Search Documents

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By Edwin A. Clarke

[For almost 2 decades the Bureau of Mines has been Interested in converting solid fuels to liquid fuels. Small-scale laboratory investigations were carried on for a number of years.4/ This work wad expanded substantially under authority of Public Law 290, approved by the 78th Congress on May 5, 1945. As part of the. broadened program, coal-hydrogenation demonstration plant was designed and erected at Louisiana, Mo., where: hydrogen-manufacturing and compression equipment, shoes, electric power, and other utilities and facilities were available from a discontinued wartime ammonia works . The plant uses the direct -hydrogenation or Bergius process, but the process differs from prewar European practices in many respects. Many noteworthy improvements h eve bean made, particularly by substituting automatic instruments for manual control of process variable's, in line with modern American processing practices. The over-all objective of the demonstration plant is to bridge the gap between laboratory end commercial-scale operation by furnishing cost and engineering data to develop a synthetic liquid-fuels industry when it proves technically and economically justified. Fitting into the over-all program, specific objectives o early runs were to (1) train personnel who had no experience with this type of operation, (2) break in the installed equipment, (3) obtain successfully integrated operation of the entire plant, and (4) work towards obtaining data on the hydrogenation of coal-tar oil and a typical low-ash coal. In beginning fan integrated operation, it is common practice to operate and obtain reaonably smooth performance of each unit before the over-all operation is undertaken. The first part of the plant completed was the refinery, consisting of several fractionating systems, a stabilizer, and a chemical treater.]

Jan 1, 1953

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical studies have been prepared for the US Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which we may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to- noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna con- figurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National Bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by NBS. The recent NBS data is that used by Collins in the final predictions. The following outline indicates the order and subject matter treated in the subsequent sections: Section 2 - Signal-to-Noise Analysis for Loop-to-Loop Mine Communications Section 3 - The Horizontal Electric Dipole Section 4 - Signal-to-Noise Analysis for Down-Link Line Source Mine Communications Section 5 - LF Communication Section 6 - The Application of Recent NBS Noise Data to Mine Communications Section 7 - Analysis of Mine Communication Propagation Programs

Nov 15, 1974

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By D. Bienstock, R. C. Kurtzrock, E. R. Bauer, J. H. Field

To remove hydrocarbons and carbon monoxide in automotive exhaust by oxidation , a catalyst of 4.2 percent Uз Og , 1.7 percent Cr₂ 0 , and 1.7 percent CuO supported on 1 /8 - inch y- alumina spheres was tested in a reactor in place of the muffler of a 1 / 2 - ton truck . Tests were made with both nonleaded and leaded gasolines . With the engine at operating temperature , tests were made with the engine idling and with the vehicle cruising at 30 mph . Auxiliary air was added to maintain an oxygen concentration of 3 to 4 percent in the gas leaving the catalytic reactor . The vehicle was operated for 83 hours (about 60 percent of the time with the engine idling ) and 525 miles with nonleaded gasoline . Conversions of 98 percent of the hydrocarbons and 100 percent of the carbon monoxide were achieved with the engine idling and with 7,000 ppm carbon atoms and 4- percent carbon monoxide in the feed to the reactor . Hydrocarbon conversions of 75 percent were obtained at cruising speeds of 30 mph with a feed of 1,700 ppm carbon atoms ; the carbon monoxide concentration was less than 0.3 percent in the feed and was unchanged in passage through the reactor . Identical activity was obtained initially in switching to a gasoline containing 1.9 ml tetraethyl lead (TEL) per gallon . However, there was a gradual loss in activity thereafter . Conversions in tests with the engine idling about 50 percent of the time , had decreased by 23 percent for the hydrocarbons and by 25 percent for the carbon monoxide from their initial values after 122 hours and 1,300 miles of operation with leaded gasoline . The levels of radioactive materials in the exhaust of the reactor and the radiation in the vehicle were negligible .

Jan 1, 1963

1. In 2002, a total of 763 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Examples of nonmetal mining operations include the mining of clay, trona, barite, phosphate rock, gypsum, talc, gemstones, and pumice. Nonmetal mines comprised 5.3% of all mining operations. • Nonmetal mining operations are located in all but nine states or territories (Alaska, Delaware, Maine, New Hampshire, Rhode Island, Vermont, Wisconsin, Puerto Rico, and the Virgin Islands). • Mines producing common clay comprised 29.2% (n = 223) of all nonmetal mining operations.

Jan 1, 2004

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 1 and 2 provide a summary view of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1990 and 1991. Table 3 shows the relative importance of a selected group of minerals produced in Latin America in the world mineral economy.

Jan 1, 1993

By Judith A. Eisele

The possibility of improving the volatilization of gold through the formation of a metal-gold chloride vapor complex was investigated. Gold-silica mixtures, containing ferrous and nonferrous minerals and salts as additives, were treated in a laboratory tube furnace with a flow of chlorine gas at various temperatures. The addition of pyrite (FeS2) to a charge of gold-silica increased the volatility of the gold from 3, 20, and 62 percent of the total gold to 62, 93, and 100 percent at 200°, 300°, and 400° C, respectively. Chemical analyses of the condensate indicated the volatile species to be FeAuCl6.

Jan 1, 1971

By L. B. Pankratz

The Bureau of Mines conducted heat-content measurements above 298.15° K for dehydrated analcite (NaAISi2O6) to 1,000°K, kaliophilite (KA1Si04) to 1,800° K, and leucite (KAlSi206) to 1,800° K. Heat content and entropy increments were tabulated, and the heat content data, were given in equation form. A first order transition was noted for kaliophilite near 810° K with a heat absorption of 160 cal/mole. Leucite had a second order transition which became complete near 955° K. In this transition a crystal change occurred from tetragonal (low-temperature form) to cubic (high-temperature form).

Jan 1, 1968

By David S. Yantek

Miners in underground coal mines experience prolonged exposure to high noise levels, often with A-weighted sound levels in excess of 90 dB. Field tests have shown that the continuous miner conveyor is a dominant noise source. This paper will identify the most significant noise-radiating surfaces on the continuous miner tail section using vibration levels and surface areas to estimate the sound power levels of each surface. In addition, using five test cases, this study will examine the effects of three engineering noise controls on the surface-averaged vibration levels and average sound levels measured with four microphones located two meters from the tail section. The noise-radiating surfaces of the conveyor’s tail section include the top and bottom decks, the sideboards, and the flex plates. Emphasis is placed on the changes in the estimated sound power levels in the 500 – 2500 Hz 1/3-octave bands since this frequency range accounts for 80-85% of the sound energy near the tail section. The results show that the bottom deck is the most significant noise radiator for the untreated miner. Installing a coated bottom deck reduces the estimated sound power level radiated from the bottom deck by 11 dB and the average sound level by 2 dB. Using a coated tail roller results in reductions of the estimated sound power levels for individual components from 1 to 4 dBand reduces the average sound level by 2 dB. Coating the slide plate has little effect on both the estimated radiated sound power levels and the average sound level. The test results indicate that modifications that reduce flex plate vibration and reduce energy transfer from the tail roller into the tail section will be effective in reducing noise when combined with a coated tail roller and coated return deck.

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006