Search Documents

By Tim Q. Haldane

The ability to efficiently process low grade gold ores has allowed the Gold Fields Mesquite Mine in Imperial County, California to expand from a 2.1 million tonne per year rate in 1986 to its present 7.3 million tonne per year processing rate. Increased tonnage demands led to the 1989 construction and start-up of a dump leach pad to supplement the existing heap leach operation, resulting in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. An overview of current operating practices at Mesquite is presented along with metallurgical and economic comparisons between the crushed and run-of-mine ore heaps.

Jan 1, 1990

By J. H. Tylczak, R. Blickensderfer, D. J. Singleton

As part of its research on wear of mining and mineral processing equipment, the US Bureau of Mines evaluated the erosion-corrosion characteristics of 12 alloys in phosphoric acid waste water. Tests were conducted on 2- and 5-cm-diam specimen8 in 12- and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with an initial pH of 1.6. For comparison, grinding tests also were conducted in tap water. Static corrosion tests in gypsum pond water also were carried out. For all alloys tested, the wear by erosion-corrosion was greater than the sum of erosion plus static corrosion. A low-alloy, high-carbon steel and a high-manganese, nitrided stainless steel were the most cost-effective materials

Jan 1, 1987

By S. C. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photoelastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface, and (3) the effects of subsidence on tension in the truss members.

Jan 1, 1987

By R. Houot, C. Leschevin, G. Gillet

In mineral processing, conventional magnetic separators are equipped with traditional magnetic circuits (magnetic iron yoke with copper coils or iron-clad solenoid) that develop magnetic fields of less than 2 T'. For minerals of low magnetic susceptibility, use of these circuits has many disadvantages. Only a separator with a superconducting magnet can contribute to solving the problems and produce a high magnetic field. This paper presents and describes a magnetic separator having a superconducting magnet with integrated closed circuit for helium liquefaction. The system generator and maintenance are simplified by extensive automation realized by a versatile program- mable autocontrol unit. A comparative study if the results on concentration and purification of different raw materials with the new and with conventional separators is described.

Jan 1, 1987

By Jerry C. Tien

In 2009 China mined 2.695 billion metric tones (Gt) of raw coal. It is estimated that only 3-5% or roughly 135 million metric tones (Mt) of these were mined from 300 some surface operations. Except for a dozen or so large modern operations, most of China's surface coal operations are small by western standards, with annual production ranging from a few thousand tones to 300,000 metric tones (mt). Depending on the size of operations, equipment used range from small trucks and shovels to large bucket wheel excavators and draglines in sizable pits. This article provides a brief overview of China's surface mineable coal reserves, mining methods commonly used and increasing environmental concerns; introductions of several large surface operations are also provided.

Jan 1, 2012

By V. V. Ershov

Application of computers in the study of mineral deposits pursues two main objectives: 1. obtaining reliable information on the properties of the orebody; 2. providing graphic presentation of this information for its optimal use. These problems are successfully solved if, during preparation of graphic computer software, we apply modern mathematical methods. The present paper treats the problems of using geostatistics for graphic modelling of deposits by means of graphic computers. It should be noted that in this field geostatistical methods may be used for: a) indices evaluation in the nodes of regular grid, or in given blocks, by means of kriging, for its designated purpose; b) for evaluation of accuracy of interpolation methods, traditionally used in computer graphics, and not being optimal.

Jan 1, 1986

By J. A. Muñoz, A. Ballester, C. Gómez, M. E. Sevillano, M. Figueroa

The electrochemical behavior of massive chalcopyrite (CuFeS2) electrodes has been studied in the absence and-in the presence of mesophilic microorganisms, using cyclic voltametry as analytical technique. The culture was principally formed for Thiobacillus ferrooxidans, Thiobacillus thiooxidans and Leptospirillum ferrooxidans. The results showed that the reactivity of the chalcopyrite gradually increased with the bacterial treatment. The anodic dissolution process of the chalcopyrite treated with microorganisms was related to the breaking of passive layers when the applied potential increased. The analysis of the surface products showed that the chalcopyrite was covered with a superficial film avoided its dissolution during the bioleaching test. So, the rest potential of the bioleached samples increased possibly as consequence of its superficial transformation.

