Search Documents

By Yan. T. Y.

Uranium precipitation from an eluate using hydrogen peroxide has been studied in a laboratory continuous unit. The important process parameters were the dosage of H2O2, reaction pH and chloride ion concentration. In the process, the alkaline eluate is acidified to a pH of 2, then H2O2 at 110%-130% of the stoichiometric requirement is added, and finally NaOH is added to maintain a pH of 4 for one hour to complete the precipitation and settling. The chloride content in the system is controlled to 50g/L or below by rejecting part of the decant solution. The process has been successfully employed in commercial operations. The uranium recovery is complete, while the precipitate settles rapidly and can be processed to high purity yellow cake without filtration.

Jan 1, 1991

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth's crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974

By Julia Herhold

The demand for sustainable and profitable/efficient projects within the tunneling and other underground engineering sectors grows rapidly. Construction tasks play a key role within the project conduction, whether as primary (tunneling), secondary (e.g., mine securing) or tertiary processes (e.g., workshops). The construction tasks of primary processes create the main structures, such as tunnels, which resemble the main project goal. For the secondary and tertiary processes, the purpose of the task shifts. The main goal is to provide structures, such as the securing of the cavity and workshops, that enable the project and enhance the efficiency of the primary conduction underground. To plan and optimize the conduction of construction tasks underground, whether they are identified as primary, secondary or tertiary tasks, the work preparation can be used. This method, known from the above ground construction, can be adapted and used underground. The approach of a digital work preparation tool combines, connects and adapts the main tasks “choice of procedure,” “logistics” and “site planning.” In addition, the digital tool is connected with digital models (construction, site, surroundings). With the adaption and forward projection of the work preparation, underground constructions (e.g., tunneling) can provide a more sustainable and efficient outcome.

Jun 13, 2023

By J. David Gunn, Richard W. Lawrence

Gold and silver often occur finely disseminated in sulphide minerals such as pyrite. The use of biological leaching to dissolve pyrite and liberate gold has been extensively studied for a concentrate from the Porgera deposit, Papua New Guinea. The successful operation of a continuous bioleach circuit has been demonstrated. Bioleach residues were cyanide leached to extract gold and silver, and unreacted pyrite recovered for recycle to the bioleach. A 26 day steady state continuous bioleach test on a concentrate assaying 14.3 g/tonne Au and 87.0 g/tonne Ag produced residues with an average 73.5% weight loss and a pyrite oxidation of 88%. Cyanidation and recovery of pyrite from the cyanide residues for recycle gave overall recoveries of 92.1% gold and 74.6% silver. A proportion of the remaining precious metals was found in the bioleach solutions and may be recoverable. Losses to tails were 3.0% gold and 8.1% silver. Final tails represented 14.3% of the feed weight and averaged 1.84 g/tonne Au. A description of the continuous bioleach circuit and bioleach residue handling procedures, and the results of the study are presented. The features and advantages of biological oxidation as a pretreatment for refractory precious metal ores and concentrates are discussed.

Jan 1, 1985

By E. I. Jurgens, K. E. Hanney, D. C. Comrie, R. H. Fletcher

Introduction The reclamation of mine/mill tailings areas is undertaken for a variety of objectives including safety, appearance, economical use of lands and forests and long term storage of a future resource. The establishing of criteria for these objectives at any site is a shared task of the government and mining company. Our attention in this paper is directed to uranium mine/ mill tailings as they are handled in the Canadian industry and in the unique Canadian climate. We focus our attention on the state of the art. Uranium is a ubiquitous mineral forming an average of 4 g per tonne of the Earth's crust. Ores are mined at about 500 g per tonne so that the residual content of uranium in tailings is comparable to average background levels. However, as in most mine/mill operations, the ore contains other minerals that become readily mobile after milling operations. Thus the main objective of tailings impoundment is the stability both physically and chemically of the mobile materials. Since the requirements for the operation and construction of tailings areas in Canada have changed considerably over the past decade, there exists a great many mine/mill tailings areas which while considered adequate in their day, would not meet modern criteria. However, most of these installations pose no concern or hazard to the public. The proximity of mine/mill development to inhabited land areas has necessitated more stringent modes of tailings operations and provisions for tailings site reclamation. The more important of these have been: 1) the prevention of dyke failure, with large liquid-solid outflows onto adjoining lands, and 2) the prevention of seepage from the tails of pollutants such as chlorides, sulphides, heavy metals and radionuclides. Uranium mill tailings are discharged as a slurry from the concentrator after the removal of generally only about 1000 g, or less, per tonne of uranium from the as-mined ore. As a consequence, a great volume of low level activity waste is generated. The amount of tailings is expected to grow in quantity in the future even faster than the increase in yellowcake production, as the demand for energy

Jan 1, 1980

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By Nikhil Dhawan, Sanjay Pindar

The limited lifespan, ever-growing demand, and significant lithium and cobalt content are responsible factors for the immediate recycling of discarded lithium-ion batteries. Discharged batteries were dismantled, segregated, and size reduced to recover cathode and anode material. The active cathode material comprises LiCoO2 (65.8%) and LiMn2O4 (34.2%) and was carbothermal reduced with recovered graphite in a microwave furnace followed by water leaching and magnetic separation. A Box Behnken statistical experimental design is used for process optimization. Both cobalt and manganese report to magnetic fraction, whereas graphite and lithium carbonate report to non-magnetic fraction and solution crystal respectively. The final product comprises of cobalt 73% and manganese of 14% with process yield of 36% and saturation magnetization of 76 emu/g.

