Search Documents

By E. Stoetzer

In all known deep mixing processes the existing soil is mixed with self hardening slurry by mixing tools that rotate about a vertical axis (augers, mixing paddles). Wall panels are constructed using sets of multiple mixing tools combined into a single unit. These techniques have been developed on the principle of the rotary drilling technology. In contrast, the new Cutter Soil Mixing or CSM technique is derived from the cutter technology. The soil is loosened and broken down by cutter wheels, then mixed in-situ by the rotating cutter wheels with the self-hardening slurry - introduced into the ground between the two wheels - to form a soil-slurry mortar. The main area of application lies in the construction of cut-off and retaining walls.

Jan 1, 2006

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

It is easy to demonstrate the importance of aggregates in any conversation about infrastructure and other engineering artefacts. Peoples around the world have made use of stone to enrich and enhance their lives since the earliest days of civilisation. In New Zealand, Maori used hard durable rocks for weapons, tools, and basic structures. European settlement accelerated the use of quarried materials and formed the basis for development of our society as we see it today. Logic might suggest that the quarrying sector would be recognised positively for, and encouraged to continue to contribute to, this underpinning of the way we are. The reality is æNot In Most Back YardsÆ. Why? The rock is where it's always been (often overlooked) and our æsocialÆ environment is today's hard place. For a resource-based business in New Zealand, that environment is principally the Resource Management Act, with the widespread power it has distributed to anyone prepared to invest their time. This coupled with a lack of leadership and direction in the implementation of the Act has created a climate that stifles development and diverts energy and resources to æplaying the gameÆ rather than ælifting the gameÆ. Perhaps the real costs of this are not yet widely recognised. The paper will draw mainly on the experience of endeavouring to consent a ægreenfieldÆ quarry in the Waikato region. This is supported by commentary based on nearly 10 years of ælivingÆ with the RMA at sites across much of New Zealand. RMA Scorecard Summary: Effects based? Rarely. Level playing field? No. Maori Consultation? Could do better. Efficient use of resources? No. Timely? No. Is it working for other sectors? Certainly not the quarrying industry's customers and end users.

Jan 1, 2000

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By Finlayson EJ

Epithermal gold is hosted by late Middle Miocene Okiduse Volcanics on Woodlark Island. Dating of associated alteration minerals indicate mineralisation to be broadly contemporaneous with volcanism (12.2 - 12.5 m.y.) and is probably related to subduction of the Solomon Sea plate along the Trobriand Trench. Mineralisation is polymetallic and structurally controlled. Pyrite, sphalerite, galena and minor chalcopyrite occur in steeply dipping fracture zones and/or hydrothermal breccia bodies associated with mixed clay-pyrite alteration envelopes. These envelopes occur within a terrane of regionally propylitised high-K, calc-alkaline andesites and related epizonal subvolcanics. Gangue minerals include quartz, calcite, dolomite and minor anhydrite. High level advanced argillic alteration and siliceous cap rocks are not present but may have been eroded off the top of the system. Fluid inclusion and stable isotope data suggest that the carbonates and paragenetically associated auriferous base metal sulphides probably deposited from an isotopically evolved (+8%. 180) reduced hydrothermal fluid sourced from underlying sedimentary rocks. The fluid was predominantly of low salinity (0-4 wt % NaCl equivalent) and had a temperature of about 270¦C at the time of boiling and mineral deposition.

