Search Documents

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

Minerals are fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels?mining, processing and manufacturing finished products. The estimated growth rate for the real GDP of the United States was 2.1 percent and the nominal GDP was about $13.8 trillion in 2007 (Table 1). The prime interest rate decreased to 7.25 percent in December from 8.25 percent at the beginning of 2007, reflecting actions taken by the Federal Reserve Board to counter financial difficulties surrounding subprime mort-gages. Delinquencies on subprime mortgages increased throughout the year, affecting not only the delinquent home owners but also financial instruments invested in mortgage-backed securities. The average contract mortgage rate for the purchase of previously occupied homes in the United States was 6.35 percent in November; a slight decrease from 6.37 percent in January but still greater than 5.34 percent reported in July 2003, the lowest rate in the past five years. With the tightening of credit, the seasonally adjusted annualized rate for new privately owned housing starts declined 27 percent from December 2006 to November 2007. The loss in the residential market was balanced by a 9-percent increase in nonresidential construction between January and August 2007, during which slight increases occurred in nearly all

Jan 1, 2008

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By Qing Bo

In this study, the cobalt oxide precursor was prepared in open-style reactor in the condition of high reactant concentration, and then the precursor was decomposed to obtain the cobalt oxides (Co3O4). The effects of some factors on the cobalt precipitation, the particle size and size distribution, and the micro-morphology were addressed. The factors studied include cobalt concentration, initial pH of solution, temperature and time for the reaction, the charge amount of urea, and the temperature for decomposition. It is determined that the precursor particle is in the chemical composition of Co2(OH)3Cl with fine crystalline. By calcinations under proper conditions, the mono-dispersed cobalt oxide particles were prepared with fine crystalline, about 2 µ m in particle size and regular shape in morphology.

Jan 1, 2006

By Raymond J. Pichette

"Aeromagnetic data can be useful in helping to delineate structures and rock types in gold exploration. Magnetic anomalies associated with Archean volcanic belts in northeastern Ontario can be quickly and effectively analyzed in profile form with the use of model curves. The model curves help to locate contacts between strata. They also help to estimate the magnetite content of the rocks and their depth beneath overburden.An aeromagnetic map of part of Catharine Township, Ontario has been analyzed with the aid of model curves. Several magnetic rock types, potential fault zones and areas of relatively thick overburden were delineated.IntroductionIn any exploration program, a good understanding of the stratigraphy, rock types and structure enhances the possibility of success. For example, environments which host gold deposits in the Abitibi Volcanic Belt may be characterized as follows (Jensen, 1980; Pyke, 1980):(I) They have major faults, especially as tectonic boundaries between volcanic piles which include mafic and ultramafic rocks and clastic sedimentary rocks or gneisses.(2) They have subvolcanic felsic intrusions.(3) They have extensive carbonitization, with or without carbonate and sulphide-facies iron formation.In all cases, delineation of structure and rock type should be a major objective in exploration. The analysis of magnetic data can be a useful tool in this task. This paper is presented with the purpose of describing the application of the magnetic method to gold exploration in Archean volcanic terrains.Magnetic AnalysisTotal-intensity magnetic contour maps can be used to discriminate rock units according to differences in magnetization. However, because of smoothing of texture resulting from the compilation procedure and the fact that survey lines are widely spaced, contours should not be directly used for quantitative analysis. A much more definitive means of magnetic analysis is provided by the use of the original profile or chart recordings. Model curves provide a basis for analyzing these profiles both accurately and rapidly."

Jan 1, 1982

By Johnson I. R, Muir M. D

The Dugald River zinc-lead deposit is located 60 km northwest of Cloncurry. It was discovered prior to 1881, and since 1937, has been the subject of several drilling programmcs which have outlined a resource potential of 60 million tonnes grading 10 per cent zinc, 1 per cent lead, and 30 g/t silver.The deposit is a classical example of stratiform zinc lead mineralization in a black shale host. It occurs within a restricted clastic sedimentary basin within the Corella Formation of Carpentarian (Middle Proterozoic) age. Sabkha, lacustrine and fluvial sedimentary environments have been recognized within this basin. Each environment is characterized by suites of evaporite mineral pseudomorphs, after both shortite and gypsum, indicating that both alkaline and hypersaline environments prevailed at different times during basin evolution. The Dugald Slates which host the zinc-·lead mineralization are lacustrine in origin. Thin Mount Isa-type K-rich tuffite beds occur in the Dugald Slates and in the sabkha sequences.The basin as a whole appears not 10 have been marine, and 10 have had strong tectonic controls on its depositional history.The mineral deposit itself is conformable within the Dugald Slates and many primary sedimentary and soft-sediment deformation structures are preserved. It has a strike length of 2 km, average width of 10 m, and a westerly dip of 50-80 . Drilling suggests continuity to 1000 m vertical depth. The predominant sulphides are pyrrhotite, pyrite, sphalerite and galena in graphitic slate and quartz-carbonate ganguc. Anomalous concentrations of barium, manganese, cadmium, mercury and antimony are present in the ore.The deposit crops out over a distance of 2 km as a gossan ranging from 5-15 m in width. There is a striking vegetation anomaly over the gossanous outcrops. The gossan is enriched in lead, silver, antimony, barium, titaniulll, silica and iron, with respect to the primary mineralization. The depth of total oxidation reaches about 20 m.Cieochemical and geophysical test surveys over the deposit give pronounced anomalies.

