Search Documents

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981