Search Documents

By N. A. Gokcen

EQUILIBRIA in the reactions between gases and liquid metals have been the subject of many interesting investigations. The experimental realization of true equilibrium, however, is questionable in certain cases due to the lack of conclusive studies in reaction rates. It -will be shown here that a systematic interpretation of rate studies with the analysis of prevailing experimental conditions leads to valuable practical information. The reactions of particular interest are: H2(g) +S(inFe) - H2S(g) [1] H2(g) +O (inFe) =H2O(g) [21 2H2(g) + SiO2(s) = 2H2O(g) + - (inFe) [3] The usual and perhaps the most convenient method of investigation may be illustrated with reaction 1. A stream of gas mixture consisting of H2 + H2S is passed over or bubbled through the liquid metal at constant temperature. The ratio of H2S/H2 in the entrant mixture is fixed in each experimental run, and, therefore, the composition of melt varies until the establishment of equilibrium. The purpose of this paper is to derive a formula expressing the minimum time required for the establishment of equilibrium and to compare the calculated values from such a formula with the available data. Equations Reaction 1 is used for the purpose of illustrating the derivation. Let E represent the equilibrium and X the nonequilibrium sulphur in weight percent at any time t in minutes. For the sake of simplicity, it is first assumed that E > X although the results are of general applicability without restriction. It has been shown by Morris and Williams' that within a difference of 1 pct S or less, i.e., E-X5 1.00, the value of K'1 = Ph2s/Ph2.S% is very nearly constant. The maximum ratio of available Ph2s/Ph2 = H,S/H,, from which sulphur can be absorbed by metal, is equal to H2S/H2 in equilibrium with E (which equals H2S/H2 in the entrant gas), minus H,S/H, in equilibrium with X. Thus: Available H2S/H2 = EK'1 - XK'1 [4] Eq. 4 expresses that sulphur can be absorbed by metal from the H2S/H2 in the entrant gas until the gas leaving the metal assumes a value of H2S/H2 which is in equilibrium with the dissolved sulphur X at that time. H,S constitutes up to approximately 1 pct of the gas mixture. Its disassociation into H2 and SL is about 1 pct at 1600°C, hence, the H2S/H2 impinging on the surface of metal is very close to that in the entrant gas. The rate of flow of hydrogen entering the reaction chamber is kept constant experi-

Jan 1, 1954

By B. McNulty

The Niblack polymetallic volcanogenic massive sulfide deposits are located on Prince of Wales Island in southeast Alaska, approximately 50 km southwest of Ketchikan. The property hosts a number of polymetallic volcanogenic sulfide occurrences within the folded Lookout rhyolite volcanic succession. The Lookout deposit is the primary focus of current resource delineation and contains an indicated resource of 4,136,000 tonnes at 1.13% Cu, 2.32 g/t Au, 2.27% Zn, 38.70 g/t Ag and an inferred resource of 1,736,000 tonnes at 1.09% Cu, 1.77 g/t Au, 2.02% Zn, and 25.52 g/t Ag as of March 2011. Sulfide mineralization is interpreted to have formed sub-seafloor, within permeable felsic fragmental volcanic rocks. Sulfide minerals of economic interest include chalcopyrite and Fe-poor, Zn-rich sphalerite. Of considerable importance, the Lookout deposit contains elevated gold that occurs as inclusions within the base metal sulfides.

Jan 1, 2012

By Wang Dawan

During the process of arsenic bearing gold concentration biooxidation, the content of chloride ion in water is a very important factor to the activity of bacteria and the oxidation of sulfide minerals. In this paper, the influence of underground mine water with different chloride ion content to the biooxidation of arsenic bearing gold concentration and the limit of chloride ion content to bacteria were summarized. These results indicated if the content of chloride ion was less than 1.2g/L, the bacteria?s ability to oxidize sulfide minerals was little affected, and if the content of chloride ion were increased to 2g/L or more, the activity of bacteria was seriously restrained, and if the content of chloride ion were increased to 4g/L, the activity of bacteria was absolutely restrained. So, as the content of chloride ion in water was cumulated to 2g/L or more in biooxidation plant, the water must be refreshed to maintain normal production.

