Search Documents

By R. V. Ramani, A. S. C. Owili-eger

Mathematical modeling is a scientific exercise with the objective of developing simplified mathematical statements that relate to one another the same way as the processes that are being modeled. The utility value of the model is dependent on the ability of the model to closely approximate prototype behavior. Development of a perfect model, therefore, is an unrealistic objective because of the simpli¬fying assumptions made in building it. However, for a model to be acceptable for application, its operating characteristics or data generated from it should, within reasonable accuracy, duplicate proto¬performance. The validity and accuracy of a model depends on the mathematical constraints presupposed in model formulation. The final model must be tested for mathematical validity and for closeness of representation of the prototype. Mathematical validity, does not, however, imply that the model is accurate and correct but is prerequisite. Model testing and verification for the steady state model are given in Owili-Eger et al (1973). The unsteady state model has been tested for mathematical validity and found to be correct but has not yet been applied to a field condition for lack of data. However, in the application discussed below, the unsteady state model results are compared with pressure curves reported in literature and also with results from the steady state model. Coal seam characteristics and gas reservoir pressure used in this application are extracted from Kissell (1972). These characteristics are for the Pittsburgh seam, Federal No. 2 Mine, Fairview, West Virginia.

Jan 1, 1974

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949

By Charles S. Allbright

To develop a method for predicting the stability of a fuel during long-term storage from rapid aging tests at 200° F, the Bureau of Mines determined the stabilities of three gasoline base stocks and an alkylate blending stock in both sealed storage and aerated storage at 110° F for periods extending to 32 weeks. Stabilities of samples containing gasoline-additive compounds were compared by aging, using two methods--rapid aging in a bomb at 200° F for intervals up to 16 hours and storage at 110° F. The additives used were an uninhibited tetraethyllead motor mix, N,N'-di-sec-buty1-p-phenylenediamine and 2,6-di-tert-butyl-4-methylpheno1. Results were related by graphs that enable predictions of gum and sediment formation during storage from data obtained in bomb tests. A premium-gasoline base stock and the alkylate proved to be stable, but the two regular-grade gasoline base stocks were found to be unstable. Addition of the diamine antioxidant improved the stability of both of the regular gasoline base stocks, while the phenol antioxidant improved only one of them. The presence of the tetraethyllead decreased the storage stability of all four fuels, both with respect to formation of gum and precipitation of inorganic sediment. The rapid test at 200° F appears to offer promise as a basis for a method of predicting gasoline stability in long-term 110° F storage.

Jan 1, 1968

By Ronald D. Hill, Elmore C. Grim

Sediment is one of America's greatest pollutants. More than a billion tons of sediment reach the major streams of the United States annually(l). Damages are reflected in the reduced carrying capacity of streams, clogged reservoirs, destroyed habitat for fish and other aquatic life, filled navigation channels, increased flood crests, degraded facilities for water-based recreation, increased industrial and domestic water treatment costs, premature aging of lakes by enrichment of the water with silt-carried fertilizer that promotes algae growth, destroy crops, and reduce productivity of flood plain soils. Erosion and sedimentation are natural processes that are usually gentle actions releasing controlled amounts of silt from watersheds to receiving streams. Surface mining activities accelerate these natural processes and short duration, high intensity storms can become a violent force moving thousands of tons of soil in a brief period of time. Cover is a very important factor. With the removal of ground cover, water moves across the denuded area on its own terms picking up soil particles as it flows and leaving gullies behind. The susceptibility of strip-mined land to erosion depends on: 1.Physical characteristics of the overburden 2. Degree of slope 3. Length of slope 4. Climate 5. Amount and rate of rainfall 6. Type and percent of vegetative ground cover. By development of erosion and sedimentation control plans before disturbance of the area, many of the detrimental effects of strip mining can be prevented.

Jan 1, 1974

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

The U.S. economy showed further strength during the third quarter of 1983, continuing the upward trend discussed in the last two issues of Minerals and Materials. The National Association of Purchasing Management composite index increased to a 10-year high of 67. 1 in July. (A value of 50 or greater indicates expanding industrial activity.) The index, a weighted composite of new orders, production, employment, vendor performance, and inventories, is derived from a survey of purchasing agents for about 250 industrial firms. Investment and Other National Economic Indicators The strong consumer surge of second quarter 1983 was reinforced during the third quarter by the performance of private investment. Because of this, many analysts became more optimistic about the strength of the recovery and its potential for being sustained. Capital investment growth, negative since 1980, was positive for every investment component in the third quarter of 1983. Preliminary estimates indicate a real increase of $1.4 billion (at an annual rate) in private investment expenditures on nonresidential structures, an increase of $4.3 billion (at an annual rate) for producers' durable equipment, and an increase of $4.8 billion (at an annual rate) in real inventory levels. The second quarter 1983 increase in expenditures on producers' durable equipment was the first indicator that investment recovery would occur during the rest of the year (table 1). Corporate profits in total manufacturing increased $6.5 billion from first quarter to second quarter 1983 (table 2).

