Search Documents

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981

By Giuseppe Gaspari, Xiangrong Wang

The pandemic emergency is forcing transit agencies to define strategies allowing social distancing, which are more challenging in underground interchange stations in crowded downtown cores. Toronto Transit Commission’s (TTC’s) Bloor-Yonge Station Capacity Improvement Project in Toronto was approved to meet increasing demand and represents an opportunity to fight COVID-19. This paper discusses cost-effective solutions in expanding the cut-and-cover station box over the existing Toronto Subway Line 2 and connecting it through ventilation openings in the cast-iron tunnel liner. Potential uplift risks and structural damage due to minimal vertical clearance were analyzed via three-dimensional finite element analyses with advanced constitutive laws to simulate the multi-stage construction process. Based on the simulation results, a series of countermeasures, including excavation support systems, king posts, ground-consolidations, and liner reinforcements were integrated into comprehensive design options to ensure the serviceability and structural integrity of the subway tunnels.

Jun 13, 2021

By Y. Luo

Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for predicting, the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface movement data, a relatively large portion of the subsidence data collected could not provide more information other than surface movement. In this paper, the sources and magnitude of errors in the measured surface movements and calculated surface deformation are discussed. Techniques for improving the accuracy of the calculated deformation indices (i.e., slope, strain, and curvature) are developed. The proposed techniques include: (1) proper selection of monument spacing for subsidence monitoring; (2) a data smoothing technique for data pre-processing; and (3) a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data.

Jan 1, 1992

By Numan Elmas

Barite deposits located in Dinek and surrounding region have important economic features with their large reserve capacity for Turkey. The objective of this study is to elucidate geological and depositional characteristics in terms of. site investigation and chemical analysis. In order to do this, geological area of about 300 km2 was examined and detailed geological map was constructed. It was observed that Barite mineralization in these deposits was occurred in carbonate and pelitic rocks of Lower Cambrian-Lower Ordovician. Deposits were exposed to advanced diagenesis regional metamorphism and tectonics that rotated and deformed the barites; therefore, barites shows secondary veins, brecciate and fracturing structure. Even though, a few light isotope values of barites may suggest hydrothermal and exhalative sedimentary characteristics or possible mixing with magmatic fluids, generally heavy isotope values indicate that the sulfate ions were supplied from coeval seawater and, many of sedimentary features and petrological, geochemical characters support dominantly sedimentary origin.

Jan 1, 2005

The Peruvian mining industry has seen an explosion of foreign investment since President Albert? Fujimori's government was first elected in 1990. Since then, Peru has taken some large steps toward recovery, making it the envy of most other developing countries. A measure of political stability was gained in 1992 when Shining Path leader Abimael Guzman was captured. In addition, the country has taken on a huge privatization program, rewritten its foreign investment laws and has reined in its annual inflation rate from 1,700% in 1990 to about 8% by late 1997. Small wonder then that attendance at the XXIII Peruvian Institute of Mining Engineers conference reached a record level, many of whom are employed by some of the world's largest mining companies. About 2,700 mining industry professionals from all over the world attended the week-long event, held in late September in Arequipa. That was an increase from 1995s 1,600 attendees, that meeting also held in Arequipa.

Jan 1, 1998

By Edward L. Mooney

In the, West, walking draglines often offer the least cost method of uncovering coal for surface mines. However, with each of these machines costing millions of dollars, a good deal of analysis can be justified by the potenial savings or, conversely, costs associated with the choice of a machine. This has resulted in the recent development of a number of computerized models for dragline selection and pit design. One of the earliest reported models for this purpose was developed by Dunlap and Jacobs (1). Later, Rumfeldt described the computer approach to sizing stripping draglines given the required production rate and mine site parameters (2). This basic approach is probably still the most widely used with models for more complicated mining methods reported by Stefanko, Tomica, Finch, as well as others (3,4,5). furthermore, detailed simulation models useful in this regard have been developed by McDonnell Douglas and Fluor, Utah (6,7)

Jan 1, 1982

Surface characterization techniques, i.e. contact angle measurement, atomic force microscopy (AFM) surface force and surface imaging measurement, were applied to investigate the molybdenite surface in aqueous solution. It was shown that the cleaved basal surface of molybdenite was very hydrophobic with a 92 degree water contact angle. The non-polar component of the solid surface free energy is 50.52 mJ/m2 while the polar components are almost zero. The solid surface was not reactive and was only weakly charged at the pH 6. When the aqueous media changes from water to 1×10-4 M KEX solution, the measured contact angle, adhesion force and surface roughness all increase slightly. However, ethanol rinsing made the surface change back to the bare substrate. It was suggested that the hydrophobic chemical, i.e. dixanthogen, which was shown in the morphology of patches by the AFM image, physically adsorbed on the hydrophobic molybdenite surface through the hydrophobic interaction.

Jan 1, 2009

By J. M. Applegate

In the same way that a blueprint communicates information about a structure, a useful systems architecture should provide information that guides the construction and implementation of computing systems. Taking the blueprint analogy a step further, a plot plan can also show where in the "bigger picture" a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: 1. The primary purpose of computer based systems relative to particular task or operation. 2. The relationship of systems to each other and an indication of their interaction and dependencies. 3. The relationship of systems relative to the organization and its objectives. 4. Indications of where IS/IT resources can best be allocated to support the organization. 5. The overall context in which new systems and technologies can be assessed for both their impact on current system and on the organization itself.