May 16, 2020

By Bhaskar B. Thapa, Michael T. McRae, Johannes V. Greunen

This paper describes the preliminary design of the fourth bore of the Caldecott Tunnels along State Route 24 in Oakland, California. The paper focus is on two major aspects of the project: initial support system design and seismic design. The initial support system was designed based on the New Austrian Tunneling Method (NATM).NATM provides the required flexibility to accommodate the variable ground conditions in the weak, folded, and faulted rock along the alignment. The seismic design provides a final lining system that meets serviceability requirements for a 1,500 year seismic event with an estimated peak ground acceleration of 1.2g.

Jan 1, 2007

By W. S. Fyfe, G. Southam, T. J. Beveridge

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An invitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold(which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14%within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%)throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

A study was undertaken to determine the effects of five industrial frothers on the relationship between entrainment recovery and water recovery. The experiments were conducted using a Batequip rectangular 60L steel flotation cell that was run in parallel with the first cell in a copper/silver prefloat rougher circuit. The concentration of the frothers ranged from 2.5 to 8.4 g/t. The experiments were repeated at three different froth depths. A power function was found to fit this relationship with no discontinuity in the relationship caused by the changes in frother type and concentration and froth depth.

Jan 1, 2002

By D. W. Carson, R. J. Trembley

Thoron daughter WL&apos;s measured by alpha-spectroscopy and the Kusnetz method are about one-half those of radon daughter WL&apos;s in a uranium mine in Canada.1 A diffusion model can account for the relative concentrations.l Since the Kusnetz technique is most widely used for measuring radon daughter WL&apos;s in uranium mines, a general procedure is derived to extend this method to measurement of WL&apos;s of radon and thoron daughters in air containing their mixtures. Coté P. and Townsend M.G., 1981. A procedure is also suggested for counting radon and thoron daughters by 3-channel [a]-spectroscopy. Errors in WL(Rn) are calculated for standard radon daughter counting procedures when a-decay of both thoron and radon daughters is attributed to radon daughters alone. Providing overall counting times are short, [<]30 min, these errors are generally small. The precision of ß -counting methods is also investigated. A portable 3-channel alpha spectrometer for measurement of radon and thoron daughters in uranium mines or homes is described, Carson D.W., 1979. The computer programs for analyzing the data to give, depending on the mode employed, some or all of the concentrations RaA, RaB, RaC, ThB, ThC and WL of radon and thoron daughters by alpha spectrometric, modified Kusnetz, Rolle and Tsivolglov methods are presented.(l) A commercial apparatus, based on the above prototype, incorporating a microprocessor and built under contract to EMR is now available.(2) A number of personal radiation dosimeters for miners are now being tested in mines. One of these is the CEA dosimeter which uses the track-etch film method, Duport P., Chapuis A.M. and Pradel J., 1979. An apparatus for rapid reading of track-etch films by the spark technique has been described previously, Cross W.G. and Thomasino L., 1970 and Huang V.F., 1975. We have developed such an apparatus for rapid semi-automatic reading of films exposed to radiation from mixtures of radon and thoron daughters in CEA dosimeters. The films used, Kodak LR 115 Type II Strippable, may be stripped rapidly and easily, for counting after irradiation and developing, by use of a special punch and suction technique. The method promises to provide an inexpensive and rapid technique for reading large quantities of personal dosimeter films. However, the present CEA dosimeter has faults in design, leading to a contamination problem. Those films that show contamination cannot be read by automatic means. A commercial apparatus based on the above prototype spark counter and built under contract to EMR is now available.3 1. These computer programs are available on request. 2. Pylon Instruments, Ottawa 3. Bondar Clegg, Co. Ltd., Ottawa. REFERENCES Carson, D.W., 1979, "Canalph-3, a Portable Three-Channel Alpha-Spectrometer for Measuring the Daughter Products of Radon and Thoron", CANMET Division Report MRP/MSL 79-108 (TR). Coté, P. and Townsend, M.G., 1981, "Mixtures of Radon and Thoron Daughters in Underground Atmospheres", Health Physics, Vol. 40, pp 5-16. Cross, W.G. and Thomasino, L., 1970, "Rapid Reading Technique for Nuclear Particles Damage Tracks in Thin Foils", Radiation Effects, Vol. 15, pp 85-89. Duport, P., Chapuis, A.M. and Pradel, J., 1979, "Appareil Individuel pour lu Dosimetrie des Descendants du Radon", Advances in Radiation Protection Monitoring, IAEA Vienna, pp 435-443. Huang, Y.F., 1975, "Determination of Uranium in Minerals using Fission Tracks", M. Sc. Thesis, University of Toronto, 48 pp.