Jan 1, 1995

By Richard L. Ranich, Frank F. Aplan, J. B. Hiskey, Robert S. Thompson, B. J. Scheiner

Acidic waters typified by acid mine drainage, copper dump leach solutions and steel pickle liquors will typically contain SO4-2 and cations such as Fe+3, AI+3 and for the pickle liquors, sometimes Cr+3. These acidic waters will often react with limestone, present naturally or introduced for purposes of solution neutralization, to form reaction - inhibiting coatings of gypsum and gelatinous, metal hydroxide precipi¬tates. The coating thickness, as a function of pH, was quantified for both reactive (calcite, limestone) and non-reactive (quartz, barite, fluorite) minerals, and the data were related to the hydroxy species diagrams and to solution turbidity measurements. Coatings were found on the reactive minerals at a lower bulk solution pH than on the non-reactive minerals.

Jan 1, 1993

By J. K. Mokka, P. D. Rao, H. K. Lin

Extensive exploration has resulted in delineation of a massive sulfide district on the north flank of the east-central Alaska range. The district covers approximately 400 mi2 and contains numerous stratiform, transposed and some replacement type sulfide deposits ranging in size from less than 1 million st to 20 million st. Five types of ores were sampled for the study. Mineralogical analysis revealed that the minerals are too fine grained for conventional grinding and beneficiation. Hydrometallurgical studies were conducted using ferric chloride as a lixiviant. Ore microscopic studies as well as electron microprobe analyses of minerals in the raw samples and leach residues explained the low recoveries for certain elements as well as sources of impurities that need to be eliminated from the process streams.

Jan 1, 1992

By M. A. Mahtab, N. M. Cruickshank, M. T. Wane

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment, and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) microseismic activity. Geophysical and engineering methods for detecting these characteristics are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1987

By Yoshihiro Kawarabata

INTRODUCTION The shield-driven method in Japan has been adopted widely in soft ground tunneling, namely, subway, water supply, sewer and utility tunnels, and recently this is an indispensable method in urban area. Since this method was started to adopt on a full scale from the beginning of 1960, construction achievements in length were about 830 km for 15 years until 1974 (1). According to the recent informations of the Japan Tunneling Association, the achievement in length under construction as of December, 1977, was about 350 km (2) and the extention of increase in shield-driven method can be guessed (Tab. 1). Tab. 1 - Achievement in Length by Shield-driven Method (As of December, 1977, Unit: m) (---): Achievement by Okumura Corporation [ ]

Jan 1, 1979

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By Rick Sarkisian, Greg Girardey, David Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 "Welded Steel Conveyor Pulleys" adequately defines pulley assembly standards for light material handling applications. However, most mining applications demand pulleys of higher reliability and load capacity than that offered by CEMA standard pulleys. Various sources have published specifications for "Engineered" conveyor pulleys. Typically, these specifications require T-section type pulleys applicable to operating belt tensions exceeding 439 N/mm (2,500 lb./in.). This paper examines the application of CEMA standard pulleys, T-section pulleys and also a mining duty pulley design. The mining duty pulley fills the void between CEMA standard pulleys and T-section pulleys and can eliminate the high cost and long lead times associated with T-section type pulleys.

Jan 1, 1998

By E. Yuksel

Noted as one of the 20 major economies of the world, Turkey is a semi-arid plateau between the Eurasian and the African continents. With its surface area of 780 thousand sq km, it supports a population of 70 million people. While the mining history of Turkey can be traced back as far as 7 000 B.C., mining currently generates only 2% of Turkey’s gross national product. Turkey has 77 of the 90 principal minerals that are mined world-wide. Currently, some 5 000 mine occurrences including copper, lead, zinc, iron, gold-silver, chromite, sepiolite, mercury, and coal deposits, soda ash, marble, zeolite, feldspar, magnesite deposits, as well as the world’s largest known borate deposits, have been discovered and partially explored.

