Search Documents

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By William G. Gruzenaky

The separation of yttrium and the individual rare-earth elements (lanthanons) from mixtures in which they occur has been a difficult problem through-out the years. Because of the increased interest in the various uses of these metals, the economy of their production may become of great importance. Studies relative to this problem, undertaken at the Federal Bureau of Mines Albany Metallurgy Research Center, resulted in the development of a solvent extraction method by which yttrium can be separated from the rare-earth metals. A separation factor of 10.93 was obtained between yttrium and cerium from a single-stage extraction, and a factor of 1.78 was obtained between yttrium and erbium from a multistage system. The valuable metals were extracted from euxenite by caustic soda fusion or by chlorination, and several separation methods were investigated. Partial separation of the yttrium and rare-earth element fraction was made by chemical methods and by solvent extraction. Thermal decomposition of aqueous rare-earth nitrates or selective ignition of yttrium and rare-earth oxalates yielded a fraction enriched in cerium. A fraction enriched in the light rare-earth elements resulted from a double sulfate precipitation, whereas a potassium ferrocyanide pr cipitation yielded a fraction enriched in yttrium. Precipitation with dimethyl phosphate yielded a fraction enriched in yttrium and heavy rare-earth elements. Enriched fractions were obtained with several solvent extraction systems. A system consisting of rare-earth nitrates, nitric acid, and tri-n-butylamine-3 methyl-2-butanone favored the separation of yttrium from the heavy as well as from the light rare-earth elements.

Jan 1, 1961

By F. S. Crawford

It has been said that safety promotion passes through four stages--the band-playing, the machine-guarding, the protective equipment, and finally the educational stage; the last is the most important in the development of the safety program. It has been estimated that only 15 percent of accidents can be pre- vented by machine guarding and protective equipment; the other 85 percent must be stopped by the safety efforts of the individual workers and their supervisory officials, and one of the fundamentals of safety work is the education of workers to develop safety consciousness or safety mindedness. One way of educating men to think about safety is by the use of posters. Safety engineers at the Calumet 2 Hecla mines in Michigan have been conduct- ing a safety contest among the men by the use of posters of an unusual type in addition to those usually employed to illustrate bad practices and to display the number of days without a lost-time accident. The first requisite for the success of the safety poster is a good artist or draftsman; in the poster contest instituted at the Calumet & Hecla mines two sheets were prepared illustrating various conditions in the slope workings, including a large number of unsafe practices. The object of the contest was to get the men to think about safety through criticism of the unsafe conditions displayed on the posters. The following notice accom- panied the posters:

Feb 1, 1935

By BUREAU OF MINES

The cheapest method of handling gravel in placer mining operations is by hydraulic mining . In working gravel deposits by hydraulic mining , it is essential that an abundant supply of water under sufficient head can be economically developed and that there is sufficient grade for sluice boxes and for disposal of the tailing . Without dumping facilities , simple hydraulic mining is an impossibility . The cost of hydraulic mining may range from 2 cents a yard under favorable condıtions to 12 or even 20 cents under less favorable conditions and to 35 cents or more a yard in Alaska , according to conditions of operation , and if frozen gravel is encountered . When it is necessary to elevate gravel , the costs may exceed 60 cents a cubic yard . When the natural conditions do not permit of hydraulic pining proper , other methods of elevating the grade are employed , some of which are described below . Bucket dredging has replaced hydraulic mining in importance in California and other states where hydraulic mining was once extensively carried on , and is by far the cheapest method of elevating gravel when mechanical methods are required and the physical conditions are suitable for dredging . Dredging costs vary greatly under the different conditions encountered , and the total amount of gold to be recovered must of course be enough to warrant the cost of a dredge installation . Gold dredging operations in the United States are fully described in Bull . 127 , U.S. Bureau of Mines .

Jan 1, 1922

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By C. E. Augustine, B. A. Landry, P. Nicholls

"Wien bituminous coal is burned in a hand-fired up-draft boiler used for heating purposes it has a decided tendency to produce smoke. A design of furnace and a method of firing and attendance that are satisfactory for fuels low in volatile matter, as anthracite or coke, are not necessarily Satisfactory for bituminous coals. It is therefore becoming common practice to use a special design of furnace for bituminous coals, in order to facilitate the combustion of the volatile matter and soot. This is done by (1) providing a larger combustion space to give more time for the combustion, (2) construction that will produce a better mixing of the gases and secondary air supplied over the fuel bed, or (3) keeping the gases at a higher temperature by preheating the secondary air, as may be done by surrounding them with refractory surfaces, or causing them to pass through a fuel bed of hot coke. A furnace may be built to use any or all of these methods of smoke prevention.In Bureau of Mines Technical Paper 303, Blizard5 and others give tests on a large heating boiler when burning coke, anthracite, and bituminous coal. Certair alternative furnace arrangements were used, but there was no material change in the furnace design for the various fuels. Since that time the manufacturer has made modifications in design to adapt it for use of bituminous coal, and additional tests have been made to determine how this change affected the production of smoke and the efficiency of the boiler."

