Search Documents

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By B. F. Buie

In South Carolina and Georgia an area about 20 miles wide situated near the inner margin of the Coastal Plain and extending from the vicinity of Columbia, S.C. southwestward about 180 miles to the vicinity of Macon, Georgia is the principal kaolin-producing area of the world. It is especially important as the world's major source of clay used for paper coating. Essentially all of the land known or likely to be productive of quality kaolin in this area is now owned or controlled by producing companies. The least-fully developed portion is that in the vicinity of Wrens, Georgia which has been explored and developed since 1961. For the two decades following the end of world war II, demand for kaolin increased at approximately twice the rate for other industrial minerals. From 1945 to 1965 production increased four-fold. Since 1965 the rate of increase has been less, but the outlook now is that production and demand will double at least once again before the year 2000. A substantial part of this increased demand has come, and will continue to come, from industrial development, especially in the paper industry, outside the United States. The general effect, in addition to a continuing increase in production in the U.S., will be to cause: 1. Intensive research for development of more effective and more economical methods of beneficiation; 2. Concerted research effort to find an economical way of modifying high-viscosity kaolin so that it can be used for paper coating; 3. More active exploration in the U.S. and overseas, especially for deposits to supply the foreign markets; 4. More intensive study of the geological factors responsible for the accumulation of commercial deposits of kaolin; 5. Some modest rise in price, relative to the cost of other industrial minerals. The effect on kaolin producing region of Georgia and South Carolina will be to cause: 1. Working of progressively lower-grade deposits; 2. An increase in the acceptable thickness of overburden; 3. Mining of deposits farther down-dip, the use of which is now inhibited by large volumes of groundwater; 4. Increased threat of invasion of the kaolin in industry's market by substitute materials; 5. A substantial increase in concern over environmental factors; 6. More attention to be paid to the large opportunity offered for mining of silica sand and other co-products.

Jan 1, 1972

By B. Waterman, R. Collins, V. R. K. Paruchuri, P. Gonzalez, H. Dijkman

"INTRODUCTION Mining and processing of sulfide ore bodies has the potential to solubilize sulfate. Gypsum in the host rock, as well as oxidation of sulfides during milling and processing can solubilize sulfate. Acid rock drainage (ARD) also has the potential to generate waters high in sulfate. Even after treatment of the ARD with lime, the treated water can have sulfate present in gypsum saturation levels. Most mine-sites reuse sulfate impacted water but as a mine nears closure, reuse options may be limited and water treatment becomes an option. Furthermore, sulfate discharge requirements, particularly for anti-degredation narrative standards, can be very strict. Freeport has investigated many new technologies to economically remove sulfate from these types of water. A Dutch company, Paques B.V. developed one of these technologies and it utilized biological reactors to convert sulfate into elemental sulfur in a 2-step process. In 1992 the first industrial reference of the SULFATEQTM technology was commissioned at the Nystar Budel zinc refinery in the Netherlands. PILOT PLANT TECHNOLOGY AND DESCRIPTION As shown in Figure 1, the plant contains several process steps, which can mainly be divided into the following sections: 1. Anaerobic biological system in which sulfate is reduced to hydrogen sulfide by sulfate reducing bacteria. 2. Aerobic biological system in which hydrogen sulfide is oxidized to elemental sulfur by sulfide oxidizing bacteria. 3. Solid/liquid separation in which sulfur, calcium carbonate and biomass solids are separated and dewatered. Sulfate impacted ground water is pumped to the feed water tank through a plate and frame heat exchanger to maintain the solution temperature around 95°F. A custom mix of micronutrients is dosed to the feed tank. This nutrient mixture provides essential elements for the growth of anaerobic and aerobic biomass. Urea is added to the feed tank and provides the required nitrogen source to the biomasses. The pretreated feed water is pumped into the anaerobic reactor. The reactor works on the gas lift principle. Sulfate reducing bacteria utilize hydrogen gas as electron donors and reduce sulfate to hydrogen sulfide. This reaction increases the alkalinity of the solution. Carbon dioxide gas is added in order to control the pH within working range of the reactor. Due to the low solubility of the hydrogen gas, the anaerobic gas mixture is recycled through the system. The gas mixture recycle also provides the gas lift for mixing within the anaerobic reactor."

