Search Documents

Terminology. The term potash originated in "pot ashes" produced by burning wood to ashes in iron pots and then leaching out the soluble salts, chiefly potassium carbonate, from the residue. In modern usage potash is a generic term for various potassium salts used in agriculture and industry. More specifically, it denotes the oxide of potassium, K2O, and the content of potassium in ores and products is stated as weight percent of K2O present. Its salts are commonly referred to as muriate of potash, sulfate of potash, etc. The presence of an adequate supply of available potassium in the soil promotes the health and improves the quality of the plant. insures greater efficiency in photosynthesis, increases resistance to certain diseases, offsets the effect of an oversupply of nitrogen, and helps the plant to utilize soil moisture more advantageously. ("Soils and Men," U.S. Dept. of Agriculture Yearbook 1938.) Occurrence. Potassium ranks seventh among the elements in abundance. It is estimated to constitute some 2.6% of the lithosphere and is found in soluble forms in the oceans, lakes, rivers, and subsurface waters. It is also an important constituent of plant and animal life. Commercially significant accumulations of potassium salts occur in underground deposits formed in past geologic times by evaporation of ancient bodies of saltwater, inland drainage basins, and shallow sea lagoons. The potash content of such waters was the end result of weathering and leaching of insoluble potash-bearing aluminosilicates, such as feldspars, micas, leucitcs, and others. The concentrations of potassium salts in the natural brines of some lakes in the arid and semiarid regions of the continents are also important as sources of potash; the brines of the Dead Sea in Asia Minor, the Great Salt Lake in Utah, and Searles Lake in California typify such concentrations. Every continent has major potash deposits as listed in Table 1 adopted from Cawley.1

Jan 1, 1985

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By John Chapman, Daryl Hockley, Michael Paul, Silvia Jahn

As part of the waste characterisation program to address site reclamation, WISMUT GmbH initiated 56 columns operated as large-scale humidity cell tests. The columns were initiated to assess the acid generation characteristics of waste rock from 14 waste rock piles distributed around the site. Of the 56 tests, 11 are ongoing and have been operational in excess of 160 weeks. The results to date from these long-term tests are surnrnarised. In particular, the methods for, and importance of, establishing the availability of the carbonate neutralisation potential and acid generation potential respectively, are discussed. Geochemical controls on uranium, and the conformity between the geochemical models MINTEQA2 and EQ3/6 in assessing these controls are discussed. Testing indicates that waste rock with an MS-NP:AP ratio in excess of about 2.7 should result in net neutral pH conditions.

Jan 1, 2000

By E. Fernandez

HIGH SPEED RAILWAY NETWORK Spain is a very adequate country to develop the high speed railway network thank to its geographical feature which has a 600km long radius, from Madrid- the capital that covers mostly the whole country. Therefore, the railway is a major competitor of the airline. In Spain, the new access to the north and northwest is nowadays the most important railway project which will allow a significant saving of time in the near future to the central plateau and the northern territories. Time savings as well as strict environmental considerations have been the main objective of various studies during the last decade leading to Guadarrama and Pajares tunnels as ones of the optimum solutions. Cordoba-Malaga high speed railway, the extension of the present Madrid—Sevilleline, through the Abdalajis range and the rail project to cross oriental Pyrenees between Spain and France are another two samples of large tunnels currently underway. In these four projects, the ground already encountered and to be soon encountered is highly variable, from very hard granite and gneiss in Guadarrama and Pertus to very poor argillite in Abdalajis, shale in Pajares and schist in Pertus. A number of faults are also expected. Hence, double shield hard rock TBM has been chosen. Figure 1 shows a general scheme in four projects. These four projects represent a total of 2 × 68 km of which 87 km are under DRAGADOS contracts. PROJECTS UNDERTAKEN BY DRAGADOS Guadarrama Tunnels This project is the longest twin tunnel with 28.377km, in Spain and considered one of the longest in Europe. The operating speed will be 300 km/h. This tunnel will link Madrid and the north territories through Guadarrama range. (Figure 2). The south portal is placed at el. 997.8m above the sea level. The tunnel starts with an inclination of 3‰, increasing until 15‰. After 6,620m length, the tunnel passes under the Morcuera ridge with an overburden of 960m. After 13,400m length, the elevation is 1,024m which is the highest point, and then the tunnel declines with a slope of 9.5‰, 2‰ and 19‰ until the north portal in Segovia province. At the border of Madrid and Segovia that is Penalara peak, the maximum

