Search Documents

By Henk E. Brassinga

In Rotterdam a number of underground parking facilities have been built and are under development in the inner city, and in the suburbs. These parking facilities are located at already densely built areas. The design of these constructions has to take into account the impact of the building activities and that of the final construction on the surroundings. In this paper some examples of the different building methods of newly realized underground parking facilities are described, and problems that occurred during the construction are pointed out. In the soil conditions as present in Rotterdam the cost effectiveness of underground facilities can be improved by deepening the parking facility, and at the same time reducing the surface area so that the total parking volume remains constant. In this way the total volume of the diaphragm walls and the costs of the project is reduced.

Jan 1, 2006

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2005

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By G. Noce

The ever more present necessity for greater precision in foundation structures on vertical piles subject to horizontal forces applied to the heads, in the light of of the latest knowledge about the elastic-plastic behaviour of the soil has led to the use of numerical calculation for the formulation of a general resolution method for the problem. The calculation method that will be set out, applicable to piles with inertia moments variable discreetly along their axes is especially useful when studying steel structures for medium and large tonnage vessels for which the metal piles are often constructed for the assembly of section of equal external diameter but different thickness and therefore different inertia moments. Two examples are given of constructions whose foundations have been projected with these calculation tools, one in the railway sector (foundation pile for the river Nera viaduct - Italy) important for the limitation of horizontal relative deck displacement, the other maritime (Dolphins of the petroleum pier of the port of Bandar Abbas - Iran).

Jan 1, 1989

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By P. Ventura

Reliability of the liquefaction analysis is based on data plotted as by piezocone, as by deep vibrocompactation monitored tests. The negative porewater pressure, re lated to hydrostatic value, recorded by piezocone, is a good marker of the absen ce of the liquefaction. Systematic measures of the ground settlements, inside the vibroinfixed steel pipe, allow to locate the liquefable strata with loose density. Experimental study of the combined soil improvement by stone columns is carry out in particular in sea bed. The interaxis of the columns for the best efficiency is valued as of the vibrocompactation, as of the drainage effects, especially during earthquake.

Jan 1, 1989

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By M. Dondelinger

This paper presents a comprehensive review of steel sheet piling including internationally manufactured hot rolled sections, their history, applications, installation and driving techniques. The discussion will cover both temporary and permanent installations; temporary piling used in construction of cofferdams with various bracing systems, deep foundation installations for buildings, bridges and tunnels, etc., and permanent piling used for highway, railroad and bridge construction as well as for riverbanks, piers, wharfs and docks, normally required for port facilities. In addition, cofferdams, as self-supporting gravity structures where interlock strength is of prime importance, will be discussed. The design and application of light, intermediate and heavy sections will be presented including heavy combined walls and information on Z-shaped, U-shaped and HZ sections and their corresponding interlocks. Emphasis is placed on new developments for design applications for deep foundations and waterfront structures within the "state of the art".

Jan 1, 2010

By R. G. Horvath

In the Hamilton area, and in many other areas of Ontario and around the world, large diameter drilled pier (caisson) foundations are frequently selected as the most appropriate foundation system for heavily loaded structures. Locally, these drilled piers are typically founded in competent glacial till or in the underlying shale bedrock depending on the anticipated design loads. Drilled pier foundations socketed into shale bedrock were selected for the Hamilton General Hospital Addition. The structural loads applied to socketed pier foundations are supported through shaft resistance, which is the shearing resistance developed along the vertical pier-rock interface, and by end-bearing resistance. The factors which control the load-displacement-time behaviour of socketed pier foundations are the strength and deformation characteristics of: a) the concrete pier, b) the rock mass, and c) the interface between the concrete pier and the rock.

Jan 1, 1987

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998