Jan 1, 1987

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

By W. J. González

"With the increasing demand for minerals, technologies to maximize mineral recovery are paramount to a mine’s economic success. Many mining process waters have the potential to form calcium-based inorganic scales, which inhibit effective mineral recovery. Often, the solution to inhibit these deposits is the implementation of a chemical antiscalant program. This paper examines the application of a fouling analyzer to continuously monitor the formation of inorganic scale in mining process streams. The fouling data can be used to compare antiscalant programs and to optimize antiscalant feedrates. Case studies validate the ability of this technology to help optimize mineral recovery processes.INTRODUCTION The mining industry uses significant quantities of water. From quarrying, to crushing, to flotation, leaching, and refining, water is often the integral motive force to move slurries, separate or agglomerate fines, and extract and purify minerals. As well, water is used in a number of ancillary applications at mines, including dust suppression, gas scrubbing, and utility processes such as boiler, cooling, and waste water operations. For many processes, the quality of water being used is inconsequential. However, for certain processes, such as flotation, leaching, and desorption / stripping, water quality plays a key role in the ability of the operation to economically recover the target minerals. Dissolved solids such as calcium and magnesium salts can concentrate in process waters, exceed their solubility limits, and precipitate as scale on metal surfaces such as feed and transfer pumps, piping, and equipment. Some of the more common scales that form in mining operations include calcium carbonate (CaCO3, or calcite) and calcium sulfate (CaSO4, or gypsum), and to a lesser extent, calcium and magnesium silicate compounds. Any scale that deposits in a process stream will negatively impact mineral recovery, and increase the operational costs of the mine site. Whether it is acid washing a scaled heat exchanger in a carbon strip at a gold operation, replacing plugged emitter tubes in a leaching operation, or hydroblasting process lines in a scrubber unit, there are costs associated with labor, cleaning chemicals, repairs, and replacement parts. These costs pale in comparison to the potential costs of downtime and lost production, should the scale deposits occur in a process that is critical to the recovery of the target mineral."

Jan 1, 2014

By R. S. Dean

This is the fourth of a series; of annual report of the Metallurgical Division to be released in this form and cover the fiscal year July 1, 1937, to rune 30, 1938. This report is not merely a recitation or brief of the year's work; it contains technical information in usable form, although a some of this has appeared or will he issued in greater detail in separate reports. The table of contents that follows fists the principal investigations accomplished and those that are being continued. Other projects are being begun and contemplated for the next year.

Jan 1, 1938

By Milton H. Fies

To present some idea as to how the Bureau of Mines may most effectively serve mining, it is necessary that we make some resume of its pact accomplishments in order to determine what, if any, changes will be of greatest service to the industry and to the nation. There are a great many times in life when one begins to wonder whether or not Emerson, in his famous epigram about "mousetraps" and "beaten paths" and "final recognition of intrinsic worth", took into account the item of time. The intrinsic value of any movement, of any work, of any accomplishment will ultimately be recognized, of that there is no doubt, but may a man in history has gone to his end in martyrdom because the world was slow in the acknowledgement of the true excellence of his worth, and this is likewise true of institutions.

Jan 1, 1934

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

In late 1989, first-pass reconnaissance exploration delineated a 4km x 6km geochem- ically anomalous area centred 10km WNW of Kainantu in the Eastern Highlands Province at 6¦13'S and 145047'E. The area, named the Basangka prospect, lies between 2 200 and 2 400m asl. Interest in the area was prompted by a 14ppm Au assay of a silica-pyrite breccia float sample taken near Henkai village. The prospect was defined after several acid-leached silica- pyrite breccia and comb textured quartz float samples returned assays above lppm Au and relatively high Ag. Very encouraging and anomalous Au values were obtained from panned concentrates, despite the absence of visible Au colours. Several pan concentrates returned greater than 1mg Au and it is believed that the Au occurs as inclusions within iron oxides which were originally pyrite. In this early stage of prospect exploration, any Au value above 0.lppm in- 150# fraction stream sediments is treated as anomalous. Rock chips, panned concentrates and -150# fraction geochemistry all vividly define the areas of interest at Basangka.

Jan 1, 1991

Rock engineering has now been practised as a discipline for about50 years, and many sophisticated methods of analysis for use in rock engineering design have been developed. However, analysis is only a tool for use in engineering design, and rock masses are often so complex that realistic modelling of them, even with sophisticated methods of analysis, is impossible. At the other end of the scale, rock mass classification methods have been developed to quantify the rock mass. These ?numbers? are now widely used for assessment of stability of underground and surface excavations in rock, for the determination of rock support requirements, and for the estimation of rock mass strength and deformation properties. In considering these areas, the two concepts?design, and prediction of behaviour?will be dealt with. The discussion will be introduced by a consideration of the characteristics of the rock mass, which will highlight the variability in its properties and hence the uncertainty in the behavioural parameters. Examples of real projects will be used to illustrate the discussion.

