Search Documents

By A. J. Kraemer

This report on research and experimentation by the Federal Bureau of Mines on technologic and scientific problems of the petroleum and natural gas industries presents a resume of work from July 1, 1953, to June 30, 1956. The preceding report, for the fiscal year ended June 30, 1953,3/ indicated continuation of the Bureau's program of petroleum and natural gas research of world-wide significance, which began in 1910. The petroleum and natural gas research of the Bureau of Mines is divided into five main categories: (1) Production of petroleum and natural gas, (2) transportation and storage, (3) petroleum chemistry and refining, (4) thermodynamics, and (5) economics.

Jan 1, 1959

By R. S. Dean

The work of the metallurgical fundamentals section during the past year, representing active experimental investigation or thermodynamic study, may be summarized as the following problem subjects: 1. Low-temperature specific-heat investigations. 2. Development of a method of concentrating gases. 3. Thermodynamic properties of metallic carbides and nitrides, 4. Production of pure chromium from chromium chlorides. 5. Thermodynamic properties of the hydrates of calcium, sulphate. While this list is not identical, with officially designated problems, due to overlapping of subjects and to new developments within specified problems, presentation upon the basis of this subdivision will best serve to review the work of the section.

Jan 1, 1937

By D. E. Wolfson

This report describes the carbonizing properties of the principal coal beds of Allegheny County, Pa., which rank low in the high-volatile A bituminous classification. Seven coal samples from 3 coal beds were selected for study, as follows: 2 each from the Redstone and Pittsburgh beds and 3 from the Upper Freeport bed. Selection was based on estimated reserves. The samples of Upper Freeport and Pittsburgh coals were satisfactory chemically for producing metallurgical coke. The ash contents of the samples of Redstone coal were moderately high. One of the samples of Redstone coal was high in sulfur content, and it would be difficult to upgrade to meet present metallurgical standards.

Jan 1, 1959

By George B. Clark

The purpose of this investigation was to determine the feasibility of designing and testing the elements of a small charge blasting system which will eliminate, or reduce to acceptable levels, most of the undesirable features of current underground drill and blast systems, i.e., 1) air blast, 2) ground vibrations, 3) flying fragments, 4) overbreak and fracture of surrounding rock, and 5) the cyclic nature of drill and blast operations. The experimentation was conducted in tunnels in granite and the results indicate that the basic technical concepts of the project were achieved. The next step is to design, construct, and test a prototype machine.

Jan 1, 1976

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By H. A. Johansen

Recent advances in the metallurgy of chromium have enabled this metal to begin to take its place among the refractory metals. Considerable work is being done on the development of high-temperature alloys containing high percentages of chromium.1/2/ In spite of the relatively large amount of work done on these alloys, little is known of the properties of the pure metal. Information in the literature concerning the tensile properties of pure chromium metal is quite scant. This deficiency maybe explained by the great difficulty of preparing test specimens from such a brittle material, resulting in many losses in each phase of the specimen preparation and testing procedure.

Jan 1, 1954

By Mark Sheppard

This paper is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different tries of primary crushers; and ( 4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of tine fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By A. S. Swanson

The Babb fault vein in Crittenden and Livingston Counties, Ky. (fig. 1), is one of an extensive series of such veins in the Western Kentucky and Southern Illinois fluorspar district. First operated in 1904, the production to May 1, 1944, was estimated at 143,000 tons of fluorite ore. There are five mines (fig. 2) on the Babb fault zone - Guill ,Kentucky Babb, Delhi-Babb, Eagle-Babb and Howard-Barnes. The Bureau of Mines developed four of these properties by core drilling from July 9, 1943, to May 1, 1944. During that period a total of 8,177.8 feet of diamond drilling was completed in 28 holes.

Jan 1, 1950

By A. T. Tye

This paper describing the concentrator practice of the Cananea Consolidated Copper Co. at Cananea, Sonora, Mexico, is one of a series of articles on milling methods and costs being prepared by the U. S. Bureau of Mines. The Cananea concentrator treats 2,400 tons of copper ore per day by preferential flotation, whereby the copper sulphides are floated and the iron pyrite depressed. During the first half of the year 1929 the heads to the concentrator averaged 3.29 per cent of copper, the recovery was 95.74 per cent of the total copper, and the concentrates produced contained 21.44 per cent of copper.

