Search Documents

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By A. C. Galvis-Castro, R. Salgado, M. Prezzi, E. Ganju, R. D. Tovar-Valencia

It is generally accepted that the unit shaft resistance of piles in sands is lower for tensile loading than for compressive loading. So far, very little attention has been paid to the influence of the installation method on the tensile-to-compressive unit shaft resistance ratio. The objective of this paper is to analyze the effect of installation method on the ratio of unit shaft resistance in tension to that in compression for a model pile installed in a dense silica sand. To study installation effects, load tests on model piles were carried out in a half-cylindrical calibration chamber with digital image correlation (DIC) capability. The model piles were either jacked in one stroke using a constant rate of advance, or pre-installed into the dense sand samples. Digital images of the model pile and sand were taken during the load test and processed using DIC to obtain the displacement field in the sand. It was found that unit shaft resistance was essentially the same in tension and compression for the pre-installed pile, however for the jacked pile, the unit shaft resistance in tension was approximately half of that in compression. DIC analysis revealed that: (1) during the load test, more displacement occurs in the soil domain for the pre-installed pile compared to the jacked pile, (2) for the jacked pile, the magnitude of displacement in the soil domain is greater in tension than in compression and (3) for the pre-installed pile, the magnitudes of displacement in tension and compression are similar. INTRODUCTION Pile foundations can be categorized into two main types depending on the method of installation: displacement piles (e.g., jacked or driven piles) and non-displacement piles (e.g., bored piles or drilled shafts) (Basu et al. 2010; Salgado 2008). The response of these piles to loading can be studied in the laboratory by means of calibration chamber experiments on model piles that are either jacked into the samples, representing displacement piles (Jardine et al. 2005; Lee et al. 2011; Tovar-Valencia et al. 2018), or pre-installed in the sand sample, representing non-displacement piles(Galvis-Castro et al. 2019a; Le Kouby et al. 2013; Tehrani et al. 2016)

Jan 1, 2019

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By Michael W. Neill, O&apos

The engineering profession generally does not accept vibro-driven piles as bearing piles unless their capacities can be verified by restriking with an impact hammer, which significantly reduces the economic benefits of vibratory driving. In part, the concern for capacity development in piles driven by vibration arises out of observations that vibro-driven piles do not develop capacities equivalent to those driven by impact (e. g., Mosher, 1987). Nonetheless, if capacities are predictable, vibratory installation may be more cost effective than installation by impact, due to savings in time of installation, even if capacities are lower than those of impact-driven piles. Throughout the past few decades, a number of attempts have been made to develop capacity prediction methods for vibro-driven piles, mostly along the same lines as methods for impact-driven piles. That is, (1) totally empirical formulae, (2) power balance / power transfer formulae, and (3) "time domain-nonlinear" (TDN) computational procedures such as the wave equation. Some of the formulae have been based partly on field experience, but the majority have been developed from simple theoretical models with parameters evaluated from laboratory studies. Neither these formulae nor the TDN solutions have been systematically checked (or modified) by recording appropriate field data over a variety of site