Jan 1, 2003

Gold in the stibnite veins of Costerfield, Victoria, was described in 1922 1, prior to any mineragraphic examination, as (a) free yellow gold (b) free rusty gold and (c) combined gold. The free yellow gold occurs in quartz and will amalgamate with mercury. The free gold of dull, rusty or copper-red colour occurs in massive stibnite and has been stated to resist amalgamation with mercury. The dull colour is only skin deep and the colour is bright when the rusty gold is scratched. The appearance of the rusty gold is spongy or cellular and it generally occurs near small cavities in the stibnite. The suggestion that the cellular character indicated the removal of a certain amount of stibnite leaving a residue of se.condary gold cannot be sustained.It now appears probable that the rusty gold is formed by the primary dissociation of a gold antimonide and is distinct in origin from the normal yellow gold which is deposited with quartz or stibnite from auriferous mineral solutions.The combined gold referred to in the earlier paper was the gold contained in the stibnite as revealed by assay. Such gold was at first thought to be either dissolved in the stibnite or else present as free interstitial particles too minute for observation in transmitted light in thin sections.Subsequent examination of numerous polished,surfaces disclosed the small particles of gold occurring in the grain boundaries in aggregates of fine grained stibnite 2. The assumption that all the gold in the stibnite, as revealed by assay, occurred in this way is now known to be incorrect, because limited amounts of a gold antimonide have been found in the veins.

Jan 1, 1952

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic-Upper Permian sequence, and has enabled the upper part of the lllawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in the survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the upper part of the llawarra Coal Measures, as revealed by the seismic reflection survey.A synclinal axis striking at approximately 55° has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by combined analysis of seismic and magnetic results.

Jan 1, 1970

By S. Asokan, CVGK Murty, R. Upadhyay

The principal mineral sources of titanium are rutile, anatase (both TiO2), ilmenite (FeTiO3) and leucoxene (a weathered ilmenite of variable concentration of TiO2 but similar to pseudorutile Fe2Ti3O9). These titaniferous minerals along with their value added products like Synthetic Rutile and TiO2 slag constitute ?Titanium Feed-stocks? for TiO2 pigment, Ti metal and welding electrodes industries. Unlike in other industries, the demand driver for titanium minerals is not the metal, but the TiO2 pigment ?a specialty chemical. Of the total titanium feedstocks usage in the world, about 93 % is consumed in TiO2pigment, with only about 3 % is utilized in metal production. India?s heavy mineral sands resources are among the largest and also one of the richest grades in the world. The country?s Ilmenite resource base stands at 348 million tonnes of Ilmenite (18% of the total world reserves)along with 18 million tonnes of Rutile, 21 million tonnes of Zircon, 8 million tonnes of Monazite, 107 million tonnes of Garnet and 107 million tonnes of Sillimanite. Though the grades (Total Heavy Minerals (THM) present in the sand) of Indian deposits are relatively rich, the contained ilmenite are termed as sulphate grade with 50-53% TiO2 (Chavra deposit of Kerala and Ratangiri deposit of Maharastra are an exception with 60% of TiO2). While superior grades with adequate reserves lead to a cost advantage in ilmenite production, the lower TiO2 percentage allows the direct use of Indian ilmenite only in the production of TiO2 pigment through sulphate route and for the chloride pigment production; such ilmenite is required to be upgraded either to Synthetic Rutile (SR) or TiO2 slag. However, in order to produce TiO2 slag in India at a globally competitive cost, the issues like high power tariff, inadequate infrastructure, expensive logistics, less enthusiastic market preferences, supply-demand gaps are to be adequately addressed. This paper deals with some of the above issues and possible solutions thereto in production of TiO2 slag from Indian ilmenite.

Jan 1, 2007

By Elaine R. Goetz

The eastern and southeastern regions of Ohio are part of Appalachian coal country, with a documented 1,300 miles of streams impacted by acid mine drainage. Since 1995, partnerships of local watershed groups, government agencies, private industries and universities have focused on the remediation of the affected waterways. The partnerships have spent $2.4 million annually in constructing and operating treatment systems such as wetlands, anoxic limestone drains, successive alkalinity production systems, steel slag leach beds, and lime dosers. These systems have been partially successful, and water quality has improved in the region, but no treatment has yet met the ultimate objectives of low cost, continual remediation. Our research group has investigated an alternative system for acid mine drainage treatment: electrolysis combined with pH adjustment to selectively precipitate recoverable, saleable metal products to offset the cost of treatment. We utilized a $0.2 million pilot facility constructed by the Wayne National Forest, in Nelsonville, Ohio, to process approximately 40 L/min of mine drainage from surrounding seeps. The pilot facility has multipurpose tanks that can be adapted to process acid mine drainage with different characteristics, such as high or low aluminum content or high or low carbonate concentrations. Sodium hydroxide was used for pH adjustment. Results indicate that saleable product can be generated with this treatment technology. In an initial, not optimized trial, one seep yielded 4.7 kg of dried 69 % iron oxide product from 10 hours of pilot facility operation, treating 23,000 L with electricity costs of $4.68. Dissolved iron concentrations in the water were reduced from 242 ± 18 mg/L to 2.8 ± 2.0 mg/L (99.0 % removal) while the initial acidity of 443 mg/L as CaCO3 was neutralized to an alkalinity of 160 mg/L as CaCO3. Iron oxide can be sold as pigment for an average of $1.47 per kg in the United States. Currently, approximately 80 % of all pigment used in the United States is imported, and there is incentive to purchase domestically recovered pigment. If the iron oxide from the pilot facility could be sold as pigment for $1.47 per kg, 43 % of the operating cost (raw materials, electricity and construction costs) of treatment could be offset by the sale of the product. Considering the cost offset, the electrolysis process shows potential as a sustainable low cost alternative for treating acid mine drainage.