Jan 1, 2008

By Seth C. Schaefer

[As part of the Bureau of Mines effort to provide thermodynamic data for advancement of mineral resources technology, the standard Gibbs energies of formation (?G°f) of MnS (manganese sulfide) and Fe0.9 S (pyrrhotite) were investigated with a high-temperature galvanic cell employing stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnS, MnO, S02 (g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt with the overall cell reaction MnS (s) + 1.5 02 (g, 0.0114 atm) = MnO (s) + S02 (g) . (1) These results give the standard Gibbs energy of formation of MnS for the reaction Mn (s) + 0.552 (g) = MnS (s) (2) ?G°f = -66.487 + 15.19 x 10-3T±0.207 kcal/mole (896.4 - 1,208.1 K) (3) where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, FeO .9S, Fe304 , S02 (g, 1 atm) //Zr02//02 (g, 0.0114 atm) , Pt with the overall cell reaction 10/3 FeO .9 S (s) + 16/3 02 (g, 0.0114 atm) = Fe.,04 (s) +10/3 S02 (g). (4) These results yield the standard Gibbs energy of formation for the reaction 0.9 Fe (s) + 0.5 S2 (g) = Fe0.9 S (s) (5) ?G°f = -35.229 + 12.67 x 1073T+-0.104 kcal/mole (839.5 - 1,086.6 K). (6) A third-law analysis of MnS data yields a standard enthalpy of formation (AH°f) for the reaction Mn (s) + S (rh) = MnS (s) (7) ?H°f298 = -51.16±0.21 kcal/mole (8) A similar third-law analysis for Fe0.9S data yields a ?29°f298 for the reaction 0.9 Fe(s) + S(rh) = FeO .9S(s) (9) ?HO\°f298 = -24.01±_0.15 kcal/mole. (10) ]

Jan 1, 1980

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

By W. A. Anderson, R. F. Mehl

RECRYSTALLIZATION of cold-worked metals has long been known to proceed by a process of nucleation and growth.1 When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.' Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrystallization is thus analyzed into its two component rates.2 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;* values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of N and G over appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By D. A. R. Kay

Phase stability diagrams are used to predict the abilities of lanthanum and cerium oxides to desulfurize coal gasification products in the temperature range 800-1000 C. Results of desulfurization studies in laboratory fixed bed reactors illustrate the effects of i) sorbent preparation, ii) input gas quality and iii) temperature, on the desulfurization reaction. 2CeO(2-x)(s) + H2S(g) + (1-2x)H2 = Ce2O2S(s) + 2(1x)H2O(g) The results of desulfurization/oxidation regeneration cycles are also reported.

Jan 1, 1989

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By M. J. Ginsberg, N. A. Gokcen

THE preliminary study of electrochemical desul-furization performed by Ohtani and Gokcen1 left a number of points concerning the process to be investigated. Two of these were i) the determination of the effect of greater current and voltage on the desulfurizing Flower of acid slags (% CaO/% SiO2- 1) and ii) the possibility of the loss of silica in slag by the reactions 2C (in metal) + SiO2 (slag) = Si (in metal) + 2CO(g) and C + SiO2 (in slag) = SiO(g) + cO(g) proceeding to a point at which the composition of the slag was sufficiently altered toward the basic side so a1.s to noticeably affect the rate of de-sulfurization. The apparatus and the procedure used in the present investigation were the same as those used by Ohtani and Gokcen, except the control circuit was connected to 120 v dc instead of 24 v dc and thereby allowed greater freedom in choosing the values of both current and voltage. The graphite crucible containing the melt and serving as the cathode was 3-in. high, and was of 1 1/2-in. ID with a graphite bar of 3/8-in. diam and 8-in. length threaded into the bottom for electrical connection. This was placed into a magnesja outer crucible with a hole in the bottom and alumina insulation was packed between the two crucibles. A charge consisting of 180 g of

