Search Documents

1. Mine drainage constitutes surface or ground water which flows from mines or mine sites and is usually characterized by concentrations of acidity or alkalinity. 2. The regional geology controlling the ground water flow pattern in conjunction with the life cycle mining plan can serve as a basis for making decisions about quality of water that can be expected to be encountered. 3. In regard to the prevention and control of acid water formation in underground coal mines, much is left undone in research and education: (A) Very little literature is available on this specific subject although much has been written on water management in underground mines. (B) Little or nothing is contained in the text books and curricula used in mining departments at colleges and universities with the result that educational offerings may be seriously deficient in these areas. 4. Prohibiting water entry into underground coal mines is the best method of preventing water pollution. Since this is not possible as mining operations are extended, preventing water or oxygen from contacting acid producing material may offer the next best alternative. 5. More emphasis is needed during the mine planning stage on steps to prevent water pollution. Such life cycle considerations as type of mining, sequence of development and spatial configuration as well as the elements of the drainage network and final network organization and extent must be considered.

Jan 1, 1970

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressures. New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 2010

By D. S. Harper, C. O. Carman

A German coal planer was put in operation in the Keystone mine of the Eastern Associated Coal Corp. , Keystone , W. Va . , in August 1960 . At present , the planer is mining in the fourth panel . The blocks of coal mined were 340 by 1,900 feet in panel 1 , 340 by 1,660 feet in panel 2 , 590 by 1,900 feet in panel 3 , and panel 4 , currently being mined , is 590 by 1,900 feet . Almost one- half million tons of coal have been mined from these four panels . An 11 - man crew handles the complete planer operation and produces an average of 500 tons of clean coal per shift . Self - advancing hydraulic props are used to support the roof over the entire face . Roof control and action on all of the panels has been highly satisfactory . During periods of extreme pressure , some additional support is required in the tail entry where evidence of weight from the retreating longwall extends about 200 feet outby the face . The time lost from production by moving equipment between panels has been reduced steadily . The move from panel 3 to panel 4 required 5 days , but it is believed that even that time could be reduced .

Jan 1, 1963

Coal-bearing beds underlie 23,000 square miles, about one third of Missouri's total area. Twelve out of more than twenty named coal seams have been or are being commercially mined. The remainder are too thin for commercial production. The coal is high volatile bituminous, with reserves estimated to be six billion tons, 1.24percent of U.S. coal reserves. Coal-bearing strata are generally thin seams which can be up to five feet thick. Typically, mined seams are about 28 inches thick. Coal deposits were first mined in Missouri in the 1840s, with the coal used primarily for domestic heating and blacksmithing. Production increased with the introduction of steamboats on the Mississippi. Coal production in 19 17 was six million tons. Production has steadily declined from a high of nearly seven million tons in 1984 to 2.3 million tons in 1991. Declining production is the result of several factors, including competition from other energy sources and the high sulfur content of Missouri coal. Today, coal-fired electric generating plants are the biggest consumers of Missouri coal. The Missouri regulatory program was conditionally approved November 21,1980, and fully approved January 17,1983. Its Abandoned Mine Land program was approved January 29, 1982.

Jan 1, 1992

By Richard A. Thomas, Isaac A. Zlochower, Gregory M. Green, Kenneth L. Cashdollar, Martin Hertzberg

This paper reports the results of flammability studies for methane, propane. hydrogen, and deuterium gases in air conducted by the Pittsburgh Research Laboratory. Knowledge of the explosion hazards of these gases is important to the coal mining industry and to other industries that produce or use flammable gases. The experimental research was conducted in 20 L and 120 L closed explosion chambers under both quiescent and turbulent conditions, using both electric spark and pyrotechnic ignition sources. The data reported here generally confirm the data of previous investigators, but they are more comprehensive than those reported previously. The results illustrate the complications associated with buoyancy, turbulence, selective diffusion, and ignitor strength versus chamber size. Although the lower flammable limits (LFLs) are well defined for methane (CH,) and Propane (CA), the LFLs for hydrogen (HZ) and its heavier isotope deuterium (D2) are much more dependent on the limit criterion chosen. A similar behavior is observed for the upper flammable limit of propane. The data presented include lower and upper flammable limits, maximum pressures, and maximum rates of pressure rise. The rates of pressure rise, even when normalized by the cube root of the chamber volume (V 1/3), are shown to be sensitive to chamber size.

