual outlining for periodic observation of the structure and checking of its performance. Ultimately, this information is implemented into a “BIM Digital Twin” that is used by the operations and maintenance staff for long-term observations. This proposed novel framework for leak rehabilitation is currently being used successfully in a number of projects throughout the United States.

Jun 13, 2023

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By R Fox, R Watt

On behalf of ICI's group of explosives companies around the world, a research programme is being undertaken to develop a new electrical shotfiring system which will have markedly improved safety features and operational advantages over existing initiating systems. The paper describes the development of the 'Magnadet' Electric Detonator and 'Magna' Primer and the field experience to date. It also indicates those areas where further work is being carried out on modification of the basic designs to meet specific application requirements.

Jan 1, 1981

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004

By Hilal Soydan, H. Sebnem Düzgün, Jurgen Brune

In this study, with the primary goal of capturing ongoing digital transformation and automation impacts on the mining industry and its workforce, we conduct several interviews with mining industry experts in the United States and analyze our survey reports qualitatively and quantitatively through exploratory analysis. After the interpretation of the insights of industry experts, we proceed to generate a personalized and customized data analysis through a novel metric based on skills, knowledge, competencies and occupational requirements, which quantifies the job similarities for occupations in the mining industry based on the publicly available database of the U.S. Department of Labor. We use text analytics to tokenize and classify the interviews to capture a better understanding of major response categories. The temporal analysis shows that the critical competency needs in the data science and autonomy category increases from 28 percent in current demands to 43 percent. In defining our metric, we also calculate Kullback–Leibler (KL) divergence for each job profile that enables determining whether and to what extent that job is transitionary in our test set based on the mean, standard deviation and kurtosis of each job of interest. Our analysis reveals that the in-group job transitions are significantly easier than the between-group transitions, proving our initial assumptions and common sense. The generated heat maps provide the opportunity to present the gap between the current job and desired job profiles that provide feasible career change options, among others, offering individualized career paths for job seekers and promoting potential job transitions. Through the collection of industry-specific individual employee data, the AI system is envisaged to continue to learn as end users engage with the system, thus creating a central data hub specifically for the future workforce in the mining industry. Although the study has limitations on generalizability for qualitative assessments, it presents itself as a valuable application of how qualitative and quantitative approaches could be of value for future worker training in the mining sector.

Feb 1, 2025

Convential smelting of copper - cobalt - iron sulphide concentrates result in th eoxidation of cobalt and iron, which are subsequently lost into the slag. The emission of SO2 bearing gas from smelting causes serious health and environmentsl problems. In this investigation, three different types of copper - cobalt - iron sulphide concentrates, derived from froth flotation, were investigated, the concentrates, each containing more than 40 wt % percent gangue material, were directly reduced in the presence of lime and corbonin the temperature rnage of 1073 K - 1573 K, fo rthe production of an alloy containing copper, cobalt and iron. We demonstrate the basic principles of process physical chemistry for the recovery of alloy by carrying out a detailed process analysis utilising the predictions from thermodynamic equilibrium and results from the kinetics of reduction reaction. The effect of temperature on the reduction kinetics and alloy formation were determinedand analyzed in detail.

Jan 1, 2012

By R A. Pax, B Cornish

Increasing the throughput of the MMG Century operation by over 25% from past practice to preserve cash flow close to the end of life of mine has revealed new throughput and load dynamic instabilities in the SAG mill causing significant time averaged loss of production. A twelve microphone array around the SAG mill (Pax, 2014) using the non-contact acoustic measurement methodology (Pax, 2011, 2012) has been used to diagnose the new dynamics. Dynamic acoustic noise signal information allows discrimination of the behaviour of the steel balls and the rock. Determination of mill load, toe and shoulder angles, water holdup, and proxies for mill load are possible.The instability was diagnosed with the help of an abnormality in the liners/lifters of the SAG mill with one row of lifters having a slightly increased in-mill life compared to the rest. The steel shoulder angle is observed to be disturbed cyclically at a rate of precisely one revolution at low throughputs of 750 t/h. However, at throughputs closer to 1100 t/h, the cyclic signal disappears indicating additional dynamics to randomise the repetitive behaviour of the mill charge. The cyclic signal has been used to operate the SAG mill with improved stability at 1100 t/h by adjusting the feed water addition rate.This paper presents and discusses these results and proposes the suggested origin of the extra dynamics. A small consistent aberration of the lifters circumferentially provides a useful detector of stable mill operation and a novel sensor for the dynamics of the internal operation of a SAG mill.CITATION:Pax, R A and Cornish, B, 2015. A novel measurement for the internal operation of a semi-autogenous mill using acoustic sensors – a case study, in Proceedings MetPlant 2015, pp 120–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Huimin Lu, Shi Zhou, Lisha Yang

