Search Documents

By Wayne A. Sadik

The mine ventilation system of the Henderson Mine provides a case study of designing and maintaining high-quality respirable air in a large underground mine with over 200 units of diesel-powered equipment. This system was designed with concern for minimizing exposure to personnel of siliceous dust, diesel exhaust, smoke, and potential fire hazards while optimizing general environmental air quality throughout the multilevel/multiheading operation. As a relatively new operation, the Henderson Mine incorporates a modern ventilating plant and mine de- sign as well as state-of-the-art technology where appropriate. Two main ventilation shafts approximately 2,300 ft (701 m) in depth (one intake, one exhaust) will handle 1.8 million cfm (850 m3/s) of air circulated throughout 60 miles (97 km) of drifting, providing the ventilation requirements for more than 25,000 diesel horsepower (18,642 kw) underground.

Jan 1, 1980

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By D. C. Durgin

Located near Ely, Nevada, the Robinson Mining District has produced gold since 1868 from the Ruth? porphyry copper system. Gold occurs in at least seven different deposit types, including porphyry copper ore, silica-pyrite replacements along favorable horizons, fault controlled silica bodies, intrusive breccias, stockworks in bornfels and in retrograde skarns. In all of these the primary controls localizing gold ore are structural .preparation and permeable hosts. Indicator elements associated with gold are Ag, As, Te, and to a lesser extent Sb and Tl. Pb, Zn and F are peripheral to gold or with it depending upon position within the system. The district has produced 87,000 kg (2.8 million ounces) of gold thus far. An additional 19,300 kg (620,000 ounces) of reserves are established, and well over 31,100 kg (1,000,000 ounces) of reserves are anticipated. I

Jan 1, 1989

By G. T. Adel

As a prerequisite to removing mineral matter from coal by any physical separation technique, the mineral and coal particles must be sufficiently liberated. In the case of the production of superclean (< 2% ash), low-sulfur products, the appropriate liberation size may be less than 10 µm. Unfortunately, much of the liberation data obtained at these fine sizes is only qualitative due to the lack of appropriate instrumentation. In the present work, computerized image analysis has been used to characterize several common eastern U.S. coals. In most cases, it has been found that micronizing of the coal is necessary in order to achieve sufficient liberation for deep cleaning. Liberation analyses of the products from the microbubble column flotation process have been used to distinguish problems in liberation from problems in selectivity, especially as they pertain to pyrite rejection.

Jan 1, 1989

By E. Gutierrez, P. Gillies

Asset Maintenance Readiness (AMR) provides a tailored reliability and maintenance strategy specific to operational needs. AMR delivers reliability and maintenance foundations for the plant and equipment before start-up. Having a dependable reliability and maintenance strategy before start-up is critical, particularly in those first weeks and months during ramp up to stable production. The Asset Maintenance Readiness is the integration of Reliability and Maintenance Engineering analysis/studies at the earliest stages of the new Production System concept and design and during the Capital Project CapEx phases; adding this analysis to the Capital Project CAPEX cost, will have an impact of 2% to 3% of total project cost, but will deliver a good compendium of benefits far from the AMR costs, and those results will be shown upon commissioning and during the life cycle of the plant.

Mar 2, 2022

By Noel A. Genco, Edward F. McCarthy, Robert J. Piniazkiewicz

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H,O. However, as a commercial commodity less than half of all talc sold has a purity exceeding 95%. Nevertheless, impure talc products find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are chlorite, dolomite, mica, magnesite, and tremolite. Steatite was originally a mineralogical term applied to pure talc. Today steatite usually denotes a high-talc ceramic body used as an electrical insulator, and the talc used in such applications is known as steatitic talc. Steatitic talc generally is found in massive, high- purity form and in the past was machined directly into electrical parts, which rarely is done today. Impure varieties of massive or block talc are still commonly termed soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soap- stone and talc this is natural, since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as slip) have been grouped together and called soapstone or talc. Further, there are mineralogical relationships between pyrophyllite and montmorillonite and between talc and hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Native Americans on Santa Catalina Island, CA. In the mid- 1800s soapstone from deposits along the western foothills of the Sierra Nevada Mountains was used by white settlers as building and ornamental stone and for the linings and foundations of furnaces (Anon., 1956). Previous to 1916 the annual recorded production in California did not exceed 1.8 kt. From 1912 to 1918, however, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state&apos;s annual output of talc was in the range of 8.2 to 18.2 kt. There was another increase in the mid-1930s, when the use of talc in wall tile grew rapidly. In California the production of talc grew to 57.2 kt in 1943. The post-war building boom helped California&apos;s production to grow to 108.9 kt in 1951. Production stood at 149.8 kt in 1968, 13 1.6 kt in 1969, 167.9 kt in 1970, and 140.7 kt in 1972. In the mid-seventies and early eighties, however, California&apos;s talc production declined to approximately 20 kt in 1992 due to reserves exhaustion and the material&apos;s tremolite content, which raised significant product liability concerns at the time. Talc mining in New York State dates from about 1878, when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville. In 1893 this operation was sold to International Pulp Co., which changed its name to International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc., in 1974. A new talc operation, Gouverneur Talc Co., owned by R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 180 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to more than 725 tpd. Talc was discovered in the area of Johnson, VT, in 1902, marking the birth of the Vermont talc industry. American Minerals Co. initiated plant operations at Johnson in 1904. MagnesiaTalc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963, Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine had a long history as a producer of talc crayons. Eastern Magnesia Talc Co. was formed in 1924 by the merger of Eastern Talc Co. and Magnesia Talc Co. In 1956 Vermont Mineral Co., with a talc mine at Hammondsville, VT, was also acquired. A new plant was then built at Gassetts to produce roofing products. In order to produce high grade products for several markets, Eastern Magnesia Talc Co. began operating a modem froth flotation plant at West Windsor, VT, in 1964. The ore was provided by the Hammondsville mine. This operation, known as Windsor Minerals, Inc., continued from 1972 to 1989 as a subsidiary of Johnson and Johnson Co. In 1989 Cyprus Minerals Co. acquired Vermont Talc, Inc. and Windsor Minerals, Inc.. thus consolidating the talc mining and processing operations at Hamm, Windham, Johnson, Chester, Ludlow, West Windsor, Troy, and Reading, VT, under one ownership. As the result of Cyprus&apos; sale of its worldwide talc assets to the RTZ Group in 1992, its US talc operations are now part of Luzenac America, Inc.