The coal deposits in Alaska occur in several major coal fields or basins. The deposits underlie about a quarter of the state, an area larger than Montana. Approximately 60 percent of the coal is bituminous and 40 percent is subbituminous. Less than one percent is lignite or anthracite. Although known coal reserves are estimated at only 6.1 billion tons (about 1.25 percent of U.S. reserves), estimates place the hypothetical reserves at 5.5 trillion tons and the identified reserves at 170 billion tons. The differences are due to limited exploration programs within the state. Conditions affecting mining and reclamation are unique to Alaska because of its extreme northern latitude. For example, permafrost occurs in about 75 percent of the state; tundra vegetation occupies vast treeless regions; and the climate is characterized by extremely cold winter weather and a short summer season. In addition, hydrologic conditions are considerably different from those in other states; major streams fed by silt-laden glacial melt water contain greater concentrations of natural sediment than the effluent discharge limits permitted by federal regulations. Also, some coal field locations are subject to potentially high seismic risk. These factors make coal mining and reclamation in Alaska more difficult than in other states. Alaska's program to regulate surface coal mining was approved May 2,1983. The Abandoned Mine Lands program was approved December 23,1983.

Jan 1, 1992

By J. W. Paul

A superintendent is one who has the oversight and charge of some organiza- tion or enterprise, with porer of direction. The superintendent of a coal mine is the official who is in general charge of conducting the operation of the nine for the purpose of producing coal; he is accountable to his superiors for all matters that relate to the cost of production and safety in operation, ed under him are all the underground officials and other personnel making up the mine organization. The responsibility of the superintendent covers all the principal phases of mining, purchases of materials, issuance of supplies, accounting, and upkeep of the property and equipriont. In a broad sense, the superintendent must view his job as embraced under four gneral heads: (1) Construction, (2) instruction, (3) supervision; and (4) discipline. The degree of efficiency with which each of these phases of his work is conducted is a measure of the safety factor which the superintendent injects into his job. Injury to workmen and damage to property may be due to neglect of one of these general headings; as for example in the collapse of a scaffold there has been faulty construction which may be found upon investigation to have been the result of faulty instruction or lack of instruction. It may be that the condition of the scaffold was not ascertained in advance of its collapse through faulty supervision, or the discipline of the workmen had been neglected.

Sep 1, 1930

By D. Harrington, M. W. Von Bernewitz

"The erection of barricades by men who are shut off from escape in mines at time of fire or after an explosion has been consistently advocated by the United States Bureau of Mines. Largely through the publicity given by the bureau to this excellent type of emergency safety endeavor, several hundred lives have been saved during the past 20 years. One of the earliest instances of barricading in the United States of which there is fairly complete record was in connection with the Cherry mine fire in Illinois in 1909; in this fire 259 lives were lost, but 20 men were saved by two barricades and were brought safely to the surface after seven days. In another coal-mine fire, followed later. on by an explosion, at Delagua, Colo., in 1910, 79 lives were lost, but 18 men saved themselves by erecting canvas brattices or barricades; the miners in one barricade were removed safely after five hours and those in another after 21 hours. In 1911, after an explosion in a coal mine at Briceville, Tenn., in which 84 lives were lost, five persons were brought out alive after 58 hours behind a barricade. Twenty hours after an explosion in which 73 were killed at McCurtain, Okla., in 1912, 13 men were taken out alive and one dead from behind a barricade or partition constructed of canvas. In 1914, after an explosion at Eccles, W. Va., in which 181 were killed, 35 men barricaded themselves in one place and after four hours were brought to the surface alive; this barricade was also of canvas. In 1915, 112 men were killed in an explosion at Layland, W. Va., but two groups of men, 47 in all, were able to barricade themselves; after four days 46 men were rescued alive, but one man was dead. In 1915, an explosion at Boomer, W. Va., killed 23, but 27 others barricaded themselves in one place and after seven hours came out alive. All of the foregoing instances of barricading were in coal mines. In 1917 there were three cases of barricading in a Montana metal-mine fire (the North Butte) during which 163 lives were lost. One of the barricades, sheltering 19 men, failed because the region barricaded was in porous broken ground through which the poisonous gases seeped and killed the entire group. From another of the barricades, engineered by an assistant foreman, 8 men were taken out, 6 uncon¬scious and 2 dead, 50 hours after the fire started. The 6 unconscious men lived, out the assistant foreman who directed the men was one of the 2 who had died. In the third case of barricading in this metal-mine fire,,men, also led by an assistant foreman, kept themselves closed in for about b6 hours and then broke barricade or bulkhead, 25 oing in one direction to safety, and 4, including the assistant foreman, going in another direction to death from poisonous gases. There have been a number of other cases of barricading, some successful and others a failure. Probably the worst failure was that in the argonaut (gold) mine fire in California in 1922; all of a group of 46 miners behind a barricade were found dead when reached after 21 days."