Jun 1, 1929

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By Henry P. Wheeler

H ELIUM (chemical symbol: He) is a member of a family of normally gaseous elements, which, because of their zero valence and corresponding lack of chemical activity, are called the "noble" or "inert" gases. It is a monatomic element with an atomic number of 2, and it exists naturally in two stable isotopic forms-He3, with an atomic mass of 3.0170, and He4, with an atomic mass of 4.0039. With the exception of a trace (10-6 percent) of He3, all of the naturally occurring helium is He4. Two unstable isotopes-He5, with atomic mass 5.0137, and He6, with atomic mass 6.0208-are listed by various scientists, but the existence of He5 is questioned by some of them. He6 is radioactive, with a half-life of 0.8 second. Helium was discovered in 1868 in the gaseous atmosphere surrounding the sun. Although several scientists studied the solar chromosphere that year, it is generally agreed that J. Norman Lockyer of England should be credited with the discovery of helium, which he named, deriving the word from "helios," the Greek name for the sun. It was not found on earth until March 1895, when William Ramsay of London produced a small amount from a sample of cleveite, a uranium-bearing mineral. In 1905, H. P. Cady and D. F. McFarland of Kansas found helium in natural gas produced from a well near Dexter, Kans., and for the first time a large source of helium became available.

Jan 1, 1952

The Federal Mine Safety and Health Act of 1977* defines respirable dust as dust measured with a device approved by the Secretary of Labor and the Secretary of Health and Human Services [30 USC 842(e)]. The approved sampler for respirable coal mine dust is the coal mine dust personal sampler unit (CPSU) [30 CFR 74; Jacobson 1971; Jacobson and Lamonica 1969]. The CPSU is generally called the 10-mm nylon cyclone, although the 10-mm nylon cyclone is actually just one component of the CPSU. The CPSU may either be mounted on a worker (with the sampling head positioned in the breathing zone for personal exposure monitoring) or in a fixed location for area sampling [Tomb 1990]. The CPSU consists of a pump unit, a sampling head assembly, and a battery charger if rechargeable batteries are used in the pump unit [30 CFR 74.2]. The sampling head assembly contains two stages. The first stage is a 10-mm nylon cyclone, which has collection characteristics similar to an elutriator. The amount of dust penetration depends on the flow rate [Jacobson and Lamonica 1969]. The second stage is a membrane filter (vinyl, pore size 5 pm) that collects the dust passing through the cyclone. The dust collected on the membrane filter is weighed to a precision (standard deviation) of 81 pg [Parobeck et al. 1981], and the respirable dust concentration in the mine atmosphere is then determined from the mass of dust collected and the volume of air sampled [Tomb 1990].

Jan 1, 1997

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Robert M. Baker

This document details the method whereby Allen Corporation of America gathered and analyzed data and developed an annotated bibliography of metal and nonmetal mine fire reports (1950-1979). The primary objective of this program was to develop the annotated bibliography which included MSHA accident reports and periodicals. Two additional objectives were to gather data on non-reportable fires and to conduct statistical analyses on the data to delineate trends. Data was acquired from three major areas: periodicals, MSHA fire reports, and mine safety directors. Data was separated into reportable fires (at least ½ - hour duration or injury), non-reportable fires, and opinion data. The data was then analyzed by time trends, state, ore, ignition source, burning substance, location, equipment, detection, duration, injuries, fatalities, and successful extinguishing agent. The authors make a number of recommendations: (1) improved stationary electrical equipment design and fire protection, (2) improved design of mobile equipment to separate combustibles from ignition sources, (3) improved maintenance, (4) improved housekeeping, and (5) improved training. The document is divided into two volumes and an appendix. Volume I contains data acquisition procedures, data analysis procedures, and conclusions and recommendations. Volume II contains a chronological list of mine fires and fifteen indexes to assist the reader in locating fire incident report of interest. The Appendix contains the annotated bibliography of over 300 metal and nonmetal mine fire reports and journal articles and a list of non-reportable fires.

Jan 1, 1980

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

By Michael D. Balen

The U.S. Bureau of Mines (Bureau) is currently conducting a four-year study to assess the mineral resources and the mineral development potential of the 5.7 million acre Valdez Creek Mining District (VCMD) located in southcentral Alaska. The VCMD study is part of the Bureau's ongoing statewide mining district evaluation program. This report is a summary of the 1988 field work. The field work involved collection of reconnaissance placer and rock samples, and also involved sampling and examination of the mines, prospects, and mineral occurrences which were identified by literature research of the geology, exploration history, and mining history of the district. During the 1988 field season, Bureau personnel spent a total of 11 weeks in the field, collected 1,006 rock and placer samples, and located, mapped, and sampled 106 of the known mineral occurrences. The Bureau has visited 243 of the 250 known mineral occurrences during the course of the VCMD project. Reconnaissance sampling for placer occurrences resulted in the identification of 4 previously unreported gold placer occurrences, and identification of 5 occurrences that contain detectable levels of platinum or palladium. Reconnaissance sampling for lode sources of base and precious metals resulted in the identification of 5 new Lode gold-silver occurrences, identification of 2 occurrences that contain elevated quantities of chromium, cobalt, nickel, palladium, and platinum, and identification of one occurrence that contains elevated quantities of copper, molybdenum, anti zinc.

Jan 1, 2011

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971