Search Documents

By K. Fujita

In order to deal properly with the fundamental aspects of pile construction, the following problems and their solutions are introduced: For driven piles - stresses, damage, movements of surroundings, compaction of ground, deviation of pile direction and location, selection of pile hammers and penetrability of piles are important factors. For drilled piles -loosening of the ground, supports for boreholes, minimizing ground loosening and defects are critical items. Attention should be given to changing soil characteristics. Also, supervision by experienced engineers and good workmanship by skilled laborers are recommended to ensure the quality of the piles.

Jan 1, 2010

By Stephan A. Jefferis

I presume that the questioner is not asking about the reduction of sulfate in groundwater to hydrogen sulfide as a result of biological activity promoted by organics in the grout hardener and that the question relates to sulfate attack on cementitious grout systems. For the project in Spain presented in my paper, we used a very high pulverized fuel ash (PFA) content in the cementitious material. This gives good sulfate resistance and indeed the chemical interaction will actually cause the permeability to drop for about 50 years without any question of sulfate attack and damage to the whole thickness of the grout - of course there will be attack at the exposed face of the grout where it is in contact with the contaminated groundwater. The mix had over 75% PFA, and also a very high overall cementitious content. The mix was the contractor's design and showed excellent behavior in laboratory proving trials. In grouts as distinct from concrete, PFA gives significantly better sulfate resistance than ground granulated blast furnace slag which is often used in Europe as a component of bentonite-cement mixes for slurry trench cut-off walls.

Feb 10, 2003

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

By Jr NeSmith

"Augered-cast-in-place (ACIP) pile installation technology has matured extensively since the first auger, pressure grouted pile was patented in 1959. The current technology allows for successful pile installation across a variety of stratigraphies to meet various project load resistance requirements. This paper presents an overview of current ACIP techniques by comparing a number of case histories in a variety of geologic settings from Eastern Pennsylvania, New York City and New Jersey to demonstrate ACIP pile constructability in soft soils as well as the penetration, and resulting significant loads resisted, of ACIP piles in dense soils and intermediate geo-materials. Geologic settings that will be discussed include the Piedmont and Coastal Plain geologic provinces as well as glacial till deposits. Keywords: Deep Foundations, Piles, Augercast, Augered-cast-in-place, Auger pressure grouted, ACIP, APGINTRODUCTIONThe author, along with two colleagues, published an article in Deep Foundations magazine (NeSmith et al, 2013) which described a number of the advances in equipment, techniques, installation monitoring and post-construction testing that have expanded the geologies in which Augered Cast-in-place (ACIP) piles are installed as well as increasing their efficiency in some traditional ACIP pile geologies. The author uses the term efficiency to refer to the load resisted by a pile of a certain diameter and the increased efficiency noted refers to increased allowable loads over those traditionally resisted by piles of certain diameter (or a reduction in pile diameter from that which was traditionally used to support a certain design load). The performance and installation of ACIP piles in a variety of geologies in the Northeastern U.S. are discussed herein.PIEDMONT PHYSIGRAPHIC PROVINCEThe Piedmont physiographic province stretches from Alabama to the east through Georgia and up the east coast, just west of the Coastal Plain to Pennsylvania and New York (Brown, 2002). It generally consists of soils weathered in place from the underlying bedrock, which is typically a combination of granite, schist and gneiss depending on the location within the province. The author’s experience in the Northeastern US has been on sites where alluvial or coastal plain soils overly the residual soils and partially weathered or intact rock of the Piedmont. The example presented here, from a site on Walnut St in Philadelphia PA, is representative of these projects."

Jan 1, 2016

By Jiun-Yih Chen

Pile load tests are regularly used to verify pile capacities. Sometimes, they are used to optimize pile designs. This paper presents a case study based on a real project, in which the information obtained from load tests during construction was used to shorten the design pile lengths without a formal decision analysis. In this study, a simple probabilistic model was used to assess the probabilities of failure based on design information. The Bayesian approach was used to update the probabilities given the additional information from load tests. These probabilities were then used in a formal decision analysis to determine the optimal pile lengths based on design information and based on the additional information from load tests. The optimal pile lengths are different from those implemented in the project without a formal decision analysis. The value of the formal decision analysis is illustrated by its ability to optimize the pile length in a transparent and defendable way.

Jan 1, 2009

By H. Shiri

Iran's largest natural gas field is South Pars, geologically an extension of Qatar's 900-Tcf North Field. South Pars was first identified in 1988 and originally appraised at 128 Tcf in the early 1990s. This Field contains 38.6 % of the gas resources of Iran and is regarded as the largest offshore gas field in the world. Offshore geotechnical site investigations are one of the key activities of upstream fields operators to supply the EPC contractors with the required results for designing approaches of offshore complexes. In the mean time a lot of marine site investigations have been carried into execution within the phases of South Pars development. The authors are currently trying to create the fundamentals of investigating the small- and large-scale spatial variability of the South Pars Gas Field in Persian Gulf/ IRAN. Part of this investigation is the providing of an extensive data base of the offshore geotechnical properties of South Pars. Such a data base, will enable a model to be developed of the large-scale variability of these properties. In addition, this data set will provide a data whereby general trends to be established, as well as, providing relationships between geotechnical parameters and spatial parameters utilizing probabilistic and data mining methods like ANN (Artificial Neural Network) in Geotechnical Engineering.