Jan 1, 1983

By Irving Hartmann

As part of the continuing effort by the Bureau of Mines to promote mine safety, research work is being conducted at the Experimental coal mine, Bruceton, Pa., on the prevention of coal-mine explosions and on other mine-safety problems. The principal subjects studied during the past 2 years are briefly described in this paper. Although at present these problems are relevant particularly to the mine layout and to high-speed mining practices in numerous American coal mines, it is hoped that the findings will prove interesting and useful also to our European research colleagues. Some of the investigations treated here will be presented in greater detail in forthcoming Bureau of Mines reports. 1. UNDERGROUND STORAGE OF COAL CUTTINGS The seams in mist American bituminous-coal mines are undercut, shear-cut, or top-cut before blasting. The cuttings arc generally loaded out with the balance of the coal. However, in some mines it is not economical to load and remove cuttings from the mine. This applies especially if the cut section of the seam is of appreciably lower grade than the rest of the coal, or if the cut is made partly into an adjacent stratum that is high in incombustible content. In such mines the cuttings are sometimes stored in random heaps in rooms or other areas, along the ribs of mine entries, or in layers on the floor of rooms or entries.

Jan 1, 1956

By Kevin Connor

The mineral industry continued to be an almost negligible contributor to the country's economy as the Government continued its 1979 ban on any mineral exploitation for export; a policy initiated at the end of 1979. A national program had been underway since that time to map and inventory all mineral resources so as to permit future exploitation of mineral wealth in the beat interests of the country and its inhabitants. In March 1982, the British Sulphur Corp. Ltd., under contract to the Burundi Government and the International Bank for Reconstruction and Development (World Bank), began a feasibility study of Burundi's phosphate deposits at Matongo-Bandaga for potential commercial exploitation. The 1-year project effort was to define ore reserves, conceptually design mining operations and processing facilities, estimate capital and production cost, and develop a regional market and distribution survey. Work completed during the year comprised geological exploration and reconnaissance and 1,200 meters of core drilling. Reserves in excess of 5 million tons of ore-grade phosphate were estimated available for mining. Rare earth mineralization was associated with the primary apatite. The associated carbonatite within the rock matrix was preliminarily assessed to be of value as a raw material for the manufacture of cement. The contract effort was valued at $1.2 million? Matongo-Bandaga is located approximately 40 kilometers north of the capital city of Bujumbura and alongside one of the country's few paved roads.

Jan 1, 1984

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user's physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

The last issue included a discussion of recent indications of a 1983 recovery and a brief analysis of the contribution of the U.S. mining industry to the gross national product (GNP). In this issue we present sales and other data indicating the strength of the 1983 recovery and quantitatively analyze the structural shifts that have taken place in the U.S. economy and mining industry since 1972, and changes in electricity consumption by the mining industry. U.S. Economic Recovery The tentativeness in the February/March issue of Minerals and Materials regarding the strength and sustainability of the U.S. economic recovery can now be replaced with a note of increased confidence. Real growth of GNP on an annual basis in the first quarter of 1983 was 2.5 percent, compared with 1.4 percent predicted in the Economic Report of the President.1/ Preliminary second-quarter 1983 data provide further cause for optimism. Recently released data indicate that consumer spending is playing a key role in the recovery. Retail sales have increased significantly across a wide array of goods, especially consumer durables, where sales increased 4 percent from March to April (table J) and were 12 percent higher in April [ ] than the 1982 monthly average. Consumer durable sales were led by sales of building materials spurred by the growth in residential construction, motor vehicles and parts, and household durables, including appliances and furniture.