Jan 1, 1994

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By F. Ferella

In this paper several leaching tests were per-formed to optimize the leaching section of a hydrometallurgical process for the recycling of alkaline and zinc-carbon batteries. Zinc and manganese oxides were dissolved by an acidic-reductive leaching using sulphuric acid and oxalic acid as reductant. Leaching tests were developed according to a full factorial design. The operational variables were pulp percentage, sulphuric acid concentration, temperature and oxalic acid concentration. Additional tests were performed to evaluate the precipitation rate of Mn and Zn oxalates. Finally a hydrometallurgical process were proposed for the recycling of alkaline and zinc-carbon batteries, in which Zn and MnO2 are recovered from purified solution by electrowinning: Zn is recovered as metallic compound, while Mn can be recovered as electrolytic manganese dioxide (EMD), but recovery of further manganese compounds is possible with simple process changes.

Jan 1, 2006

By Bruce H. Mason

Lightweight aggregates are classified as those minerals, natural rock materials, rock-like products, and byproducts of manufacturing processes that are used as bulk fillers in lightweight structural concrete, concrete building blocks, precast structural units, road surfacing materials, plaster aggregates, and insulating fill. Other uses include architectural wall covers, suspended ceilings, soil conditioners, and other agricultural uses (Mason, 1989). One unusual agricultural use recently reported was for bedding on a crocodile farm on the south coast of Natal. It seems that female crocodiles became upset because there was no vermiculite in which to lay their eggs due to the late arrival of a consignment of vermiculite. The vermiculite was being used as a substitute for river sand to nest crocodile eggs (Griffiths, 1989). The various lightweight aggregate materials may be classified into four groups as follows: 1. Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials, such as pumice, scoria, tuff, breccia, and volcanic cinders. 2. Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing shale, clay, or slate in rotary kilns or on traveling grate sintering machines. 3. Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. This group of lightweight materials, with the exception of slag, has become less significant and will not be discussed in this chapter. Other lightweight aggregates are beginning to appear in the marketplace. Some are the result of manufacturing processes on industrial byproducts and/or waste products, such as fly ash and incinerator residue (Bigner, 1992). 4. Manufactured Insulating Ultralightweight Aggregates-pre- pared by pyroprocessing ground vermiculite, perlite, and diatomite. The application of diatomite in brick and in extruded and aggregate forms has declined in recent years (Kadey, 1983) and will not be considered in this chapter. Lightweight aggregates for structural concrete and concrete masonry units, according to the American Society for Testing and Materials (1986) consist of "aggregates of low density used to produce lightweight concrete, including: pumice, scoria, volcanic cinders, tuff and diatomite; expanded shale, clay, slate, perlite, vermiculite or slag; and end products of coal or coal combustion" (Mason, 1989). Lightweight aggregates are distinguished from other mineral aggregate materials by their lighter unit weights-1 281 to 1 602 kg/m3 or less for loosely packed lightweight aggregates-as com- pared to 2 002 kg/m3 or more for crushed stone, sand, gravel, air-cooled slag, and other common mineral aggregates. The specific gravities of these lightweight aggregates are also used to classify them for use in concrete; they range from the extremely light materials, used for insulative and non-structural concrete to expanded shale, clay, slate, and slags used for structural concrete. Vermiculite and perlite are sometimes referred to as super light- weights. Insulating concrete (non-load bearing) weighing as little as 240 kg/m3 can be made with these aggregates. Natural aggregates such as pumice, pumicite, and scoria are normally made into concrete weighing about 400 to 480 kg/m3. Expanded shale, clay, and slate produced in a rotary kiln make structural concrete ranging from 1 201 to 1 842 kg/m3. Expanded shale and clay produced by sintering make concrete that ranges from 1 442 to 1 922 kg/m3. Air-cooled slag produces concrete ranging from 2 162 to 2 403 kg/m3. The low density lightweight aggregates are used primarily for insulating purposes. They have relatively low compressive strength. The middle density aggregates are used for insulation and for fill. Those at the upper end develop excellent compressive strength and are used in many structural applications (Anon., 1971). In recent years, the production of lightweight aggregates in the United States for all uses (including insulation and construction materials) has averaged about 19 Mtpy (Table 1). The production and consumption of lightweight aggregate is closely tied to the fortunes of the construction industry and the need to construct energy efficient buildings. Recent years have seen the production of lightweight aggregate approach the levels of the early 1970s. The period of 1979 to 1981 was a low point in production levels. The low levels of production were caused by significantly higher plant energy costs due to the large amounts of fuel and energy used in the production of most types of lightweight aggregate. Lower levels of construction activity also affect production levels. This chapter focuses on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and on both the production and use of manufactured structural light- weight aggregates. Some additional comments are made on byproduct materials. Separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders are elsewhere in the volume. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials.

