Search Documents

By Mohamad Hussein

Low strain dynamic tests are performed to evaluate the structural integrity of driven or cast-in-place concrete piles. This type of testing requires minimal pile preparation, and is simply performed by attaching an accelerometer to the pile head and striking the pile head with a hand held hammer. The measured data is processed by a dedicated system, inspected for wave reflections, and interpreted based on one dimensional wave propagation theory. Piles are normally tested shortly after installation so that problems can be identified early and corrective measures taken before construction of the superstructure. However, evaluation of existing foundations is occasionally required. Often, pile installation records are not available rendering impossible any rational foundation reanalysis. This paper discusses three case histories where low strain dynamic measurements allowed determination of pile lengths and structural integrity under existing structures where pile heads were not accessible.

Jan 1, 1992

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By Van E. Komurka

This paper presents a cost comparison of the driven pile foundations for two large Wisconsin Department of Transportation (?WisDOT?) projects in Milwaukee, Wisconsin: the Marquette Interchange South Leg, and the Canal Street Viaduct. The projects? geology is fairly similar, but their methods/approaches to pile foundation design and installation differ. Although the Marquette Interchange South Leg had deeper poor soils, its pile design was more-cost-effective than the Canal Street Viaduct?s. Potential reasons for cost differences between the projects are identified, and the effect of the different design and construction approaches on economics is discussed.

Jan 1, 2009

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By Thoedtida Thipparat

The diaphragm walls and barrettes are very important to the constructions of multi-storeyed buildings, elevated expressways, subway railway stations, etc. Uncertainties particularly increase in accordance with the construction progress. Overcoming uncertainties influences the construction goals including achievement of time. This paper is aimed at proposing an uncertainty assessment and delay evaluation model to assess uncertainties and evaluate delay resulting from those uncertainties. Neurofuzzy systems (NFSs) for assessing uncertainties and evaluating delays are developed. Artificial neural networks (ANNs) have ability for learning from the past data and generalizing outputs for the next applications which are provided for fuzzy logic systems (FLSs). FLSs have ability for exploiting the tolerance of imprecision and uncertainty. FLSs provide the reasoning to the ANNs. Uncertainties affecting each operation were assessed and delays were evaluated by following steps of the proposed model. The uncertainty assessment and delay evaluation approach was applied to a diaphragm wall and barrette construction to demonstrate how to implement the proposed model. The results of the test case application were used for handling delay at all operations regarding the corresponding uncertainties.

Jan 1, 2006

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987

By J. Matos e Silva

The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the Eurocode 7 recommendations. A comparison is also made with the behaviour of the diaphragm walls during the construction phase. From the referred examples the author presents his conclusions.

Jan 1, 2002

By Bernard H. Hertlein

Transportation system structures have come under very close scrutiny in the last couple of years, largely due to the damaging effects of disasters, both natural and man-made. In the Pacific northwest and California, earthquake risk is a major concern. In the central and eastern states barge impacts on bridge piers and docks are a big worry. In all cases of bridges over water and waterside structures, scour is a primary concern. Some of the results of this scrutiny have been changes in design and construction methods, and the introduction of more testing to supplement field inspection during construction, and throughout the service life of the structure. Future construction of bridges and docks will almost certainly see a continuing growth in these practices. Where foundations are concerned, particularly for bridges and waterside structures, many state and local authorities have started specifying drilled shafts rather than driven piles. Where the shafts must be constructed under water or slurry, visual inspection of most of the work is impossible, and one of several different Nondestructive Tests (NDT) is often specified. Contractors' experiences with these methods have varied considerably, and there is a great deal of controversy in the deep foundation industry over the reliability of NDT methods for assessing the integrity of foundation shafts or piles. The author has had more than 15 years of practice with the various NDT methods for deep foundations, on projects all over the US, particularly foundations for bridges and dock structures, and has developed an understanding of the "NDT controversy" as it has become known. In particular, experiences in the Pacific Northwest, California, and Alabama have illustrated the reasons for the controversy. This paper reviews these experiences, and suggests some steps that owners and contractors can take to reduce the risk of inconclusive or downright inaccurate test results.

Jan 1, 1998

By Louis Donolo

New buildings in today's urban environment, especially in down-town areas, invariably involve the construction of multiple level basements. Used for parking, storage and commercial space, these underground structures normally extend 30 to 50' and more below grade and, to make optimum use of expensive land, they usually occupy the full site right up to street/sidewalk and property lines. SOIL SUPPORT SOLUTIONS Building these basements requires vertical excavation, and consequently, a temporary soil support system which will eventually be replaced by the permanent foundation walls of the structure.

Jan 1, 1987

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017