Jan 1, 1998

By Philip D. Lindahl

The US Bureau of Mines (USBM) began research to improve the safety and efficiency of transporting coal from underground coal mines using a balanced air-lift hydrohoist (ALH). ALH includes a U-tube pipeline that can be installed through an existing shaft or two surface-drilled holes connecting the mine level to the surface. Bench- and pilot-scale models were tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a riser pipe by injecting compressed air microbubbles. A prototype injector was developed that continuously compacted -50-mm (2-in.), run-of-mine coal in a screw feeder and injected a thick coal slurry into ALH. Initial production rates of 40 t/h (44 stph) through a 200-mm-(8-in.-) diam riser pipeline were achieved with a50-m- (165-ft-) high pilot-scale model. The potential productivity was expected to increase to 100 t/h (110 stph) through modification of the coal injector.

Jan 1, 1995

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By C. H. Rawlins

Deep bed media filtration is used as a tertiary treatment step (after hydrocyclones and flotation cells) to remove fine oil droplets and solids from oilfield water before reinjection disposal or to remove particulate material from surface waters used for waterflood injection. Oil and solids injection requirements are typically <5 ppm concentration at <2 micron diameter. The preferred media for produced water filtration is walnut or pecan shell, however the use of this media has evolved by trial & error and the fundamental mechanisms that occur during separation and media cleaning have not been investigated. A project was initiated to fill in this knowledge gap by analyzing the physical, mechanical, chemical, and hydrodynamic properties of six types of granular filtration media (12/20 mesh size): garnet, silica, anthracite, pecan shell, English walnut shell, and black walnut shell. Comparison of bed packing, oil wetting, attrition resistance, particle strength, and fluidization has led to an understanding of the preferred filtration media for separation of fine oil droplets and solids.

Jan 1, 2010

By S. Chander, A. Briceno

The properties of surface films on pyrite have been studied through electrochemical techniques of cyclic voltammetry and AC impedance, measurements. The characteristics of the surface films depend on the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance, showing a certain degree of passivity. Some pyrites show more passivation than others, however. On oxidation, meta- stable phases of Fe(OH)2 and Fe(OH)3 form that transform to more stable phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics that is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide because it is hydrophilic. This study has also demonstrated that AC impedance ,measurements can be used to study the growth characteristics of films at mineral/solution interfaces.

Jan 1, 1988

By Ross W. Smith, Salim Akhtar

Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collect- ors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner(SPL) is obtained at the end of the pot&apos;s life. The SPL contains small amounts of cyanide and fluoride, which present environmental problems. Spent potliner could possibly be used as a fluidizer to replace calcium fluoride (CaF2) in the iron- and steelmaking industry and in the glass industry. A low viscosity and a low melting point are prime requirements for such an application. In the present study, viscosity measurements were performed. The effects of various additives, such as sand, limestone, dicalcium silicate dust and MgO baghouse dust, on the viscosity of SPL were studied. The results showed that the addition of sand and limestone can produce a very high fluidity SPL melt at significantly lower temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 2002

By Yuting Xue, Gamal Rashed, Zoheir Khademian, Connor Brown, Khaled Mohamed

Ground falls in U.S. underground coal mines can lead to significant consequences, including loss of life, injuries, damaged equipment, and production stoppage. Improving the safety of the workplace is of utmost importance for mine workers and the U.S. economy. The Mine Safety and Health Administration (MSHA) accident/injury/illness dataset provides short narratives for reported incidents, including ground-falls. The main objective of this study is to develop a framework that includes: 1) utilizing machine learning algorithms to categorize ground-fall incidents from narratives based on the main cause of the occurrence and 2) demonstrating an example of a user-friendly visualization to display injury/fatality trends from narratives in U.S. coal mines between 1983 and 2021. The developed framework was tested on a subset of the data and achieved an average F1-score of 96% in categorizing the incidents. The outcome will help identify areas requiring additional research and innovative solutions to reduce severe occupational hazards.

Feb 1, 2024

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

An investigation into the source mechanism of mining-induced seismic activity plays a vital role in understanding the various modes of failure observed in the underground deep-level South African mining environment. The seismic events data for this study was captured by the mine-wide seismic system operating at Kloof Gold Mine. This system comprises 40 4.5 Hz tri-axial geophones sampling at 6 kHz installed at locations that surround the stopes mining the Ventersdorp Contact Reef (VCR), Main Reef (MR) and Kloof Reef (KR). A set of 103,753 mining-related seismic events (-3.0≤ ML ≤2.7) that occurred during 2017 and 2018 was selected for this study. The mining depth of these seismic events ranges from 1600 – 4200 m; most located close to stopes mining the VCR ore body. The main criteria used to select a subset of events for detailed analysis were the number of stations that recorded the seismic event and the azimuthal distribution of the sensors.

Apr 26, 2022

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974

By Charles Dr. Li, John Dr. Box

Selective flotation and adsorption behavior of zircon and rutile under hot soap conditions have been examined. Conditioning temperature, pH and washing steps were shown to control the flotation selectivity. The adsorption of the sodium soap of oleic acid at zircon- water and rutile-water interfaces was investigated through micro- electrophoresis and adsorption density measurements. The soap adsorption on the zircon surface increased markedly with increasing temperature due to a strong chemisorption/surface reaction, and was almost independent of pH. In contrast, the soap adsorption on rutile decreased at high pH values. A simple physisorption plus hydrophobic interaction appeared to be the principal mechanism for the soap adsorption on rutile at moderate temperatures (below ~70(C), beyond which it may change to chemisorption through an activation process. Water wash, particularly under acidic conditions (pH 2-3), of the rutile particles treated with soap, will lead to a desorption of the soap from the rutile surface by forming an acid salt precipitate.

Jan 1, 1995

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000