Search Documents

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system's electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By I. Liebman

The Bureau of Mines conducted research to develop triggered barrier systems for protection against gas explosions that can occur in underground coal mines during the use of continuous miners. Several extinguishing agents were tested in barriers at a simulated mine face. Water, powered by pressurized nitrogen, was found to be efficient in stopping fully developed gas explosions, but it had little effect against the explosion during its incipient stage. Hybrid combinations of currently known extinguishants, however, were successful against incipient explosions. Three hybrids that were developed and tested consisted of Halon 1301, combined with either an aqueous foam solution, water, or a dry chemical powder. The three hybrids were found to be more efficient than any constituent alone. Results of the tests point to a synergism between the hybrid components, and indicate that the Halon aids in dispersing its constituent and also converts the aqueous foam solution into a stable fine foam and the water into fine drops.

Jan 1, 1978

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By E. D. Calvert

This Bureau of Mines report discusses the electric-arc reduction of zirconium and hafnium oxides with carbon yielding a metal-metallic carbide mixture. The carbon to oxide ratio in the feed determines the metal to carbide ratio in the product. A sample of this product was produced -or testing as a feed for the deBoer iodide-dissociation process. A new technique for producing pure carbides is described, which uses the intense heat of the arc to volatilize the carbide. The condensed vapor form , crystals of nearly stoichiometric carbide, INTRODUCTION This research examines the preparation of refractory metal carbides in the controlled atmosphere electric-arc furnace.

Jan 1, 1962

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By G. W. Jones

In a previous report,6/ results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.1 cubic feet when the number of ventilation openings in the cover was varied from no openings to a maximum of 48. The result s showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC&apos;) data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976

By W. M. Dressel

This Bureau of Mines report describes a shaft closure demonstration project in which 11 inverted pyramid-shaped plugs were used to plug abandoned open mine shafts in Galena, KS, The inverted pyramid-shaped forms, fabricated from steelplate, were designed so that the inverted base would be larger, by 4 ft on a side, than the approximate size of the shaft opening at the surface residuum-solid rock interface. After the surface openings of the shafts were trimmed with a backhoe, the steel forms, complete with reinforcing, were lowered into the openings and filled with concrete; the remaining portions of the openings above the plugs were backfilled to slightly above the surrounding surface level with waste rock and soil. Location and elevation monuments were installed for long-tern evaluation of the success of the project.

Jan 1, 1985