Jan 1, 2005

By Robert D. Hansen, Richard R. Klimpel

INTRODUCTION A very important factor in froth flotation is the use of surface-active chemicals to form a froth in which minerals or coals are retained, thus allowing for valuable component enrichment. In coal flotation reagents (frothers) specifically designed to provide an efficient froth are employed. It is this group of chemicals that will be the primary emphasis of this paper. Despite the importance of frothers, surprisingly little systematic scientific work has been performed with the goal of quantifying frother mechanisms and the influence of particles on froth stability. Based on direct experimental observations in both batch laboratory and continuous large-scale flotation cells, the use of a frother significantly increases first, the possibility of a particle- bubble contact, and second, the efficiency of sticking after such a contact. Thus, a major role of a frother is to significantly increase the rate of flotation. This rate modification by a surface-active agent occurs through several observable mechanisms including the formation of a froth of relatively consistent character (bubble size and bubble density) under a variety of operational conditions, an increase in the ability to disperse air in the flotation cell, a reduction in the rate of coalescence of individual bubbles in the cell, and a decrease in the rate of bubble rise to the pulp surface. It will not be the intention of this paper to exhaustively list all frother accomplishments related to research, development and use in coal flotation. Rather, the authors will attempt, based on their experience, to present a technology overview of the role of frothers in the chemistry of flotation as successfully practiced at the industrial level. A very useful framework for flotation is the concept suggested by Klimpel (1984, 1984a) of viewing flotation as a system consisting of three major components: chemistry, equipment and operating variables. This is illustrated in Figure 1. A major point of this figure is that flotation is a highly interactive system with many technical and economic combinations of component settings available to operators to achieve a given goal. Sometimes simultaneously changing various component settings will reinforce a particular attribute. Also various component settings can cancel or counteract each other if changes are not chosen wisely. Thus, coal flotation must be viewed by the plant operator as a complex system with the economic/technical optimization of a given flotation process being directly related to the operator's knowledge of how his particular flotation system behaves as a function of the major control variables he has at his disposal. Typical important component settings in coal flotation are collector dosage, frother type and dosage, air flow rate, feed rate, particle size, pulp density, and the surface oxidation conditions of the coal. Because of the above complexities, it is sometimes assumed (especially in laboratory studies) that the choice of frother type and dosage is not as crucial as some of the other factors such as collector type and dosage (e.g., Leja, 1982). Detailed plant level testing of all of the factors of Figure 1 performed in recent years, Klimpel (1980, 1980a, 1982, 1984, 1984a), Hansen (19861, Klimpel, Hansen and Meyer (1982), simply do not support this assumption. The above testing has shown rather clearly that certain frother chemical structures consistently exhibit predictable performance characteristics in both mineral and coal flotation. In addition, significant changes in both rate and recovery can be expected. In the remaining sections of this paper, the following topics will be covered: requirements of chemicals capable of use as frothers, types of chemicals used commercially as frothers, some general performance characteristics of existing commercial frothers, and recent work in developing new frother chemical structures.