Apr 1, 1933

By H. B. Humphrey, F. E. Cash

The following information on accidents in Alabama during 1930 was compiled from data obtained from the companies represented in a course on accident prevention given by the United States Bureau of Mines in Birmingham. These mines produced nearly three-quarters of the tonnage of that State for the year, and included most of the larger operations in the district. The figures are probably representative of the mines which are doing recognized safety work, and are better than the average for all the mines in Alabama. Table 1 lists the days lost in accordance with the weights given to fatalities and permanent disabilities, part and total, which is the scale used in the National Safety Com¬ petition for Mines, conducted by this bureau. By way of explanation, temporary disabilities are weighted according to actual number of calendar days of disability, including Sundays and holidays — that is, all days are counted except the day of accident and day of employee's ability to return to duty. Hernia is classed as a temporary disability to be charged with the actual number of calendar days during which the employee was unable to work. Table 2 gives the number of accidents and the days lost from each cause at 45 coal mines and 7 iron ore mines, also the average frequency and severity rates.

Aug 1, 1931

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By Robert H. Essenhigh

A stirred reactor (SR) combustion system has been developed to gather information on the mechanisms of ignition and flame propagation of coal dust under conditions similar to those found in coal dust explosion flames. The prime scaling variable considered in this study is that of rapid particle heating (between 105 and 106°K/sec) which is accomplished by means of turbulent mixing during combustion. The SR combustors tested in this study have consisted basically of spheres hollowed in the centers of refractory housings. Coal and air mixtures have been injected into the spherical combustion chambers through a single jet, two opposed jets or four opposed jets. The diameters of the jets have ranged from 0.63 to 0.22 cm. The volumes of the combustion chambers have ranged from 1.0 to 0.2 liters. The reactors have been equipped with thermocouples embedded in the combustion chamber wall as well as a thermocouple located in the exhaust gas stream. In the latter versions of the SR, provisions were made for both solid sampling and gas sampling of the reactant stream exiting from the combustion chamber. Experiments have been carried out using pulverized bituminous coal. The coal has been reacted in an SR in mixtures of air and air/nitrogen. These experiments have provided information on the mode of ignition of the coal as well as yielding information on the kinetics of coal pyrolysis through the use of SR theory. Ash tests performed on the reacted samples collected from the SR indicated that the majority of the values of weight loss percentage were between 60 and 70 percent. The percentages of weight loss were relatively unaffected by changes in temperature which varied between 1100 and 1700°K and by changes in residence time which varied between 10 and 20 millisec. Volatile matter tests performed on the samples indicated that the volatile matter left in the char ranged from 3 to 20 percent of the original content. By assuming that all the mass loss was due solely to pyrolysis with no combustion occurring at the particle surface, Q-factors for each test have been calculated. The results of these calculations indicate an average value of Q equal to 1.88. This finding shows that the majority of mass loss can be attributed to pyrolysis. The fact that the extent of reaction varies only slightly over the range of test conditions has been examined in the context of the two component hypothesis of coal constitution. This approach leads to the conclusion that the reaction of the "easily evolved" component VMI is extremely rapid and that the majority of it is removed from the coal in times less than the residence time in the system. This means that the volatile residue remaining in the char can be considered to consist of component II, VMII. If the mass fraction of VMI = 0, then an activation energy of 18.0 kcal is obtained for the pyrolysis reaction. If the mass fraction is assumed to be 0.75, the activation energy increases to 31.2 kcal.