Jan 1, 1981

By M. L. W. Tuttle, B. R. Berger

Our study focuses on the geology, hydrology, and geochemistry of a variety of molybdenum (Mo) porphyry systems. The systems are either high fluorine, granite, Climax-type, systems (e.g. Mount Emmons/Redwell Mo deposit, Colorado and Questa Mo deposit, New Mexico) or low fluorine granodiorite systems (e.g. Buckingham Stockwork Mo deposit, Battle Mountain, Nevada and Cannivan Gulch Mo deposit, Montana). The water quality of streams, natural springs, mine discharge, and ground water from drill holes were assessed in the region of these deposits. The ultimate goal of our study is to understand the environ-mental behavior of these Mo porphyry systems in the context of geologic setting, hydrologic regime, and climate.

Jan 1, 2004

By V. Canby

Introduction Located in Russia’s Chukotka Autonomous Region near the Arctic circle and 425km from the seasonal port of Pevek (population approximately 4600), Peschanka (or ‘Anyui’) is perhaps the world’s most isolated CuMoAu porphyry deposit of significant grade and tonnage. In addition to its extreme remoteness (66°36&apos;N/164°30&apos;E) and lack of developed infrastructure, Peschanka is located in one of the world’s coldest regions, with annual average temperatures well below freezing. Soviet exploration up to 1985 defined four zones with inferred resources of roughly 940Mt @ 0.51% Cu, 0.42 g/t Au, 1.4 g/t Ag and 0.019% Mo (1).

Jan 1, 2007

By J. J. Moore

Combustion synthesis, or self-propagating high-temperature synthesis (SHS), reaction systems are discussed with respect to thermodynamics and kinetics. In particular, the effect of the process parameters, e.g. particle size, [All] ignition and combustion temperatures, on these self-sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall actuation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti-X intermetallic shape memory alloys, TiC-AI2O3 and ZrB2-AI203 ceramic composite materials.

Jan 1, 1992

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By Jeffrey P. Carstens

INTRODUCTION Thermally induced fracture of rock is one of the oldest rock breakage techniques known to man. Primitive underground miners used fires to heat and crack rocks as early as the third century B.C. (Ref. 1). History aside, however, present-day tunneling and mining interests are reconsidering the use of modern heating units for rock fracture for some very good reasons. One of the most important advantages of many heating techniques is the lack of direct contact between the heating device and the rock. This means a lower wear rate relative to mechanical cutters, and no large reactant force to be supplied by the tunneling machine. In addition to avoiding physical contact, some heating systems (e.g., electron-beam guns and lasers) can deliver energy to a rock face much more intensely than can be conveniently handled mechanically. Thus, heating power densities of the order of lob to 107 watts/in.2 and greater can be achieved with high-power lasers. These high power levels allow much higher instantaneous penetration rates than can be achieved by mechanical cutting. Another advantage that accrues to some thermal techniques, such as, for example, surface spalling, is that the thermal fracture process works particularly well in certain rock types (e.g., granite) that are particularly hard to cut mechanically. Other methods, involving high power density, are able to cut any rock type, and are relatively

Jan 1, 1997

By Randal J. Barnes, Franck Rellier

Mine ventilation survey data includes generally redundant, usually inconsistent, often incomplete, and always noisy measurements. Yet, these data are essential for operational decisions and represent the foundation of any mine ventilation systems model used for future engineering analysis and design. For example, the basic ventilation network geometry can be measured with a reasonable precision, the network flows can be measured, but with significant errors, and the branch resistance factors can not be directly measured at all. The network-based, constrained weighted least squares approach, presented in this paper, advances a method for the sys tem-wide adjustment of ventilation branch measurements and the consistent estimation of global system parameters (e.g. branch flows, head losses, and resistance factors). The constraints guarantee that the adjusted values satisfy the governing physical laws: conservation of flow, conservation of energy, and the appropriate energy dissipation rule (e. g. Atkinson&apos;s RQ2). The weights allow for the proper inclusion of data with widely disparate precision, as well as offering a simple method for retiring old data as the mine changes through time. The post-adjustment sensitivity analysis presents two potentially useful forms of analysis: the identification of previously unspecified leakage branches, and the semi- automatic recommendation for future ventilation measurement campaigns. The overall efficiency of the algorithm is exemplified by the fact that a ventilation network with hundreds of branches and thousands of measurements can be routinely adjusted on a microcomputer.

Jan 1, 1989