Jan 1, 1986

By M. Yavuz

Underground mining method selection (UMMS) is one of the most important issues in mining engineering. Underground mining method should be primarily selected to make use of underground resources optimally. It is nearly impossible to change the mining method once selected by the reasons of rising costs and mining losses. Because of these reasons, UMMS process is extremely important in mine designs and economics. The strategy of underground mining method selection has been studied by different researchers in the literature. Boshkov and Wright (1973) proposed a classification system; Morrison (1976) suggested a selection chart; Laubscher (1981) proposed a selection methodology; Nicholas (1981) presented a classification system; Hartman (1987) developed a selection chart and Miller-Tait et al. (1995) modified the Nicholas? system and developed the UBC mining method selection process. In reality, UMMS is one of the important Multiple Attribute Decision Making (MADM) problems and mining engineers have always some difficulties in making the right decision in the multiple criteria environment. To make a right decision on UMMS, all known criteria related to the mining method selection should be analyzed and the problem solved according to suitable decision making techniques. A review of the literature reveals that decision making techniques have been used for UMMS applications. Kesimal and Bascetin (2002), Bitarafan and Ataei (2004), Bascetin et al. (2006), Alpay and Yavuz (2007), Karadogan et al. (2008) and Samimi Namin et al. (2008) used decision making techniques in UMMS applications. In this paper, two different MADM methods: Analytic Hierarchy Process (AHP) and Fuzzy Multiple Attribute Decision Making (FMADM) are applied to select the optimal underground mining method for a chromite mine and final solutions are then compared. THE AHP METHODOLOGY The AHP method developed by Saaty gives an opportunity to represent the interaction of multiple factors in complex unstructured situations (Triantaphyllou, 2000). The method is based on the pair-wise comparison of components with respect to attributes and alternatives. A pair-wise comparison matrix n×n is constructed, where n is the number of elements to be compared. The method is applied for the hierarchy problem structuring. The problem is divided in to three levels: problem statement, object identification to solve the problem and selection of evaluation criteria for each object. After the hierarchy structuring, the pair-wise comparison matrix is constructed for each level where a nominal discrete scale from 1 to 9 is used for the evaluation as shown in Table 1 (Saaty, 1980; Saaty, 2000). The next step is to find the relative priorities of criteria or alternatives implied by this comparison. The relative priorities are worked out using the theory of eigenvector. For example, if the pair comparison matrix is A, then, [Amax=××- [1] ] To calculate the eigenvalue ??max? and eigenvector w=(w1, w2,..., wn), weights can be estimated as relative priorities of criteria or alternatives. [ ] Since the comparison is based on the subjective evaluation, a consistency ratio is required to ensure the selection accuracy. The Consistency Index (CI) of the comparison matrix is computed as follows: [CImax--= [2] ] where ?max is maximal or principal eigenvalue, and n is the matrix size. The consistency Ratio (CR) is calculated as: [CR= [3 ] where ?RI? Random Consistency Index. Random consistency indices are given in Table 2. [ ] Table 2. The consistency indices of randomly generated reciprocal matrices As a general rule, a consistency ratio of ?0.10? or less is considered acceptable. In practice, however, consistency ratios exceeding ?0.10? occur frequently. THE FMADM METHODOLOGY The FMADM methods have been developed due to the lack of precision in assessing the relative importance of attributes and the

Jan 1, 2009

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By Brenda J. Wolfe

Following successful laboratory and pilot plant investigation of dewatering characteristics of molybdenum concentrate produced by a Chilean copper/moly producer, two (2) DENVER SALA 500 Series Tube Press Filters were installed in 1994 to handle the total production volume. Moisture requirements in the filter cake have been consistently met, eliminating the need for thermal drying after filtration. Operating data and Tube Press Filter are described herein.