Jan 1, 1982

By Cynthia Belt

"Before energy can be saved in the materials industry, the process must be understood. At the same time, baby boomers are starting to retire. New people are entering the field without experience and training especially in methods to save energy. Various classroom courses, seminars, books, software, and websites are available for the professional to better understand the industry with the ultimate goal to reduce energy use. This paper is a review of what is currently available with some comments on potential needs.IntroductionEnergy use is high within the materials industry. For the United States, the primary metal industry uses 8% of all energy used in manufacturing (Figure 1 )1 or 1, 736 trillion BTUs per year. Sadly, while energy use is high, energy management is not universal within the industry. Counting both internal programs and external such as the utility supplier, equipment manufacturers, federal and state programs, only 66% of primary metals companies participate in an energy management activity1.For the materials field, process heating is the majority of the energy use in a plant2. Understanding and optimizing process heating is a critical need for materials energy professionals. Surprisingly, process heating is not necessarily the work addressed within an energy program. The U.S. 2006 Manufacturing Energy Consumption Survey (see Table 1) found more primary metal companies addressing lighting with 31 % participation versus 15% with process heating work even though energy used in lighting tends to be a minor (in the range ofl-3% ofa typical plant's energy use)."

Jan 1, 2013

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

Although auriferous beach and fore-dune sands at Five Mile Beach south of Okarito township had been intensively mined by hand and primative mechanical methods drilling of the sandspit by the Gold Development Corporation in 1929 indicated that the grade and quantity of undisturbed black and grey sand below the water table was sufficient to support a mining operation. Worked sand above the water table also contained fair prospects. The Okarito Five Mile Beach Gold Dredging Co Ltd, was formed and an hydraulically powered, bucket ladder, sluice box dredge built. In 13 years of operation (1931 - 1943) the dredge returned 556.39 kg (17 890 oz) of gold at a recovered grade of 225.4 mg/m3. A total of ú42 000 was distributed as dividends on the ú30 000 capital investment. Recent drill and bulk sampling at the northern end of the beach has confirmed that reworking of the historic tailings by a modern gravity recovery plant would not be economic.

Jan 1, 1993

It is widely accepted that particles stabilise flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Dynamic surface tension measurement using maximum bubble pressure presents an attractive technique to investigate the effect of surfactant and particles at the air-water interface. The range of bubble lifetimes that can be studied (typically 0.1 to 60 s) is analogous to variations in air rate in flotation cells, and the corresponding changes in surface tension give an indication to the diffusion and adsorption rates of particles at the interface. In this paper, we use dynamic surface tension measurements to investigate the effect of particles on bubble surfaces at the microscale and link this to bulk froth stability measurements carried out using a froth column. Using the maximum bubble pressure method, the results show that the addition of particles results in lower surface tension, both at the dynamic (i.e. short) bubble lifetimes and towards equilibrium (i.e. 60 s bubble lifetime). This corresponds with the bulk froth stability measurements, where the three-phase system yielded more stable froths than the surfactant only system. Furthermore, increased particle loading at the air-water interface, whether through higher surfactant concentrations or lower air rates (longer bubble lifetimes), gave lower surface tension and higher froth stability. This demonstrates the link between bubble loading and froth stability. It is proposed that the maximum bubble pressure technique can be used to predict froth stability for two- and three-phase systems, enabling the effect of particle loading to be accounted for and quantified. Moreover, the technique has the potential to allow rapid determination of particle and surfactant diffusion at the air-water interface and prediction of the corresponding effect on bulk froth behaviour.

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

Diesel Particulate Matter (DPM) issues are very high profile currently in both Australian coal and metal mines and Australian states are generally moving to acknowledge and to broadly follow US 2008 final metal/non metal mine regulation limits of 0.2 mg/m3 submicron particulate matter, 0.16 mg/m3 total carbon particulate and 0.1 mg/m3 elemental carbon particulate. The real time DPM monitor is being developed on the base of the successful Personal Dust Monitor (PDM) unit. The objectives of recently completed Australian Coal Association Research Program (ACARP) study has been to finalize the design of a DPM unit, to undertake comprehensive and internationally recognized laboratory testing to evaluate the new design and to undertake an underground series of tests to establish the robustness and reliability of the new approach. Under the project Thermo Fisher Scientific has undertaken structural changes to the PDM to convert it to a DPM real time monitoring underground instrument, the D-PDM. The Pennsylvania Pittsburgh Research Laboratories of NIOSH (the group that originally contracted for the PDM development) has undertaken laboratory ?calibration or verification? testing. A phase of Australian mine robustness and engineering testing has been undertaken to ensure the instrument can effectively assist mine management to handle this health issue. Tests have been undertaken at points of expected high atmospheric DPM such as during Longwall face moves, Development RAM car, Eimco and PJB usages. The paper discusses how the monitors have performed within the underground mine environment in evaluating DPM during the various phases of the production cycle. They have closely examined the influence of aspects of the mine ventilation system. Results have been compared to alternative industry pollutant measuring approaches. The outcome of the project gives the industry access to an enhanced tool for understanding the mine atmosphere in the presence of DPM. Real time DPM monitoring will allow the industry to pin-point high exposure zones such as those encountered in coal longwall face moves where various vehicles work or in areas of constrained or difficult ventilation. Identifying of high DPM concentration zones allows efficient modification of work practices to reduce underground miners? exposure. Some outcomes of the ACARP project in this area will be discussed.