Jan 1, 2016

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By M. C. Stuttle

MDL Rock Lasers has undertaken successful mapping trials of abandoned mine workings using its underground cavity scanning system. The work was being performed for Kalgoorlie Consolidated Gold Mines (KCGM), Australia's largest gold producer. MDL Rock Lasers supplies underground surveying systems to the mining and quarrying industry KCGM's Fimiston Super Pit, located in Kalgoorlie, Western Australia, is Australia's largest open-pit gold operation. Fimiston's final pit design is expected to be 3.7 km (2.3 miles) long, 1.5 km (0.9-miles ) wide and 540 m (1,770 ft) deep. During the early days of Australian mining, underground operations were labor intensive. Mining was selective and generally narrow stopes were mostly backfilled. Improved processing technology and mine mechanization during the 1970s and 1980s has permitted larger scale operations to adopt less selective underground-stope operations. The "super pit" concept was a logical step for mining companies working toward economies of scale. However, the industry recognized that there was no precedent for excavating a 500-m- (1,640-ft-) deep open pit through ground previously affected by old workings. To appreciate the geotechnical challenge facing KCGM, it is necessary to consider that under the pro¬posed area at the open pit, stoping reached a level of 1 km (0.6 miles) and was supported by more than 2,000 km (1,240 miles) of development headings. The company was fortunate because plans were available for the Golden Mile underground operations. The existing plans were interpreted by the mine's geotechnical team and computer models were constructed of the underground workings. These models can be imported into three-dimensional mine planning packages, such as the Vulcan's Unix-based software, Envisage, to assist analysis and design. This prior knowledge of the workings provided the focus for investigating and confirming ground conditions using probe drilling. After several iterations of drilling, followed by detailed analysis, several decisions were made relating to the nature of the ground and the mining approach to be taken. It was recognized that the stope models were not perfect due to hu¬man error, lack of original survey information and progressive deterioration in ground conditions. It also became apparent that the sole reliance on probe drilling was inefficient in terms of time and quality of information. This was particularly true in complex areas where stopes are in close proximity. A major concern was the presence of open stopes (voids). In many cases, stopes consist of combinations of filled and void sections. The condition of pillars within these underground workings is extremely important. In time, pillars collapse and voids will propagate in upward and lateral directions. So systems needed to be developed that allowed rapid and accurate verification of ground conditions. KCGM was introduced to MDL Rock Lasers while investigating technology for underground mining. The two companies decided to use the C-ALS, MDL Rock Laser's underground laser, cavity scanning system, to improve the management of mining through affected ground. This system was to be used in conjunction with probe drilling and void mapping activities. A field test in one area of the Fimiston Mine verified the capability of the C-ALS system to quickly and efficiently assist in this decision making process. The C-ALS scanner features lightweight, carbon fi¬ber alignment rods from Measurement Devices Ltd.'s (MDL) Boretrak MKII. This is a borehole deviation system that stops the two axis measurement head rotating and lowers the system down a borehole. The scanner is deployed by a 110-mm (4.3-in.) borehole, up, down or sideways. The operator can then carry out vertical and horizontal plan section scans at any user specified ARC (an angular increment of 2°) or the distance between two points on the ARC (CHORD) increments. Windows '95 software enables the operator to control the cavity scanner remotely, surveying the area in real time. The system makes data quick and convenient.

Jan 1, 1999

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By Jorgen Elbrond

The calculation of open pit operations' capacities has been the subject of many studies using computer simulations. The common problems of simulation are that if one desires a realistic picture of an operation the programming work becomes long and expensive and that the program requires a large computer and long time to run. The method presented in this paper overcomes these problems by using a straightforward calculation procedure. It is based on the queuing theory's simple formula for waiting time in a closed circuit and uses a system of correction factors, which reflect the loading, travel, and dumping times' relative variabilities and which have been found by 1) mathematical analysis and 2) simulations of basic circuits. The method includes the main parameters of the operation: numbers, sizes and operational availabilities of trucks, shovels and dumping point, distribution of the production over shovels, trucks' loading, travel (loaded and empty) and dumping times as well as their variabilities, shift's composition. The procedure models: the average duration of a complete truck cycle during stationary and non-stationary periods during the shift as a function of the number of trucks in the circuit, the composition of the average 100% operated shift, the simultaneous probabilities of operationally available shovels and trucks and the distribution of shovels and trucks according to production and cycle times. The procedure can be programmed for a small computer and requires only short computing time, which makes extensive studies of various parameter combinations practical to carry out. The development of the method is an extension of previous work by Morgan and Peterson {1}, who by simulation established the relation between the match factor (which is the ratio between the sum of one loading time pr truck in the circuit and the complete net cycle time) and the shovel's efficiency, and by Hayes, Splaine and Whitaker {2}, who established this relation from a large number of observations in the Nchanga pit in Zambia. The present method establishes this relation by a straightforward calculation procedure. Theoretical solutions to some situations are found in the litterature on the queuing theory. The papers {3},{4} and {5} give solutions to situations, which fall outside those encountered in the shovel-trucks circuit. These solutions together with simulations of in-termediary situations have been used to establish an interpolation procedure for the correction factors to be applied to the waiting time formula in order to cover the situations encountered in practice.