"The Zeolitic imidazolate frameworks (ZIFs) were successfully synthesized by applying a combination of ionothermal synthesis and microwave energies for rapid synthesis. The synthesis was proceeded under various conditions including different raw materials, reaction temperature as well as microwave irradiation time. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are new type of porous materials formed by inerratic polyhedral in three-dimensional. They are the ideal crystalline substances for gas separation and storage. The assynthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA) and C02 adsorption test. Results illustrated that the synthesized samples had stable structure, high thermal stability (up to 530 °C) and C02 adsorption capacity (10.2 cm3/g at 0°C under ambient pressure). This novel method also showed great advantage with high energy efficiency, safe synthesis conditions, and rapid crystallization time (60 minutes).IntroductionNowadays, carbon dioxide capture has become imperative due to the global warming caused by the increase of C02 in the atmosphere, especially produced by the concentrated sources such as power plants [1]. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are ideal crystalline substances for gas separation and storage due to their structure diversity, high thermal and chemical stability [2-5]. They are formed by inerratic polyhedra in threedimensional with large cages and small apertures. Traditionally, ZIFs are synthesized by solvothermal method in a sealed autoclave under autogenous pressure [6-9]. However, in order to generate the products, the solvothermal temperature should not be lower than 100°C according to the sovlothermal mechanism. Moreover, at such a temperature, molecules with a low boiling point (such as water) may generate high pressure in reactor which might cause danger [9]. Thus the synthesis requires the equipment to possess resistance to autogenous pressure and corrosion. Further, conventional solvothermal methods need a long time to prepare products, usually a few days, which is a large energy consumption and inefficiency. So it is interesting to synthesis ZIFs through other ways under mild reaction condition with high energy efficiency."

Jan 1, 2012

By Stuart Hardy, Xiangbo Qiu

The South Bank Place project comprised the redevelopment of the iconic Shell Corporation headquarters in Waterloo, located on the Southbank of the River Thames in central London. The site was originally developed in the 1950’s and due to the monitoring of the underlying Bakerloo Line tunnels by the Building Research Station it has become a seminal case history for the long term swelling behaviour of London Clay. The redevelopment, undertaken by a joint venture of Canary Wharf Group and Qatari Diar, included demolition of the existing building (with the exception of the main towers) retention of the existing basement structure and the construction of eight new mixed use buildings, up to 31 storeys in height. The foundations for the new buildings varied according to the building height and the below ground constraints. Two of the buildings are partially founded in reused under reamed piles that were installed as part of the original 1950’s development. The paper describes the novel methodology developed to assess the re-use of the under reamed piles which builds on the guidance published by CIRIA and the BRE for straight shafted piles. The paper also describes the physical investigations and numerical analyses undertaken as part of the assurance process and the procurement of latent defect insurance by the client.

May 1, 2022

By M. Saghaeian, R. Hejazi, Fakoor Sanat Tehran Company, H. Abedini, M. Zare

"Dewatering of final tailings is one the biggest issues in iron ore processing plants. Because of the fine and hydrophilic particles in the iron ore tailings, dewatering of such material is difficult and, in most of the cases, needs to be processed using expensive and complicated equipment. In this study, a novel method based on classification of small and large particles has been proposed to improve the dewatering performance of iron ore tailings. In the proposed method, a hydrocyclone has first been used to separate the fine and coarse fraction of iron ore tailings. Then, the coarse fraction (hydrocyclone underflow) is easily dewatered by using vacuum belt filter. Then, the fine fraction (hydrocyclone overflow) is primarily dewatered by using a high rate thickener. Finally, the thickener underflow is added to the bed of solids on the same belt filter, which is used for dewatering of hydrocyclone underflow. The efficiency of this method has been compared with other solutions for tailings dewatering including changing vacuum filtration parameters, using fabric with larger pore size, and using pressure filtration, all through laboratory scale experiments on the tailings of an iron ore processing plant in Iran. The results indicated the superiority of this method compared to the other ones, which increased the specific filtration capacity of the tailings by around 46%.INTRODUCTIONWet beneficiation of minerals requires a substantial amount of water to enhance the efficiency of the process. Used water should be recovered at the end of process to minimize shipping costs, meet contract specifications, and reuse process water (Wills and Napier-Munn, 2006). Dewatering equipment is usually divided into sedimentation (thickening) and filtration (pressure and vacuum) equipment, the choice of which depends on particle size, solid content of slurry, and material nature (Mular et al., 2002)."

Jan 1, 2016

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993