Jan 1, 1983

By E. D. Eastman

"The factors that determine the efficiency of reduction of iron oxides by gaseous reducing agents may be considered in two classes; those which effect the equilibrium between the reacting substances end their products, and those which affect the rete of reaction. Both sets are of prectical importance, the former as influencing the maximum possible efficiency and the latter as determining what fraction of the maximum yield may be readily or profitably obtained. In addition, the thermal changes attending the reduction greatly affect the chance of successful industrial application of any such process, and knowledge of them is necessary for the intelligent design of apparatus and control of the reaction. Some aspects of each of these three divisions of the problem are discussed below.I. The Maximum Reducing Power of Fuel Gases on the Oxides of IronsThe gases that heve been considered specifically in this work are coal gas, water gas and producer gas, typical analyses” of which are given in Table 1 Of the various hydrocarbons represented in Table 1, (several being grouped or averaged as C2R4), methane is the only gas assumed to be capable of existence at appreciable pressures under the conditions of interest here. The equilibria in the several systems which may ensue when one of the above gases is allowed to react with the iron oxides, may therefore be represented in the most general case by equations of the type of the following arbitrarily chosen ones:"

Jun 1, 1923

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By Thomas J. Peters

This report is part of the U.S. Bureau of Mines Idaho Land Assesment Program to study the mineral resources of priority roadless areas in Idaho. The results of these mineral inventories provide minerals information needed to make wise decisions regarding future land management practices, and to ensure a dependable supply of minerals at a reasonable cost. The 16,300-acre Lionhead area, studied in 1991, lies along the Montana border north of Henrys lake, 10 mi west of West Yellowstone, Montana. The study area includes much of the rugged Henrys Lake Mountains, and is largely covered with conifer forest. Several peaks are over 10,000 ft in elevation. The Lionhead area has been proposed for Wilderness. No mineral resources were identified within or near the Lionhead study area. Five prospects occur in, or within 1 mi of the area: these include 1) an intermittently used road gravel pit, 2) the Thimbleberry lateritic iron prospect, of geologic and historic interest only, 3) the Tick Heaven talc prospect, 4) the Dry Fork garnet prospect, and 5) the lynx prospect, which appears to be of historic interest only. Talc is seen only as float at the Tick Heaven prospect, but the geology is permissive of talc resources at depth. The garnet prospect, and nearby similar alluvial terrane, mainly outside the study area, appears to be the most likely setting to contain mineable resources. Examined workings include four trenches and pits in rock and one gravel pit.

Jan 1, 1992

By John B. Gayle

The probable inadequacy of physical tests of coke for the purposes for which they are made has been a subject for discussion for many years. However, little has been published in this connection, even though most workers in the field believe that the physical properties of coke are of major importance in its utilization in the steel and allied industries. In fact, the reproducibility of the recognized tests is largely unknown or can only be approximated. This situation occasions many difficulties when attempts are made to judge the coke-production qualities of various coals or coal blends. During World War II the Coke Production Committee, composed of representatives from industry and the Solid Fuels Administration, concluded that study of existing testing methods and possible improvements would be of material assistance in answering questions relating to coke quality. Since that time the Bureau of Mines has taken samples of coke produced in industrial slot-type coke ovens in connection with studies aimed at extending coking-coal reserves by adding to the list of sources known to be suitable for this purpose. Testing procedures on these cokes were arranged so that the data obtained would yield information on (1) the degree of precision of tests commonly used in the industry, (2) the causes of the known poor reproducibility in several of the physical tests, and (3) possible improvements or modifications of existing physical testing procedures.

Jan 1, 1953

By D. Litton, H. Dobroski, J. G. Kovac

Since 1910, the U.S. Bureau of Mines (USBM) has investigated practical ways of dealing with the consequences of major fires and explosions in underground mines. The results of this research have had a significant positive impact on the mining community by enhancing mine workers’ chances of surviving an underground mine disaster. Today, the Bureau continues to conduct research in mine disaster mitigation. Much of this work has direct application to search and rescue situations, such as: emergency evacuation through smoke-filled or otherwise unbreathable atmospheres, locating and rescuing survivors from rubble piles, and fire fighting in confined spaces. Three USBM research areas are discussed: (1) Life Support -- This effort is directed toward research into and development of closed-circuit breathing apparatus for use in hazardous environments which are likely to be encountered in the aftermath of a mine disaster. (2) Trapped Miner Location -- A mine disaster may result in the entrapment of miners whose normal escape routes are cut-off. This research activity resulted in the development of transportable seismic technology that can be used to locate trapped miners. (3) Mine Fire Diagnostics -- This research involves developing practical techniques for remotely monitoring how the atmosphere inside a mine changes during a fire, in order to estimate the spread and severity of an underground fire. This information is critical in deciding how best to fight a mine fire, or whether it is safe to mount a rescue and recovery mission.

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969