Jan 1, 1978

By R. A. Cattell

The Bureau of Mines actively conducted a well-coordinated research pro- gram during the past fiscal year on problems dealing with the production of oil and gas, transportation of natural gas, chemistry and refining of petrole- um, thermodynamic properties of hydrocarbons, and the processing and utiliza- tion of incombustible helium gas. These particular reserach phases, compris- ing the presently scheduled activities, are integral parts of a broad program selected soon after the war as suitable for Bureau of Mines study, to meet immediate needs for specific information on petroleum and natural-gas problems of national scope. Important progress was made and many technical reports were finished during the year. Several reports were published on gas-condensate production problems, one giving the results of laboratory tests of relative merits of various steels and alloys for rosisting the corrosion that occurs in high-pressure gas- condensate wells. Research was continued, using the Bureau's windowed cell, to determine the characteristics of gas-condensate fluids, and an important paper on the phase relations of these fluids at low temperatures was published. An important part of the Bureau of Mines petroleum production research program for many yoars has been the engineering study of type oil fields. This year reports waro completed on the Lake Creek, Sheridan, and West Rod River fields, Tex.; the Atlanta field, Ark.; and the Bogge field, W.V. Othor fields under study and for which reports will be issued are the Carthage and Now Hope fields, Tex., and the Weber pool, Okla. Spocial studios to determine the characteristics of the oil-gas solutions as they exist within the native reservoir rocks have been in progress in the North Lindsay field, Okla.; the Elk Basin field, Wyo. and Mont.; and the Rangely field, Colo. The North Lindsay study brought to light several un- usual physical proporties of the oil as it is found in this deep-seated reservoir. For instance, its viscosity is less than that of water, and more than 2 barrels of the initial reservoir oil must be produced to yield 1 barrel of "stock-tank oil." In the Elk Basin and Rangoly fields the oil-gas solution varies in composition within the reservoir, depending upon structural location. Engineering studies were continued on woll spacing and on drilling fluids with special emphasis on obtaining uncontaminated cores, or coros for which the flushing action of the drilling fluid can be dotormined accurately. In connection with research on production of oil by secondary recovery methods, progress was made in studies of conditioning water for subsurface injoction, of input ratos and pressures for water-flooding oil sands, and of the selective plugging the more permeable mediurs to prevent or retard channel- ing of the injected fluid. The availability of fuels for all types of internal-combustion engines still is tho primary resoarch project in potroleum chomistry and refining. This rosearch program is subdivided into a sorios of problems under four main topics: (1) Raw-material studios; (2) relationships of fuel consumption, proporties, and performanco; (3) utilization of potroleum products; and (4) analytical mothods, which include chomical and physical property detorminations.

Dec 1, 1949

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960

Ohio has an estimated 46 billion tons of coal beneath 12,000 square miles of the eastern third of the state. Recoverable coal reserves within this vast area are estimated at 21 billion tons, 3.2 billion tons of which have been mined since 1800. Ohio is the eleventh-largest coal- producing state in the nation and ranks third nationally in coal consumption. Coal resources in Ohio lie in as many as 60 identifiable coal seams along the northwestern flank of the Appalachian coal basin. Except where interrupted by minor faults and erosional discontinuities, these rocks dip gently and uniformly to the east, simplifying the mining methods needed to extract the coal. Fourteen of Ohio's 60 coal seams are considered to be important, although only a small number of seams are currently being mined. Ohio first enacted a surface coal mining law in 1948, requiring in part a $100 per acre reclamation bond. Ohio progressively strengthened its surface mining law in 1949, 1955, 1959, 1961, 1965,1972,1975,1978, and 1981. At the time of its enactment, Ohio's 1972 mining law was one of the most stringent in the country. This law also created a state coal severance tax of four cents per ton to be used for abandoned mine land reclamation. Ohio received primacy to regulate the surface coal mining operations within the state August 16,1982. Its Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By E. C. Lane

["_&apos;_-is is t`-e tenth in a series of retorts on proferties of cornmerci-al motor fuels, m,-_de in accord^nce ::ith a cooper: tine aSreement between the Cooperative Fuel scorch (C.F.R.) Committo e ^nd the. PPure__u of Mines of the United_ States De_nartr.ent of the Interior. Zee first report rave data. on motor gs.solir_es sold. during .e winter of 19,-"1-3b. e are ent report presents an^..lytico1 data f&apos;i&apos;r samples, rerrerentin_E, t:-.e products of apyroximately 90 conr.anies, hich, as in previous surveys, include both lame and stall surnliers. In ?_"dition, the Pacific coast is represented by data that were avera,;el ty the Pacific Coast Technical Group before bein submitted and are rublisi,ed exectly zis they were received. As in previous s?nrve,rs, the data r~Lre divided into the three groups of samples of regular-price, premiu::--trice, and third-grade gasolires, and each group has been averaged sel c~r~.tely. he number of nmtles, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as folio:;s: Reg<.~-lar price, 934 ca.^rnles, 2c0 i to s, and ~0 brands; premium price, 460 saris les, lPitems, an&apos;. -C` brat&apos; i _~ t__ rd grade gaseline, 360 samples, 177 i te.^..s, and of these terms as _ised in the surveys are a:: follows:]

Jan 1, 1941

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963