Jan 1, 1989

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By Masaki Kitazume

"Abstract The wet type and dry type of deep mixing methods have been developed and widely applied for on-land and marine constructions in Japan. The quality assurance (QA) of the methods has been usually carried out by unconfined compression test on field stabilized soil sampled by core boring in Japan. In some other countries, stabilized soil excavated by the wet grab sampling instead of core sampling is often subjected to unconfined compression test for quality assurance. There are several merits and demerits in each method, but few studies have been carried out to compare the stabilized soil strength of these two types of specimens to discuss their applicability to practical construction. The author has conducted a series of field and laboratory tests to compare the stabilized soil strength and discuss the applicability of wet grab sampling to QA for wet and dry types of deep mixing method.In this study, the wet grab sampling was carried out at two road embankment construction sites where the wet type and dry type of deep mixing were applied. The cement stabilized soil was excavated at the three depths by a wet grab sampler soon after the DM column construction. The test result is compared with the other test data in the previous study to discuss the applicability of the web grab sampling method for QA of cement stabilized soil.IntroductionThe Deep Mixing Method (DMM), an in-situ soil stabilization technique using cement and/or lime as a binder, is often employed to improve soft soils (Kitazume and Terashi, 2013). A variety of factors and their interactions affect the eventual strength of a deep-mixed column, while some of which are controllable (e.g. binder type and dose) by engineers while the others are not (e.g. soil types, ground temperature, etc.; Babasaki et al., 1997). In addition to laboratory mix tests, which in essence are a parametric study to estimate the influence of these factors on a particular soil’s strength, the quality assurance (QA) practice in Japan usually involves unconfined compression test on sampling cores from the stabilized columns after a given curing period. It has been recognized, however, that the ‘field strength’, or the strength of the retrieved core, quf is on average lower than the ‘laboratory strength’, qul, evaluated by laboratory mix test. Also allowing for the inevitable variability, existing guidelines (for example, PWRC, 2004 and CDIT, 2008) recommend the design quf /qul values of, for example, 0.5-1.0 for the CDM (Cement Deep Mixing; a wet-type technique, in which binder is added as slurry) and 0.2-0.33 for the DJM (Dry Jet Mixing; a dry-type technique, in which binder is added as powder)."

Jan 1, 2014

By Ramin Motamed, Farshid Ghazavi, Joseph A. W. Toth

"Post-disaster reconnaissance of areas affected by earthquakes has documented extensive damage to buildings with shallow foundations located in liquefaction-prone areas. Currently, estimation of liquefaction settlement is based on empirical correlations that evaluate settlement in the free-field environment and are based on one-dimensional consolidation. However, observations have shown that liquefaction settlement under buildings can be considerably greater. This research is based on a series of 1- g shake table experiments using a transparent soil box to reproduce liquefaction-induced building settlement. Building settlements were evaluated using a scaled model of a building foundation representing a 1-2 story building. Comprehensive parametric study was carried out to establish the effects of several parameters on free-field and building settlements such as building width and thickness of liquefiable soil layer. The experiments utilized accelerometers and pore-water pressure sensors to monitor ground accelerations and buildup of pore-water pressures in both the free-field and model building footprint. Results of these experiments are compared to available centrifuge tests and field observations and conclusions are drawn with respect to the potential scaling effects. Lastly, this paper discusses the feasibility of installing helical piles as a mitigation strategy to reduce the building settlements by presenting some of the exploratory experimental data obtained from this series of 1-g shake table tests.INTRODUCTIONThe 2010-2011 Canterbury earthquake sequence and the 2011 Great Tohoku earthquake are some of the most recent examples where large numbers of low-story structures sustained damage resulting from liquefaction-induced settlements. This damage has commonly been observed in residential and commercial areas developed over loose, unconsolidated and saturated coarse grained soils resulting from both natural and man-made deposits. Damages incurred from the 2010-2011 Canterbury earthquake sequence occurred in the largely unconsolidated fluvial environment bordering the Avon River in Christchurch (Henderson 2013). Similar damage was also incurred during the 2011 Great Tohoku earthquake where liquefaction of soils occurred in both young alluvial deposits and fill materials (Ashford et al. 2011). Figure 1 presents typical modes of failure to structures resulting from the effects of liquefaction. Current practices in evaluation of liquefaction settlement rely on empirical correlations (Tokimatsu et al. 1987; Ishihara et al. 1992) developed for liquefiable soils in the freefield environment (Dashti et al. 2010a). However, recent observations of the performance of foundations suggest that settlement of rigid shallow foundations in liquefiable soils are commonly greater than those predicted in the free-field. Therefore, new correlations should be developed to better predict the degree of settlement of shallow foundations in liquefiable soils. Current research is beginning to focus on the mechanisms of settlement during liquefaction in regards to confining stress, pore-water pressure and shear stress induced from foundations (Dashti et al. 2010b)."

Jan 1, 2016

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.