Jan 1, 2006

By Wang Mingshu

The pile foundation is a kind of advanced foundations in the filled or soft soil. In this paper, through the actural engineering of coal dressing plant of Western Opencast Coal in Fushun built on the mining dump with large diameter pile foundation, the construction method and mechanics analysis of pile are given. Unless it is in following stadge, the stability of pile cannot be lost due to its small rigidity. The analysis shows that pile foundations of large diameter ellipse section can decreased hotizontal displacement to 60% ?70% of that of equal section an in the design of a single pile and a single column, the ellipse pile and manual dig hole are most favourable. So a large amount of concrete can be saved.

Jan 1, 1991

By Silvana B. Foá

Results from full-scale loading tests showed the use of the dynamic increasing energy test (DIET) to verify the capacity of deep foundations. This method allows the measurement of dynamic resistance - displacement curve and the prediction of the static resistance -displacement curve of the pile-soil system. The comparison between the use of DIET versus the static load test is also considered herein. This work was divided in two different phases, the first accomplished in Salvador (Bahia) and the second in Brasilia (Federal District), both in Brazil. The first phase consisted of field loading tests carried out on piles comprised by an approximate 10 to 12 meters thick deposit of fine saturated sand, overlying a stiff clay layer, which is found in certain areas of the Brazilian Northeast. Two metallic (rail track) piles were field loaded in this site. One of them was dynamically tested and the other was statically tested. The second site belongs to the Post Graduate Program of the University of Brasilia. It is comprised by an approximate 8 to 14 meter think deposit of porous clay, overlying a hard strata of saprolitic state. In this site a unique precast driven centrifuged pile was tested. The DIET procedure has demonstrated to be a tool of fast execution and low cost (if compared to static load test). It is a promising procedure to evaluate the behavior of pile-soil system.

Jan 1, 2002

By Ting Chinsu

Diaphragm wall with tie-back cable is widely used for deep excavation, especially in the area with high density of buildings. This paper presents the measured earth pressure distribution on diaphragm wall during excavation. The earth pressure cells used in field were successfully installed in deep slurry trench by a new type of simplified manipulator. The sizes of the deep excavation are 26m X 36m on plane and 9m in depth. The construction site is located between two multistorey buildings at the main business section of Beijing city. In this paper the field measurements of earth pressure distribution and the analyses based on the comparison between calculation and measurement are very valuable to improve the current calculation method for diaphragm wall design.

Jan 1, 1991

By Lance A. Roberts

The Federal Highway Administration (FHWA) has mandated the use of the AASHTO Load and Resistance Factor Design (LRFD) specifications for all new federally-funded transportation infrastructure projects beginning in October 2007. This includes the design of all geotechnical-related elements, such as deep foundations, which have historically been excluded from the LRFD requirements. The basis of the LRFD specifications is the application of a probabilistically computed parameter called a resistance factor to the foundation capacity in lieu of the traditional, and often arbitrary, factor of safety. Therefore, the process of computing resistance factors for use in the design of deep foundations is extremely critical to ensure a safe, efficient, and consistent design methodology. In this paper, various methods to calibrate resistance factors for use in the design of deep foundations are examined. The methods that are currently utilized to calibrate the resistance factors reported in the AASHTO LRFD specifications may be classified as the allowable stress design (ASD) method and the reliability theory calibration method using static capacity prediction techniques. These methods are compared to a ?t-z? model design methodology. The current methods focus exclusively on the strength limit state design of deep foundations. The advantage of the ?t-z? model methodology is that it can be utilized for both strength and service limit state design. In addition, the results show that resistance factors vary based on geological setting, construction method, failure criteria and deep foundation type. This variability in the resistance factors should therefore be integrated in the design to ensure that the objectives of the LRFD approach are satisfied.