Jan 1, 1977

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By M. A. Reyes, L. Yan

"Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 hours while maintaining an apparent temperature (AT) below 95°F (35°C). NIOSH tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in NIOSH underground coal mine facilities to investigate the thermal environment over a 96-hour period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners increased over the 96-hour test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating heat and humidity temperature profiles for RAs not tested in situ. INTRODUCTION RAs are designed to provide a life-sustaining environment for miners who cannot escape after a mine disaster. One of the major considerations for integrating RAs in mine environments is the thermal environment inside the RA and the impact that the surrounding mine conditions have on the temperature and humidity buildup. Previous research has observed that the metabolic heat of the occupants and the heat released by the CO2 scrubbing systems will cause the RA interior air temperature to increase. In addition to the increase in temperature, an occupant’s respiration and perspiration, as well as the chemical reaction of the scrubbing chemicals with CO2, will contribute to an increase in humidity within the RA. The resulting internal thermal conditions, if not controlled, can subject miners to conditions that can lead to heat exhaustion, heat stroke, or even death depending on the duration and magnitude of exposure. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Mine Safety and Health Administration (MSHA) regulations require that RAs must be designed to ensure that the internal AT does not exceed 95°F (35°C) when the RA is fully occupied."

Jan 1, 2018

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By Joe Hachey, Jerry Dorn, Jeff Schutt, Derek Penrice

"Sound Transit’s East Link Project, a $3.7 billion (2015 $), 14-mile light rail extension, will connect downtown Seattle with the rapidly developing east side cities of Bellevue and Redmond. Among the most technically challenging aspects of the Project is the 2,435 foot long Downtown Bellevue Tunnel (DBT), which will be constructed through the central core of Bellevue underneath 110th Avenue NE using a combination of Sequential Excavation Methods (SEM) and cut and cover tunneling. The 1,980 foot long central SEM component of the DBT will be mined at shallow depth through challenging and complex geology, comprised of glacially overconsolidated soils, containing both regional and perched groundwater conditions and in close proximity to existing high rise buildings. The paper shares lessons learned from the planning decisions and risk based approach to the investigation, design and procurement processes which shaped the DBT configuration and enabled a successful transition to the project’s construction stage. INTRODUCTION The East Link Project is a voter-approved $3.7 billion (2015 $), 14-mile extension of the existing Sound Transit (ST) light rail transit (LRT) system from downtown Seattle, across Lake Washington via I-90, to the cities of Bellevue and Redmond on the east side of Lake Washington. With targeted completion in 2023, East Link will provide riders with an efficient and reliable connection between the largest population and employment centers on the east side and downtown Seattle. The project alignment is indicated in Figure 1 below.ST completed the Preliminary Engineering (PE) phase of the East Link project in late 2011. Subsequently the final design contract for the easternmost seven miles of the project was awarded to the H-J-H Team, a joint venture comprised of HNTB, Jacobs Engineering and Hatch Mott MacDonald in February 2012. H-J-H’s final design scope includes approximately 7 miles of double-track LRT between the east end of the I-90 East Channel Bridge and the Overlake Transit Center Station. While the project scope is extensive and diverse, the focus of this paper is the DBT. The DBT is located immediately north of the East Main Station, and travels approximately one half mile through downtown Bellevue under 110th Avenue NE between Main Street and NE 6th Street; terminating at the Downtown Bellevue Transit Center (BTC) Station. The location and extent of the DBT is indicated in Figure 2."

Jan 1, 2016

By M. Bunch

"THE SUPER CYCLE IS GONE The utopia of the rising sales volume, for mining companies from 2002-2011, was entirely due to rising production volume and prices. The Australian mining sector experienced an 18 percent annual growth rate in revenues, and 11 percent growth in prices. (1) However, EBIT remained flat during the same time period. In addition, Australian mines saw a 7 percent annual decline in both labor and capital productivity. (2) Mines in the U.S. and Canada produced similar results, whereas the world-wide mining industry has seen a productivity drop of 40% since 2001. (3) The decade “Bull Run” of rising prices was trashed by companies that chased low-quality assets while increasing debt on their balance sheet. It seemed everyone believed the “super cycle” would last forever, while completely ignoring the history of cycle downturns. Worldwide mining operations are as much as 28 percent less productive today than a decade ago, according to new McKinsey research. The results from McKinsey’s new MineLens Productivity Index (MPI), which adjusts for declining ore grades and mine cost inflation, show that the pronounced decline in productivity is evident across different commodities and is seen in most mining players and geographies. (4) McKinsey sees three important areas of focus to address the root causes of productivity decline. 1) Embed effective management operating systems at mines 2) Prioritized operational excellence and capabilities development 3) Focus on innovation Reality has now settled back in and companies are struggling to make ends meet. The basic management staple of controlling costs and improving the production/productivity that was lost in the excitement is now back in play. Traditional cost-cutting approaches, such as across-the-board spending cuts, layoffs, and hiring freezes are only short-term initiatives and will not permanently improve a company’s cost structure or improve long- term competitiveness. This can only be accomplished by engaging front-line employees and empowering them to make necessary improvements in their daily work. It is time for leaders to lead and develop cultures of continuous improvement within their organizations in order to sustain their mining project to the end of mine life. Successful operating managers require two different skill sets of Leadership and Management; knowing how to lead people in their organization and how to manage the work they do."