Jan 1, 1994

By John C. Schneider

In the mid 60's Prochem & Hydrochem Development, it's research division, developed the high efficiency Maxflo impeller. Since the Maxflo impeller had a design that had proven to be very efficient in gas-liquid-solid contacting, it was a natural extension to apply this design to flotation & the research commenced in the mid 80's. An opportunity to test the energy savings occurred at Dickenson Mines in 1987, & comparative results with existing conventional flotation cells showed a marked increase in capacity, grade & recovery with 25% less power applied. This r success was followed by the installation of the fist agitated Flotation Colunm (5ft. dia. x 25ft. tall). As a result of the Dickenson success, Hydrochem started a comprehensive 2-part research program in 1988. At Randol Gold Forum 1988 a paper by Hydrochem was pre

Jan 1, 2000

By Michael Mccorkle

The Turnkey Project contracting approach is a very viable project delivery system for many mine and mill owners. Generally speaking, the Turnkey Project approach makes sense when the owner knows what it wants, is willing to accept the contractors judgement on process elements and maintenance standards, and early construction completion/facility stmt-up are of primmy importance. Projects with unclear process and project objectives make poor candidates for true Turnkey applications. If the objectives are unclear, under development or significant refinement, the owner's effort should go into a good schedule "A" package allowing Engineering, Procurement, and Construction (EPC) contractors to develop cost and schedule proposals for the final design ( engi­neering), procurement and construction of the facility. Figure 1 and 2 graphically depict (in general terms) the stan­dard Design-Bid-Build, Construction Management (CM) Fasttrack, EPC, and Turnkey Approach.

Jan 1, 1998

By Gary L. Simmons

Many large (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to conventional flotation concentration using air as the flotation gas medium. Over the past five years Santa Fe Pacific Gold Corporation (SFPG) has investigated flotation process options to economically treat refractory ores and resources of this type at its Lone Tree and Twin Creeks mines. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation ..:hemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2 TEC. This paper discusses the development of this technology and compares N TEC results with conventional flotation practice.

Jan 1, 1997

By T. Valentine

The SX-EW operation at Morenci includes three electrowinning tankhouses. Stainless cathode blanks require the use of insulating plastic edge strips, which typically have a service life of 1-2 years, therefore, regular replacement of edge strips is a fact of life in tankhouse operations. The largest tankhouse, Central, converted from starter sheets to stainless steel cathode blanks in 1999. During the first year of stainless blank operation at Central Tankhouse, the initial installation edge strips started failing at accelerated rates and there was a sudden need to replace edge strips and repair between 350 and 400 cathode blanks per day. This paper details the design and building of cathode repair shops at the Morenci tankhouses, including choice of equipment and layout design. The objective was to increase efficiency through the use of cathode handling equipment and flow of material.

Jan 1, 2002

By J. Ugarte-Núñez

Biodiversity assessments that are developed in different stages of a mining project, have different objectives that define the methodology to be used in each of these stages. In this way, we define two stages of a project: 1) the time at which assesses the state of biodiversity or biological components, before any intervention in the project area, previously defining the area of direct influence and indirect influence of the project for each biological group to be evaluated and 2) the time when certain groups or biological, are monitored during the developmental stages of the project with you to obtain information about the level impact they may have, for project activities. It discusses the methodological differences that must be used in both biodiversity assessments: to develop biological baselines and in those assessments aimed at monitoring different components of biodiversity.

Jan 1, 2011

By Shunji Sukizaki

Recently development of cheaper and cleaner energy sources has become a more important and urgent issue, because of the soaring crude oil price and environmental problems such as global warming. In this social context, to establish basic technologies and solve fundamental issues associated with environmental impact assessments, the Environmental Impact Assessment Group of the Research Consortium for Methane Hydrate Resources (MH21 research consortium) in Japan has conducted a number of research and development activities since FY2001. These activities include: 1) surveys of the marine environment that will form the basis of environmental impact assessments associated with methane hydrate development; 2) the development of core technologies to monitor deep-sea environments; 3) research of major issues related to environmental impact assessments; and 4) the development of numerical models to predict the deformation of seafloor sediments containing methane hydrates.

Jan 1, 2008

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002