Jan 1, 2008

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

"Premissas BásicasCaracterísticas do concreto centrifugado(Spun concrete characteristics)Aplicação em obras de engenharia de fundações(Application engineering works foundations)Logística de fabricação e transporte(Manufacturing logistics and transportation)Emendas x uso de aplicação(Amendments x use application)Geologia brasileira, da região costeira a presença de grandes bolsões de argila mole(Brazilian geology, coastal region the presence of large pockets of soft clay)Influencia do sistema de cravação(Influence of driving system)Transferência da Energia Aplicada(Applied Energy Transfer)Estacas longas(long piles)Controles executivos (diagrama de golpes, nega, repique elástico, ensaios de carregamentodinâmico, provas de carga).(Executive Controls (blows diagram, sets, elastic rebound, dynamic load tests, load tests).)ECD – aplicação da metodologia do DIETECD - application of the methodology DIETBrazil has a highly variable geology all along its coast that directly influence the choose of foundation type, being too employed the use of reinforced spun concrete piles initially ranged in diameter from 60 to 80 cm. Over the past 10 years with the advent of investment in marine works projects began to demand a new range of piles with diameters greater than 100 cm and in the absence of amendments.On land is also very remarkable the presence of regions with large layers of soft clay, in prime areas that have been explored. A classic example is the Barra da Tijuca in Rio de Janeiro that has suffered from the housing boom growing toward these regions. In these regions it has been very common driven lengths of about 40.0 meters, which basically go through thick layers of soft material or unconsolidated and they will find strength in depth with residual soil layers or even the bedrock.The spun concrete has great qualities for application in deep cuttings resulting from the production process, which gives a redistribution of fresh concrete mass collaborating with the particle size distribution effective loss of water that is thrown to the center stake being subsequently discarded. Consequently this contributes to a reduction in the factor a/c that is directly connected to increase strength.The fact that there is a sort of concrete helps to reduce voids in the mixture, which increases the durability characteristics. This condition made it possible to employ the spin technique on poles, which are directly linked to aggressive media in large urban centers.Another very attractive feature is that the centrifuge process can work with concrete with the lowest percentage of mortar and more gravel. This concrete mix directly contributes to increasing the specific modulus of elasticity, thus allowing a greater capacity to absorb the energy of the blows transferred with less deformation.Despite the great potential of land application of prefabricated spun concrete stakes there are only three factories and its limitation is the cost of transporting manufactured for the various regions, since all transportation is done by road.For its transportation is carried out exclusively by trucks, this limits the size of cuttings being produced commonly in length from 11.0 to 12.0 meters in length and smaller compositions. For use in long piles of works is resorted to amendments in the form of metal rings, concreted near the ends of the stakes, with the transfer through steel bars in CA-50 welded to the ring. Usually run in steel ASTM A-36. Later in the work these rings are welded with coated electrode.In the case of maritime stakes are very used to drowned splicing technique, which basically consists during the spin process leave one end with the armor of the apparent stake and work together two elements and make specific, with superior resistance to the prefabricated stake.This study in addition to briefly introduce the process of manufacturing, design and logistics presents a detailed study of applicat"

Jan 1, 2015

By George M. Filz

Restrained basement walls and unrestrained but massive concrete walls on rock foundations experience very small movements in response to lateral earth pressures. Such walls are often designed using at-rest earth pressures without consideration of either compaction-induced lateral pressures or vertical shear forces resulting from compression of the backfill in response to self-weight. Compaction-induced lateral earth pressures can be detrimental to the integrity and stability of retaining walls. For example, the lock walls at Eisenhower and Snell Locks on the Saint Lawrence Seaway near Massena, New York, were damaged by compaction-induced lateral earth pressures, and an extensive rehabilitation program was necessary to ensure safety of the locks. Vertical shear forces, on the other hand, can be beneficial to stability because the downwards-directed vertical force tends to counteract the overturning moment from lateral earth pressures. The contribution of vertical shear forces is not included in most modern analyses of non-moving walls, but Terzaghi used this effect in his design of a high concrete retaining wall at Fifteen Mile Falls Dam. The lock walls at Eibach Lock on the Main-Donau Canal in Germany were instrumented for both lateral and vertical stresses applied by the backfill to the wall, and the resulting measurements show that vertical shear forces from the backfill were significant and persistent over the multi-year period that the wall was monitored. Other data from pilot-scale retaining walls confirm the existence of both compaction-induced lateral earth pressures and vertical shear forces. These forces should be considered in design of non-moving walls.

Jan 1, 2003

By Ernest Naesgaard

Post-grouted micro-piles were used for the seismic upgrading of the Vancouver International Airport Domestic Terminal Building (DTB). The micro-piles provided vertical resistance to both uplift and compression loads to supplement the existing timber pile foundations ability to resist the earthquake induced forces, and to provide foundation support at locations where the installation of traditional driven piles was difficult. This paper describes the site conditions, design rationale, installation method and quality control testing procedures. Site and Subsurface Conditions Vancouver International Airport is located within the central portion of Sea Island, Richmond, British Columbia (Fig. 1). Sea Island is bordered by branches of the Fraser River on the northeast and south sides and the Strait of Georgia along the west side. The natural grade of the island is part of a large delta that has been built up over several thousand years. The general pattern of sediment deposition has followed the direction of the Fraser River flow from east to west, and has built up soft sediments of about 200 m thickness at Sea Island (Luternauer, et al. 1993, Mathews and Shepard 1962). The original grade in 1962 prior to the existing Airport Terminal Building development was at about geodetic elevation 1.1 m with a grass and topsoil cover.

Jan 1, 2004

By Peter Iovino

Unfortunately, I don't know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don't think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003