Jan 1, 2016

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800's; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900's by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder's in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

By Chee Theng

"So many talks, so little time.One of the toughest challenges associated with attending the SME Annual Conference and Expo is deciding how to allocate one’s resources. After accounting for keynote and plenary sessions, committee meetings, networking events, luncheons and exhibits, attending even one of the 109 technical sessions and more than 600 technical paper presentations can be a labor of love. Many, however, managed to make it to many of the sessions, including the mineral and metallurgical processing technical session on solvent extraction, ion exchange and electrowinning.At one point, that room was seated to near capacity, with a considerable number of the audience members standing by the walls at the back. Brittany Valera of Freeport-McMoRan Inc. was one who came early and enjoyed the session in its entirety. "Everything was pretty exciting," she said. "I really liked the modular plants. I think the future of mining, just like what we talked about in there, lies in thinking about things like remote locations, lifetimes of plants, anything that would be reusable and sustainable; and lower-cost and user-friendly would be really beneficial."Michael Moats, associate professor of metallurgical engineering at Missouri University of Science and Technology, started off the session by presenting on behalf of post-doctoral student Alex Luyima, who, like many before him, had been snapped up by industry and is now working for a secondary-metals refining company in Texas. Their team studied the nucleation and growth mechanism of copper on stainless steel from synthetic acidified copper sulfate in the absence and presence of chloride ions and three commercial organic additives: Hydrostar 4208, DXG-F7 and Cyquest N-900. Currenttime data were analyzed using known models, with reference to scanning electron microscope images. Good agreement was achieved between the models and SEM micrographs of deposits at a commercially relevant current density of 30 mA/ cm2. The addition of 20 mg/L chloride was found to increase the size and reduce the number of nuclei. The addition of 2.5 mg/L of each additive did not change the mechanism, but all three reduced the size and increased the number of nuclei, leading to more uniform coverage of the substrate with smoother deposits produced in twohour electrowinning experiments. N-900 had the best deposition coverage while DXG-7 was the easiest to dissolve."

Jan 1, 2014

By S. A. Hoenig

Introduction In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in Fig.1 . Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in Fig. 1. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 µm (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 pm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform. *The zeta potential is the voltage developed between the surface of a solid particle and the ion solution in which it is immersed. In the case of rock/ore materials in water, the zeta potential is negative.

Jan 1, 1984

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By J. E. Gebhardt, H. Toro, K. Y. Lee

Industrial-scale test results indicate superior metallurgical performance of column flotation compared to conventional cell flotation for copper cleaning. A technical comparison of bubble generation systems for column flotation is made. Two types of bubble generation systems are considered: the filter-cloth type spargers and the Turbo-Air® sparger, which utilizes an air-water mixture fed to the column through injection tubes. Examples of the improved technical performance available with an external sparger system are presented using data from plant tests conducted for specific applications with several different mineral ores. INTRODUCTION Column flotation is now a valuable unit operation which mineral processing engineers employ in the design and operation of flotation circuits in nearly all mineral applications. The acceptance of columns in the mid- 1980s by the minerals industry was paralleled by a rigorous approach to developing a scientific understanding of the design, scale- up, and operation of column flotation units (Finch and Dobby, 1990). Since then, column flotation has become a standard unit of the cleaning stage in many new mineral concentrator projects and has replaced older mechanical cells to improve process efficiency. The size of column cells has continued to grow from the initial 0.9- to 2.1 -meter diameter range, and it is not uncommon to find column cells today being 2.7- to 3.6-meters in diameter. With the success of the smaller units, the scale-up to larger cells has been proven and demonstrated by the performance of the large-diameter cells (Murdock and Wyslouzil. 1991). The use of columns in flotation circuits has also been accompanied by developments in modelling. control, and optimization of column performance (Lee et al, 1991). The bubble generation system is the heart of the operation of column flotation cells. The most common methods for generating bubbles can be divided into two types: the internal and external spargers. Internal spargers are typically a porous material, such as sintered glass, porous rubber or filter-cloth, or maybe a single- or multi-nozzle sparger. External spargers implies that a gas and a liquid (either water or slurry) are brought into contact outside the column and that mixture is then introduced into the column. Several types of external spargers are available today, and innovative designs for externally mounted air sparging systems have been a significant factor in the successful application of columns. Early types of bubble generation systems.

Jan 1, 1993