Search Documents

By Kyle Murphy, John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closedloop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermomechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermomechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

Jan 1, 2017

By George Burke

"Many soil mixing methods have evolved over the years, but the Trench Cutting Re-mixing Deep method (TRD) was developed in Japan, circa 1993, to construct continuous uniform cutoff walls, without the need for an open trench. TRD mixing has been used on over 300 projects in Japan for excavation support, groundwater barriers, liquefaction mitigation, soil improvement and pollution containment. To date, TRD mixing has been used on only three projects in the United States: a test cell in Long Beach, Calif., for seawater intrusion barrier in 2004; a groundwater barrier at a wastewater treatment plant in Lincoln, Calif., in 2005; and presently at Herbert Hoover Dike surrounding Lake Okeechobee in southeastern Florida.The most notable benefits of TRD are its abilities to overcome difficult geology, such as layered rock and dense cobbles and gravels that hinder other soil mixing methods, and to create extremely high-quality walls. The method is ideal for situations in which access precludes the use of more traditional methods due to spoil control, such as waterways and congested urban environments or subsurface obstruction/difficult ground. Spoil disposal is minimized since TRD mixes the soil in place.TRD mixing has a horizontal continuity advantage over traditional multi-auger deep soil mixing (DSM) systems. Because DSM systems create walls by overlapping soil-cement columns, the auger may be deflected by difficult ground, and gaps are possible. Gaps may also occur when constructing an exceptionally deep wall due to the possibility of auger deviation from its required vertical alignment.The method also has a homogeneity advantage in layered soils. Because DSM constructs columns by rotating the defined length mixing tools up and down the soil profile while injecting binder, strength and permeability in each layer will vary. The TRD method vertically mixes the entire profile and core samples show highly uniform strength. It is most cost-effective in deep difficult ground such as layered rock or dense cobbles and gravels."

Jan 1, 2009

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By Christian L. Escalera

Over seven years ago, on October 29, 2012, Superstorm Sandy pummeled the Northeast of the United States inflicting heavy damage on New York City Transit’s (NYCT) system. Since then, NYCT has been methodically rehabilitating and hardening its assets to upgrade service and prevent future impacts caused by similar devasting storm surges. Part of these resiliency efforts, NYCT’s 207th St Yard Project is one of many projects that make up the Sandy Repair and Flood Mitigation Program. The work to be performed on the 207th Street Project includes building a perimeter Floodwall along the Harlem River, extending up 215th Street and 9th Avenue with the intent of having the ability to withstand a 500 Year Storm flooding event. The original 1,535 lineal feet of the marine side floodwall design consisted of 937 each W40x235 H-Piles continuously welded to PS 27.5 flat sheet to form an interlocked and composite steel seawall that would protect the NYCT 207th Yard from a storm surge of the Harlem River. However, after the Contract was awarded and a Notice to Proceed was issued, Walsh Construction Company II (WCCII) partnered with Mueser Rutledge Consulting Engineers (MRCE) to propose a redesign of the marine wall section as a Value Engineering Change Proposal (VECP). This VEP redesign is comprised of 279 each 54in Diameter Steel Pipe Piles that are interconnected with continuously welded PZ 35 sheet piles interlocks. The intent of the VEP was to provide a cost savings that could be shared by both parties as well as alleviate some constructability and alignment control concerns that WCCII had expressed to NYCT. The VEP allowed WCCII to substantially lower the total cost which was shared between NYCT and WCCII.

By C. W. Sheng

In this paper conventional construction procedure is briefly described for the installation of stone columns in soft ground in China. A viewpoint concerning the mechanism of ground improvement by use of stone columns is presented for discussion. Based on the information obtained from field measurement and observation three important problems relating to the construction and design of stone columns are discussed. Finally, a case history is given to show that short stone columns floating within the weak soil layers may in some instance be used to improve the weak strata of great thickness.

Jan 1, 2010

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

By Peter Cali

There is one organization in Sweden, The Swedish Deep Stabilization Research Centre, which has been working with these questions and there is also a project, Eurosoilstab, within European Union to take a manual for deep stabilization.

Feb 10, 2003

Pier, well cap and steining junction is a complicated 3-d re-ion. The prevalent design procedure for the pier, well cap and steining in isolated manner is not rational. In absence of an integrated approach for design of the junction structure, the well cap is designed uneconomical and at the same time pier and steining are left relatively unsafe. Strut-and-Tie Model based design is a simple solution to this problem. An example illustrating design of the junction structure using STM is presented. On comparison of the outcomes of the STM based design with the prevalent design, the following anomalies are found: i) For smooth flow of forces, length of pier at its base should preferably be made equal to the outer well diameter, ii) STM based design for the pier is more rational, economical and safe. iii) Due to presence of hoop stress, as indicated by the STM, the steining concrete in a depth of p times outer diameter of the well from the well cap level should be limited to M15 grade, iv) STM based design for the steining is more rational, economical and safe.