Jan 1, 1962

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By S. k. Kim, H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a promising secondary resource of platinum group metals (PGMs), which are being extensively used in automobiles catalytic converters to control the hazardous gaseous emissions (CO, NOx and hydrocarbons). Several pyro or hydrometallurgical routes has been employed to recover PGMs from such spent materials but there is no proper process for recovering the other constituents metals. Therefore, it causes the loss of other major constituents like, Al and Mg along with rare earth metal Ce. In the present study, we investigate the dissolution of Al and Mg using sodium hydroxide (NaOH) roasting followed by a sulfuric acid (H2SO4) leaching; thereby concentrating the PGMs and Ce in leached residues. The effect of roasting temperature, time and amount of NaOH were varied. Subsequently, the dissolution behavior of metals in H2SO4 as a function of acid concentration was investigated from the roasted samples. At an optimal condition for roasting at 600°C with 1:1 NaOH-to-catalyst ratio and 60 min duration, the maximum of Al and Mg were dissolved in 1 M H2SO4 solution at ambient temperature (~25°C). Thus obtained leached residues containing enriched PGMs and Ce content can be treated separately for the recovery of these high-value metals.INTRODUCTION Spent auto-catalyst has been considered as a potential resource for recovering the platinum group metals (PGMs) (Jha et al., 2013). The commonly used auto-catalyst is made of cordierite (2MgO.2Al2O3.5SiO2) in which the chloro complexes of PGMs are impregnated onto the surfaces of porous washcoat of alumina substrate (Aberasturi et al., 2011). The average concentration of PGMs in ore are 2-4 g/ton for Pt, 7-2 g/ton for Pd and 0.2-0.5 g/ton for Rh, whereas, an individual catalytic converter weighing about 1 - 2 kg contains on average 1.56 g Pt, 0.62 g Pd and 0.156 g Rh (Upadhyay et al., 2013). Moreover, recovery of PGMs from spent auto-catalyst offers other advantages like, simple process, low cost and less pollution, as compared to recovery from primary resources (Dong et al., 2015).Therefore, technologies to recover PGMs from spent auto-catalyst has become attractive in the recent past and their recycling contribution has been accounted for 35% Pt, 26% Pd and 36% Rh of the quantity consumed in the production of auto-catalysts (Johnson Matthey, 2016)."

Jan 1, 2017

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By N. J. Wagner, D. G. Modiba

There is currently limited knowledge concerning South African coal deposits as hosts for rare earth elements (REE). This project aims to determine the concentration of REE, including yttrium and scandium (REY+Sc) in various coal seams and adjacent sediments in borehole cores from the Ermelo, Witbank, and Waterberg coalfields in South Africa. Coal petrography (maceral count and vitrinite reflectance), XRD, XRF, sequential chemical extraction procedure (SCEP) before ICPMS, and mineral liberation analysis (MLA) were conducted on the coal and associated sediment samples. The coals were inertinite-rich, medium-rank bituminous coal, with moderate to high ash content. The two dominant minerals in all the coalfields are kaolinite and quartz, except for sample ZBS2M, where dolomite was dominant. The dominant major oxides are Al2O3, SiO2, Fe2O3, and CaO, which concur with the XRD results. The ICP-MS results following SCEP indicated that both coal and the associated sediments were light REY+Sc dominant. There was also an elevation of medium REY+Sc in the Witbank coal’s associated sediment samples. Notably, the samples with the highest REY+Sc results were the sediment samples. The Waterberg samples had the lowest REY+Sc from both the coal (less than 2 μg/g to 7 μg/g) and associated sediments (2 μg/g to 15 μg/g). While the highest REY+Sc was yielded from the Witbank-associated sediments (500 μg/g to 2,500 μg/g). The carbonate fraction step proved to be the most successful leaching step, as most REY+Sc was recovered in that step for all coalfields. In addition to the carbonate fraction, the silicates and sulfide fraction in the Witbank samples, and the ion-exchangeable fraction for the Waterbergassociated sediments samples proved successful in leaching out the REY+Sc. MLA determined that monazite and xenotime in all the coal samples were the REY+Sc-bearing minerals.

Nov 6, 2024

By Ronald T. Mayerle

The Condrey Mountain RARE II area lies mostly within the Elliot Creek mining district, a significant producer of gold from placers, and gold, Silver, copper, and minor soapstone from lode deposits. No mineral production has occurred within the study area; no resources are known in the area. However, significant resources in lode and placer deposits are just outside the west and northwest boundary of the area. The Blue Ledge Mine (fig. 1, no. 15) adjacent to the western boundary, is reported to contain 226,000 ton; (205,000 t) of identified resources averaging 0.05 oz gold per ton (1.7 g/t), 2.16 oz silver per ton (/4.0 g/t), 3.5 percent copper, and 3.95 percent zinc. The mine has produced 11,131 tons (10,114 t) of ore that yielded 1,026 oz (31,908 g) of gold, 58,431 oz (1.8 million g) of silver, and 2.7 million lb (1.2 million kg) of copper. Exploration is currently underway at `he mine and vicinity, including part of the study area.

