Search Documents

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By C. R. Copeland

Combustion processes, comminution and materials handling can generate airborne particulates. Regulation of these particulates by the U.S. Environmental Protection Agency (U.S. EPA) is becoming progressively more stringent, and regulations will soon include ?nanoparticulates,? which are particles finer than 100 nanometers (0.1 mm). Nanoparticulates are believed to have significant negative health effects due to their high surface area and reactivity. Although it was argued that nanoparticulate concerns were only important for combustion, studies at Michigan Technological University have shown that materials handling and comminution release significant quantities of nanoparticles into the air. Laboratory studies have shown that the use of sodium metasilicate reduced airborne particles finer than 10 mm (PM10) by 86% and particles finer than 2.5 mm (PM2.5) by 80% for iron ore. Additional studies were conducted that revealed that nanoparticulate emissions were present in the types of operations conducted at pyrometallurgical facilities.

Jan 1, 2008

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000

By Thomas G. Goonan

Copper production through smelting generates large volumes of material flows. As copper contained in ore becomes copper contained in concentrate to be fed into the smelting process, it leaves behind an altered landscape, sometimes mine waste, and always mill tailings. Copper concentrate, fluxing materials, fuels, oxygen, recyclables, scrap and water are in-puts to the process. Dust (recycled),gases — containing carbon dioxide(CO2) (dissipated) and sulfur dioxide (SO2) (mostly collected, transformed and sold) and slag (discarded or sold) — are among the significant process outputs. This article reports estimates of the flows of these input/output materials for a particular set of smelters studied in some countries. They include Chile (Altonorte, Caletones, Chagres, Chuquicamata, LasVentanas and Potrerillos), Japan(Naoshima, Onahama, Saganoseki,Tamano and Toyo), the United States(Garfield — Fig. 1 — Miami and Hayden) and Europe (Glogow I, Glogow II, Huelva, Norddeutscheand Ronnskar).

Jan 1, 2005

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty's and early seventy's, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70's to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By D. J. Rose

The San Miguel Mine is owned by San Miguel Electrical Cooperative, Inc. and operated by Atascosa Mining Company, a wholly-owned subsidiary of Morrison-Knudsen Company, Inc. This multiseam, single-zone lignite surface mine is located near Jourdanton, Texas, 110 kilometers (68 miles) south of San Antonio. Lignite extracted from four closely-spaced seams is used to fuel the 400-MW San Miguel Power Plant. Recovery depths range from 7 to 37 meters (25 to 120 feet). The mine began stripping operations in the spring of 1980 and now produces approximately 2.5 million tonnes (2.8 million tons) of lignite annually. Atascosa Mining Company is responsible for production, maintenance, engineering, and management services. Production responsibilities include topsoil removal, overburden removal, lignite mining, spoil pile regrading and topsoil replacement, as well as ash disposal and construction and maintenance of water retention and diversion facilities.

Jan 1, 1984

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By Donald L. Gaughenbaugh

Under the terms of the 1970 amendments to the Clean Air Act, the EPA established national ambient air quality standards for a number of pollutants. Sulfur dioxide (SO2) was one of these pollutants. These ambient air quality standards have had perhaps their biggest impact on the power utilities. In an effort to meet the air quality standards set forth by the EPA, utilities using high sulfur fuels have been forced to install flue gas desulfurization (FGD) systems. The majority of FGD systems in operation today are nonregenerable systems, that is the by-product of the system is disposed of, usually into settling ponds. Limestone slurry is the most common reagent used to remove SO from the flue gases. The calcium carbonate (limestone) slurry interacts with the flue gas, absorbing the SO2 and forming a by-product of calcium sulfate/sulfite which is disposed of.

Jan 1, 1986

By M. A. Alan

The Bellavista Gold Deposit lies 75 Kms north west of San Jose, the capital of Costa Rica, Central America and 3 Kms north east of Miramar, in the Province of Puntarenas. The total road distance from San Jose to the deposit is 120 Kms all paved road except for a 2.5 Km graded, gravel road on the property (Figure 1). Infrastructure services in the Miramar-Puntarenas area are well developed with electrical power distribution, a modern port facility and community services being available. The deposit lies on the south west flank of the Tilaran Mountain Range between an elevation of 550 and 800 meters above sea level. The local topography is steep, originally covered with pre-montaine, tropical wet forest vegetation which has been largely destroyed due to clearing for cattle grazing. The annual rainfall is approximately 2,950 mms, 90% of which occurs between May and October.

Jan 1, 1992

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

Zirconium chloride is of great commercial importance as starting materials for production of ZrO2, Zirconium metal and other Zirconium compounds from its main resources (Zircon Sands). The present study concerns with preparation of pure ZrO2 from Zircon by direct chlorination technique. Different parameters affecting the chlorination process are studied viz. carbon, chlorine flow rate temperature and time. The chlorination extent is determined from the loss in weight and chemical analysis of reaction products. The maximum chlorination extent -92% are achieved at 1100°C for 30 min. Zirconium oxide is produced from the collected zirconium tetrachloride either by calcination at 900°C or by hydrolysis in water in presence of RCI with a purity = 99%. Evaluations of the products of the process are investigated microscopically and by X-ray diffraction. The apparent activation energy of the chlorination of Zircon is determined to equal 36 kJ/mole.

Jan 1, 1997

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974