Jan 1, 1995

By A. W. Khair, S. S. Peng

Background The mine is located in Ebensburg, Cambria County, PA. Cambria County is located within the Allegheny Mountain section of the Appalachian Plateau Province. The geologic structures in the mine area included folds, faults, joints and cleats in the coal. These geologic structures seem to have genetic relationships with the Allegheny Front (lannacchione and Puglio, 1979). The mine's geologic structures have been influenced mainly by Ebensburg Anticline and Wilmore Syncline (Watson, 1979). Current longwall panels lay along the western limb of the Wilmore Syncline oriented south 30° west. Surface topographic relief in the area is less than 152 m (500 ft) and overburden thickness varies from 183 to 244 m (600 ft to 800 ft). The coal seam in the mine is part of the Lower Kittanning Formation. The thickness of the B-seam is the subject of discussion. It varies from 1.2 to 1.5 m (48 to 60 in.) and consists of two parts. The lower part is 1.1 to 1.2 m (44 to 48 in.) of soft coal and the remainder is bony coal. The coal seam dips slightly from 0° to 6° to the east-south direction. Panel entries are driven 61 m (200 ft) wide, consisting of three 5.5 m (18 ft) wide entries and two pillars 24.4 x 30.5 m (80 x 100 ft) centers. The mine has a history of cutter roof problems in the entries (Fig. 1) that has delayed the advance rate of entry development considerably and the cost of maintaining those entries is very high due to the requirement of very heavy artificial supports (Fig. 2). Due to excessive convergence in the headgate, installation of additional support and often resetting of steel beam, to provide enough clearance, in these entries imposed additional delay during the retreat of the longwall face, as the shearer cuts coal adjacent to the headgate and shield support at the headgate needs to advance under the steel beams (Fig. 3). Methodology Extensive underground observation indicated that roof cutter [ ]

Jan 1, 1992

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980

By M. Karmis

According to international projections and future energy scenarios, coal will continue to be a prominent fuel for the next 25 years. In fact, in many regions around the world, coal is expected to dominate the electricity sector until the year 2030. At the same time, with instability and volatility of oil prices, coal is also positioned as an alternative feed stock for conversion into liquid fuels. Energy economists maintain that coal liquefaction is viable at crude oil prices of $35 or more per barrel. Depending on technology and coal composition, 1 ton of coal can produce 1 to 4 barrels of oil. Increased coal production and the expanded utilization of coal also raise environmental concerns regarding greenhouse gases and the problem of handling CO2. Carbon sequestration research, currently conducted in many parts of the world, has demonstrated considerable potential for C-storage in unminable coal seams. Such geologic storage, when possible, can also be integrated into an enhanced coal bed methane recovery process Can coal fuel power plants and industrial facilities, provide diesel and other liquids and, at the same, also be used as a medium for permanently storing CO2? This presentation will provide a global perspective on these questions and stress on the need to reconsider, or even redefine, coal as the fuel for the future.

Jan 1, 2006

By J. Yao

Synthetic indium-bearing zinc ferrite (IBZF) was mechanically activated by a tumbling mill. Subsequently, the behavior and kinetics of leaching zinc and indium from the initial IBZF and activated IBZF in sulfuric acid solution were investigated. The results demonstrate that the tumbling ball milling enhances the leaching reactivity of IBZF and increases the zinc and indium extractions. The reaction temperature and H2SO4 concentration have an important effect on leaching zinc and indium from the initial IBZF and activated IBZF. The kinetic model -ln(1-x) = kt was used to describe the kinetics of leaching zinc and indium from the initial IBZF and activated IBZF and to calculate the kinetic parameters. The tumbling ball milling causes a decrease in activation energy and reaction order, which indicates that the dissolution of IBZF after mechanical activation by a tumbling mill becomes less sensitive to temperature and H2SO4 concentration. For the zinc leaching, the activation energy decreases from 73.9 to 70.3 kJ/mol and the reaction order decreases from 0.72 to 0.70. For indium leaching, the activation energy decreases from 78.1 to 73.5 kJ/mol and the reaction order decreases from 0.82 to 0.69. It is found that the dissolution rates of the initial IBZF and activated IBZF are controlled by surface chemical reactions.