Jan 1, 1930

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By E. R. Palowitch

This report is the result of a series of coal-cleaning tests using a dense-medium cone-type washer. Detailed results are given for 2 tests using a magnetite medium and 4 tests using a pulverized-refuse medium. Approximately 120 float-and-sink tests and over 500 separate chemical analyses were made in conjunction with these tests. In these tests higher recovery efficiencies and sharper separations were obtained when using a magnetite medium, especially on coal sizes below one-half inch. When sizes above 1 inch at low specific gravities of separation are cleaned, the pulverized refuse medium compared favorably with the magnetite medium.

Jan 1, 1956

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By S. M. Runke

An ever-increasing demand for beryllium and beryllium alloys has directed attention to the milling of low-grade domestic deposits as a possible means of supplying part of the Nation's ore requirements. The United States generally produces less than 10 percent of its annual supply. For example, new supply in 1953 was estimated at about 9,250 tons, of which the United States imported 8,500 tons. Domestic production was only 750 tons.2/ Since record high prices for beryl in 1952 and 1953 did not greatly increase domestic product ion, the United States must develop mechanical beneficiation processes to use low-grade deposits and reduce dependence on foreign sources

Jan 1, 1954

By Leonard P. Vitt

This report details the work done to provide the U.S. Bureau of Mines with a customized Wireless Ground Monitor Wireless Ground Monitor was modified as follows: 1. A voltage regulator was added to prevent false trips with line voltage variations. 2. A Ground Wire Trap was designed to eliminate problems with parallel paths and provide spark suppression. 3. A three phase filter was designed to reduce 60 Hz leakage current. 4. A portable tester was designed to permit complete test of installed systems. 5. The design was modified to insure trip with an open ground wire in the event of a failure of any one semi-conductor component.

Jan 1, 1976

By E. Robert Ruhlman

["Phosphate rock" is a broad term applied to natural deposits of minerals valued chiefly for their phosphorus content. More specifically, phosphate rock may be defined as a natural rock containing one or more phosphate minerals, usually calcium phosphate, of sufficient purity and in sufficient quantity to permit its use directly, or after beneficiation, in the manufacture of phosphorus-bearing products. The grade or quality of phosphate rock is expressed either in terms of its phosphorus oxide (P20S) content or the equivalent in tricalcium phosphate (Ca3(P04)2). The trade name for tricalcium phosphate is bone phosphate of lime (B. P. L.).]

Jan 1, 1958

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By R. P. Adams, R. A. Beall

The Bureau of Mines developed a method to melt and cast specimens of hafnium- carbon alloy and studied their properties . A rotating - ladle vacuum or inert atmosphere arc furnace was designed , special electrodes and molds were developed , and operating procedures were worked out for casting small shapes . The cast specimens were evaluated according to their carbon content for melting point , density , microhardness , electrical resistivity , and oxidation resistance . Lattice dimensions were determined , and metallographic specimens were prepared . Photomicrographs were taken of specimens containing 2.72 , 5.50 , 6.47 , 9.97 , 12.8 , and 15.7 weight - percent carbon , and their grain structures were compared .

Jan 1, 1963

By R. S. Dean

In the early days, most smelters were erected in nonarable land and at some distance from settled communities. The movement of population, which resulted in many instances from employment at the smelters, has brought to most smelterman in the United States the problem of preventing damage to plant and animal life in the territory adjacent to the smelters by sulphur dioxide gas (S02). This problem has been met, broadly, in two ways: (1) By diluting and removing the S02 by means of air currents and (2) by converting the S02 to a liquid or solid compound of sulphur and disposing of the compound.

Jan 1, 1937

By R. S. Dean

In the early days, most smelters were erected in nonarable land and at some distance from settled communities. The movement of population, which resulted in many instances from employment at the smelters, has brought to most smelterman in the United States the problem of preventing damage to plant and animal life in the territory adjacent to the smelters by sulphur dioxide gas (S02). This problem has been met, broadly, in two ways: (1) By diluting and removing the S02 by means of air currents and (2) by converting the S02 to a liquid or solid compound of sulphur and disposing of the compound.

Jan 1, 1937