Jan 1, 2004

By J. L. Gent

Compressed air distribution networks are essential for powering equipment in many mines even though some mines are replacing them with electrical power for hydraulic drills. Compressed air can be costly especially if the system is poorly designed and maintained. This paper outlines a technique for proper compressed air system design that will help mine managers reduce compressed air power costs; an important topic in today's highly competitive international minerals market. Compressed air system design is complex. It requires specifying: 1) air quantity and pressure in all branches of a large network, 2) proper location and types of valves and fittings, 3) the network solution that determines compressor requirements, 4) optimal hose and pipe, diameters, 5) receiver and compressor accessories, and 6) required capital and operating costs.

Jan 1, 1989

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão Mine in Brazil. They are predominantly blue apatite, followed by green apatite and, less frequently, yellow apatite. The chemical compositions of these types of apatite were determined by electron microprobe analysis and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Blue and green apatite responded well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite has the lowest phosphorus pentoxide (P2O5 ) content and largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest phosphorus (P) and calcium (Ca) grades and lowest substitution level.

By David Shuck

On November 1991, Homestake Mining Co. completed the installation of a $5.7-million, 2.7-kt/d (3000-stpd) flotation circuit into the flowsheet of the McLaughlin Mine in California's coastal mountain range, about 113 km (70 miles) north of San Francisco. This addition reduced overall operating costs and improved the gold recovery of the low-grade refractory reserves over that expected from direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate that is used to supplement feed to the pressure oxidation circuit. The McLaughlin operation started in 1985 as the first pressure oxidation plant for treating sulfide refractory ore. During the mine's short history, efforts have been made to reduce costs and increase production through process development.

Jan 1, 1994

By B. E. Dindsale, P. B. Altringer, R. H. Lien

The Bureau cf Mines, U.S. Department of the Intericr, is investigating biolcgical and chemical deccntaminaticn of cyanide- containing leachates and residues. Biolcgical cyanide cxidaticn, using bacteria isolated from a precious metals tailings pond, destroyed >85 pct of the cyanide in several prccessing solutions containing up tc 280 ppm CN. Reaction time varied from about 4.5 hr in a trickling reactor using quartz as a bacterial substrate to 2 mo in unagitated, covered flasks. Chemical techniques were used to destroy the remaining complexed cyanide down to 1 ppm. Exploratory tests were also conducted using spent ore from heap leach operations as the bacterial substrate to determine if biological cyanide oxidation could be used to destroy the residual cyanide in spent heaps.

Jan 1, 1991

By A. Yehia, J. S. Hu, J. D. Miller, M. Misra

Fluoride activation has been evaluated by Hallimond tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Experimental results of fluoride adsorption by collophanite suggest that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites. At high fluoride concentration, calcium fluoride appears to form at the collophanite surface involving a surface precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which suggest a metathetic exchange with phosphate from the collophanite lattice during the surface precipitation process.

Jan 1, 1988

By D. U. Gustafsson

After half a million meters drilled with Wassara we are now confident that ITH hammers powered with simple water will become an established product for production drilling. Today four drill rigs in LKAB Malmberget equipped with Wassara drill about 25 000 m per month of 4 1/2" holes. In Kidd Creek, Canada, Was sara is used for production drilling in stopes with good results. The first Wassara 6" hammer has drilled a 36 meter long, completely straight horizontal cut hole for drifting in the LKAB Malmberget Mine. Main advantages are about doubled penetration rate, very good air quality and improved hole cleaning which facilitates stabilized drilling. Disadvantages are resistance to new technology and, in some cases, the increased use of water.

Jan 1, 1995