Jan 1, 1996

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

Jan 1, 2017

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Jorj O. Osterberg

The practice of using side shear resistance in the design of drilled shafts socketed in rock is discussed. In the absence of field test data for the particular rock involved, the designer often neglects the side shear altogether or uses an extremely conservative value. The uncertainty of using strength data from compression tests on rock cores is discussed. Examples of full scale load tests are given which illustrate that even in the weakest of rocks, considerable side shear resistances are obtained, enabeling reductions in the depths of the sockets and consequent savings. Existing Practice. The existing design practice in using side friction/bond between a drilled shaft in rock or hard soil varies very considerably in different areas of the U.S., in different areas of the world, among different Geotechnical Engineers, and in the requirements of different building codes. In fact, the variation is so great that it is inconsistent and contradictory. For example, in Florida where fairly weak coral limestone and sandstone is prevalent, the general practice is to use side friction only and to allow no end bearing. In Chicago, Detroit, Boston and other areas where soft clay overlies stiffer clays, hardpan and limestone or other hard rock, the common practice is to allow for no friction and to use end bearing only, even though the lower portion of a shaft frequently penetrates stiff to hard clays and hardpan (glacial till) before bearing on hardpan or rock. In Hong Kong, if the hole is stabilized with drilling mud, no end bearing is allowed. In Boston (Thompson, Erikson, and Smith, 1989), two tests at two sites on 18 inch pipe piles penetrating 100 feet of soft clay and driven only inches into an argillite, tested 140 and 210 tons in ultimate side shear resistance. Certainly, with long drilled shafts, no matter how soft or weak the soil or rock is, some if not considerable side friction occurs, and where drilling mud is used, there must be considerable end bearing.

Jan 1, 1991

By Eric Rehwoldt, Walt Rabe, Jesús Gómez, Tim Myers

"An expansion plan for Washington Dulles International Airport is currently underway to prepare for growth at this northern Virginia facility in the future. While Dulles currently serves more than 20 million passengers a year, when the Master Plan for the Airport is fulfilled, it will be capable of handling approximately 55 million passengers a year. The current Capital Construction Program underway at Dulles will take the Airport one step closer to its full potential.As planned, work includes a new Airport Traffic Control Tower, expansion to existing concourses, a fourth runway, additional parking, and other improvements. One of the most interesting features of this project is the construction of a two-track passenger train system (Automated People Mover, or APM) linking the main terminal and concourses, which will largely replace the Mobile Lounge transportation system, thus greatly reducing surface traffic. Construction of the APM system involves deep excavations along the tunnels and at the transfer stations. This poses special challenges because the settlement-sensitive terminal, original Airport Traffic Control Tower, and concourse buildings, as well as other facilities, exist near the proposed below-ground stations. The site is also underlain by a tight grid of underground utilities that include jet fuel, gas and central communication lines, in addition to more mundane electric, sewer and water mains.One of the most interesting features of this project was the extensive and skillful utilization of micropiles for support of existing structures adjacent to the excavations. Without the use of micropiles, the cost and difficulty of the excavations would likely have been much more. Several important lessons were learned about the use of micropiles, which advance that technology.Throughout the project site, bedrock was generally encountered at 25-ft depths or more. The rock consists of micaceous and highly calcareous siltstone rock. This rock is typical of the sedimentary component of the Culpeper Basin, a Triassic Age geologic feature extending from south central Virginia to western Maryland. The siltstone beds dip gently to the west at about 10 to 20 degrees. Joint planes typically dip 60 degrees to vertical. The rock underlies a sequence of fill materials and residual soils of varying thickness."

Jan 1, 2009

By S. L. Karunakaran

There are cases where it is found that a raft foundation would have adequate factor of safety against ultimate bearing capacity failure but the settlements would be excessive. Piles may be introduced in order to limit settlements to an acceptable level. The actual number of piles required to reduce the settlements to an acceptable level may be very small compared to the number of piles required to transmit the whole structure load. The paper focuses on the difficulties encountered in evaluating the load sharing between raft and piles. An elaborate analysis taking into account the interaction between raft, piles and soil is very complex and time consuming. Few approximate methods for arriving at a satisfactory solution to piled raft system are discussed in the present paper.

Jan 1, 1996

By A. Tejchman

On the site of building of a new flyover founded on piles the comprehensive "in situ" investigations were carried out. The subsoil conditions under each of 15 supports were very differentiated. Using of the static sounding results a new method for evaluation of bearing capacity and settlement of piles was proposed. The method is based on a special construction of the curve of load-settlement relationship. The verification of this method was made on the basis of loading of piles.

Jan 1, 2010

By David White

When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100? of water are well known, let alone in the open waters of the South China Sea. In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130? long, 72? diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE?s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By Jerry A. Steding

How many times have you heard "You can't drive piles because of the vibration."? You hear these words come out of the mouths of owners, engineers, and contractors. When a piling contractor hears this, he can almost always do a psychological profile of the individual uttering these words of wisdom. If the owner makes the statement, we know the odds are about 95% that the owner owns the building next door or he wouldn't care what happens to it; or the guy next door has threatened to sue the owner if he even so much as walks across the site of the proposed new building. If the owner owns the building next door to the new construction you can also be just as certain the old structure has undergone settlement. If the statement comes from the mouth of the contractor, it is usually just a case of him being inexperienced.

Jan 1, 1988

By Gary T. Brill

In the presentation, the development and new applications of the jet grouting technique in the North America are briefly introduced at first and followed by the outline and advantages of Jet Grouting. Several recent projects for jet grouting are presented in which the applications to underpinning and excavation support, foundation, groundwater barrier and seismic stabilization are briefly discussed.

Feb 10, 2003

By A. Ghorbani

The analysis of Combined Pile Raft Foundation (CPRF) is very complex due to involved interactions among components of CPRF system. Many researchers made efforts to develop sufficient methods including three dimensional finite element methods to compute these interactions. Since there are some restrictions and complexity in previous methods, in present study a new approach based on three dimensional finite difference methods is implemented to overcome some of these restrictions. The total and differential settlements of a centrifuge case study are computed using different numerical methods to show the performance of present numerical approach.

Jan 1, 2007