Jan 1, 2009

IN a mine with any considerable output the economical handling and transport of ore underground is a matter of prime importance, and in the design or lay-out of a trucking system the question of what form the points and crossings are to take should be one of the first considered. Trucks may be moved from one line of rails to another by the following means: by flat sheets, with which may be coupled turn-tables, or by points and crossings. The latter class may be further divided into fixed and movable points.Flat sheets and turn-tables, owing to the time and skill needed by the trucker in using them, are seldom of great value with large tonnages, unless for purely temporary work, and the choice narrows down to one between fixed and movable points andcrossings. Both systems have their disadvantages - movable points being liable to jamb with dirt and get out of order, whilst with fixed points trucks may sometimes run over the points and capsize, or go on to the wrong line, though this is not of frequent occurrence. On the other hand. the fixed points are simple, easily laid, and strong, and there is no necessity for the trucker to work any levers, the truck being guided on to its new direction by screwing.Cast-iron points and crossings were first introduced into the North mine during the opening-up of the 950-ft. level, and the first arrangement was designed for a double turn-out in the main crosscut. Since then both the points and crossings have beenmodified several times, and it may be interesting to briefly outline the various forms through which they have passed, showing the reasons for the retention of some features and the rejection of others.

Jan 1, 1915

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.' This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,' which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.' The fracture path in ß brass is predominantly transcrystalline,' in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By A. J. Kauffman

This inventory of the industrial mineral resources of the Pacific Northwest indicates that each of the States comprising this great region annually produces nonmetallic materials valued at mans million dollars. Commodities or their products that have a large, localized market predominate. These include Portland cement, sand and gravel, stone, clay, and lime. The region's output of magnesite, vermiculite, pumice, and diatomaceous earth is outstanding. The magnesite deposits of Stevens County, Wash., are the largest and most important in this country. Mast of the domestic vermiculite production is obtained from deposits in Lincoln County, Mont. Oregon and Idaho rank third and fourth, respectively, as domestic pumice producers. Production data for diatomaceous earth show Oregon second and Washington fourth among the producing States.

Jan 1, 1952

The concept of a magnetic hydro-cyclone is undeveloped, possibly because studies by Bragard (1965) and the Royal School of Mines in London (Robinson, 1965) were not encouraging. Its role for the concentration of ironsands is attractive in that the classifying effect within a hydrocyclone may be comparable to the classifying effect in the gravity concentration of ironsands, and thus two steps may be achieved in one. Furthermore it should be a very simple and cheap process. The idea has been explored intermittently since 1976 but more energetically since the offering of a magnetic hydro-cyclone thickener by Boxmag Rapid (1983). This paper summarises the development and test work which are detailed elsewhere (Fricker, 1984).

Jan 1, 1984

Copper ores are widespread through the Lachlan Geosyncline in New South Wales, but the size of the orebodies is generally small. The largest deposits occur in the Cobar district where an iron-rich copper ore type has been developed in Silurian sediments. Similar de- . posits to the south in the Nymagee-Mt. Hope-Melrose districts are related to quartz feldspar porphyries of probable Upper Silurian age. Deposits to the east in the Tottenham-Girilambone districts are less complex mineralogically and are possibly related to an ultra-basic source.Copper mineralization in the Highlands further to the east is often developed in Ordovician andesite or MiddleUpper Silurian acid volcanic sequences. The deposits in andesite contain considerably less galena than those in the acid extrusives; a small proportion of the mineralization in the latter has texture, mineralogy, and geologic setting analogous to the Captain's Flat copper-Iead-zinc deposit, for which both syngenetic and epigenetic origins have been proposed. Very little copper mineralization occurs within granitic material, even though rocks of this type ranging from Silurian to Carboniferous in age crop out through much of the geosyncline, and the extent of the metal contribution from plutons to the deposits in volcanics is open to question. Numerous deposits are known in the contact zone around Mid-Devonian and Mid-Carboniferous granites, however, and the formation of these orebodies has undoubtedly been influenced by plutonic activity. Small occurrences of copper with associated minor nickel sulphides are developed in a narrow serpentinite belt of possible Lower-Middle Devonian age in the southern section of the Highlands.

Jan 1, 1970

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965