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By S. Hartman

The Escalante Silver Mine in Southwest Utah produces an average of 71.000 kg (2.3 million troy ounces) of silver dore annually. Precipitates from a cyanide leach circuit are treated by either acid leaching prior to fusion or a direct fusion with nitre. Process development, plant experience, and a comparison of both methods will be discussed. Plant experience from the custom treatment of a gold/silver precipitate containing matte producing elements will also be covered.

Jan 1, 1989

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"INTRODUCTION The design, development, fabrication, and test of cryogenic breathing apparatus is part of a much larger effort funded by the National Institute for Occupational Safety and Health (NIOSH) and managed through a Space Act Agreement with the National Aeronautics and Space Administration (NASA) at the Kennedy Space Center (KSC) in Florida. This effort is designed to create cryogenically based life support equipment that is responsive to the needs of miners as required by the Miner Act of 2006. Our goal was to design and build a liquid air based self-contained breathing apparatus (SCBA) that lasted 2 hours and would be used for the egress of miners during a mining accident and be refillable while worn. Therefore, the current report describes tests of an Advanced Cryogenic Breathing Apparatus (termed the ACryoBA) designed to provide miners egressing an emergency situation with a two-hour open-circuit SCBA. The ACryoBA utilizes low pressure cryogenic liquid air instead of high pressure compressed air commonly used in most commercially available SCBA. The ACryoBA can also be self-filled from strategically placed Cryogenic Air Supply and Fill Stations (CryoASFS) initially, and thereafter on the egress route approximately every 1 hour and 30 minutes with a 30 minute air reserve. The ACryoBA evolved originally from a one hour Liquid Air Pack (LAP) developed in the 1980’s for Space Shuttle Rescue forces allowing for longer duration and cool air (Figure 1). It was used successfully for many years, through the end of the Space Shuttle Program. The first attempt at a mine egress pack was the Cryogenic Breathing Apparatus (Figure 2). It was to have a low profile, two hours of breathing, attitude independence, and a simple rapid refill while in use. The CryoBA met the two hour criteria, but with difficulty due to excessive heat leakage caused by the dual 4 liter Dewar design. Much of the stored air was lost as it vaporized faster than it could be used. However, the pack was successful in demonstrating both attitude independence and a simple rapid refill capability. The ACryoBA project was designed to continue the progression and address the deficiencies in the CryoBA. The ACryoBA pack was designed to last 2 hours. It minimizes the heat leakage with a single Dewar and thereby requires less liquid air. The single Dewar design also minimizes weight, making it much more manageable by the user (Figure 3). The ACryoBA complies with 42 CFR part 84 NIOSH certification test requirements. One critical requirement for the ACryoBA is operation in positions other than vertical for periods up to 1/4 (i.e. 30 minutes) of the rated service life of 2 hours; this was accomplished by use of new technology called the “attitude independent pickup” which is abbreviated “AIP.” The AIP, developed by BCS Life Support LLC (patent #8,899,226), has a tube going from the top flange down through the center of the Dewar. At the end it has a flexible bellows and a weighted end. Due to the flexible nature of the bellows, the pickup at the end is free to rotate and follow the liquid level around within +/- 90o of vertical."

Jan 1, 2016

By J. C. Norman

The boron review did not arrive in time for publication in the June issue. The United States was the world's largest producer and consumer of boron compounds during 1992. The US Bureau of Mines estimated that boron mineral concentrate and chemical production in the United States totaled 1Mt (1.1 million st) in 1992, yielding 521 kt (574,000 st) of B203 for a total estimated value of $333 million. That was about 20% less than 1991 revised production figures, and less in value by $107 million. The United States continues to provide essentially all of its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. Domestic employment in the mining and beneficiation of boron products in 1992 was about 900 people, the same as in 1991. In 1988, 1250 people worked in the boron industry. The Bureau estimated that total world production of boron in 1992 was about 3 Mt (3.3 million st), or about 1.2 Mt (1.3 million st)of B2O3. World production in 1992 was about equal to revised 1991 levels. US production Mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals. US producers, in order of quantity of production, included:

Jan 1, 1993

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018