Jan 1, 1983

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By Sheng-hai Yang

The ultrafine, monodispersed, spherical cobalt powder has been fabricated by reducing cobalt hydroxide with glycol. It were investigated that the effect of NaOH concentration on the reaction rate and the effects of the concentration of cobalt hydroxide and surfactant on the morphology and particle size. The particles were characterized by the X-ray diffraction(XRD), scanning electron microscope(SEM), laser diffraction particle size analyzer and BET specific surface analyzer respectively. The XRD shows that the cobalt powders exist mostly in face centered cubic (fcc) structure, a little in simple hexagonal. The cobalt powders prepared at Co(OH)2150g/L, NaOH 40 g/L and surfactant 30g/L, its average particle size, specific surface area and cobalt content, were 0.88µm, 2.705m2/g. and more than 99.5% respectively.

Jan 1, 2006

By C. E. Birchenall, H. M. Schadel

THE purpose of this study was to measure the vapor pressure of silver as the first step in the determination of activities in silver alloys and to test the limitations of the method adopted. In order to work at low pressures, below 2x10-2 mm of mercury, the orifice effusion technique was employed. To shorten the time of collection of silver from the atomic beam, radioactive silver (Ag110) was used as a tracer. The rate of effusion of a monatomic vapor from an "ideal" orifice, where the thickness of the orifice edge is negligible compared with the orifice diameter, can be readily calculated from the kinetic theory of gases, G = vM a p/v2pRT where G is the weight of material effusing from the orifice per unit time; p is the vapor pressure at oven temperature, T; R is the gas constant; M is the molecular weight of the vapor; and a is the orifice area. Consolidating constants and expressing as the weight of material effusing from the orifice in a period of time, t, (5.83)(10-2) (vM) (a) (t) (p)/vT where GT is total weight of monatomic vapor effused (g); M is molecular weight of the effusing tracer vapor; a is orifice area (cm2); t is time of effusion (sec); p is vapor pressure of effusing material (mm of Hg); and T is oven temperature (OK). The vapor effuses from the orifice in a hemispherical pattern, and the intensity of the beam in any direction is given by the cosine distribution law.' Considering this, the weight of effused material can be calculated from the amount of material passing through a circular collimator intersecting the beam. If such a collimator is in a plane parallel to the plane of the orifice and with center on the normal to the orifice center, GT = G?/1-cos2? = G?/sin2? where G? is the weight of effused material passing through the collimator, and 0 is one half the apex angle of the cone defined by the collimator circumference and the orifice center. Reducing eq 3 to the more directly measurable quantities of orifice to collimator distance, d, and collimator diameter, D, the expression becomes,

Jan 1, 1951

By T. Karalis

Perlite is a generic term for naturally occurring siliceous rock. It is a form of natural volcanic glass the main constituent of which is amorphous silica (70-76%). Perlite, when heated rapidly to its softening temperature range, expands from four to twenty times its original volume, due to the presence of 2-6% ?combined? water, in a manner similar to popcorn as the H2O molecules vaporize and create countless tiny bubbles, which account for its exceptional physical properties: light weight (30-150 kg/m3), low thermal conductivity, cellular structure, in general. These properties make perlite adaptable for numerous end-uses, which can be distinguished into 2 categories: Expanded perlite applications in: a) Construction Materials market (e.g. Acoustical Tiles, light-weight insulating Mortars, self-levelling Concrete), b) Agriculture (e.g. Hydroponics), c) Food and Chemical industry (e.g. Filtration Media, Filler, etc.), d) Insulation and Heat resistance technology (e.g. Cryogenic vessels, Refractory Bricks, etc.). Unexpanded Graded perlite applications in: a) Phosphoric Fertilizers industry (additive in H3PO4 production), b) Foundry technology (slag-aid, insulating and heat resistance agent).

Jan 1, 2006