Aug 1, 2013

By A. Fahimifar, H. Soroush

Abstract: In order to develop non-destructive methods in studying physical and mechanical properties of rock and replacing them with difficult and expensive static methods, several ultrasonic tests were carried out on cylindrical rock specimens in accordance with the ISRM suggested methods and velocity of P and S waves were determined. Also, density, porosity, water absorption, uniaxial compressive strength and indirect tensile strength were determined for each specimen in accordance with ISRM suggested methods. According to above tests static and dynamic elastic constants were calculated After statistical analysis of data obtained from tests, the relationships between velocity of elastic waves and physical or mechanical parameters were determined and some equations were obtained. Also similar analyses were performed on static and dynamic constants and some equations were extracted. Using these equations, the physical and mechanical parameters of rock and also static elastic constants can be estimated by conducting simple and quick tests (i.e. ultrasonic tests). Abriß: Um zu entwickeln, die zerstörungsfreien Methoden für Studieren die physischen und mechanischen Eigentümer von Steinen und auch ist für Ersetzen diese Methoden mit schwierigen teuren statischen Methoden, mehrere altrasonic Prüfungen auf zylindrischen Steinproben gemäß ISRM anregenden Methoden und den Geschwindigkeiten von S und P Wellen bestimmt worden sind durchgeführt worden. Außer der Dichtheit und der Porosität betonen Wasser Aufnahme und monoaxial Widerstand und dehnbaren indirekten Widerstand jeder Probe betreffend der erhaltenen Ergebnisse die atmosphärische Aufladung sind bestimmt worden und die dynamischen Faktoren der Steine sind kalkuliert worden. Nachdem statistische Analyse die Korrelation der Ergebnisse zwischen der Geschwindigkeit elastischer Wellen und mechanischer und physischer Eigentümer der Steine erhalten worden ist, und mehrere Verhältnisse sind vorgeschlagen worden. Eine ähnliche Analyse ist auf atmosphärischer Aufladung und dynamischen Faktoren durchgeführt worden und einige Verhältnisse sind erhalten worden. Mit Hilfe dieser Verhältnisse die physischen und mathematischen Eigentümer von Steinen und auch können die Statistik Faktoren durch einfachen und schnellen altrasonic Prüfungen erhalten werden. Resume: Puor le development des method non-destructive et evaluuation des propietes physical et mechanical des rock et superseding avec les methods dificzle et cher statique, c‘ est fait plusieur essayes ultrasonique sur les echantillons cylinrique et par a port le proposale TSRM et le vittesse des ondes P et S et densite et porosite et absorption des eaux le resistant de pression uniaxial et resistance de chaque echantillon est determinee. A la fin en base des resultat obtenue les constant statique et dynamique des roches sont calcule. Apres les analyses statistiquc sur les resultat obtenue du les essaybs, c‘ etait produit les relation entre les viptesse les ondes elastique et les proprietes physic et mechanicue des roches et c est propose quelque relations. Aussi le meme enterpretation sur les constant statique etdinamique. En possezon de ces relations, les spesificatio physique, aussi on peut trouver leur constant statique, avel les essayes sample et raptid a d ultrasonique.

Jan 1, 2003

By F. Mielli

Camera systems and video surveillance are usually associated with people and asset protection. However, they can be applied in a mine environment beyond conventional surveillance: For process monitoring, collision avoidance, sizing, flotation cells, conveying systems, blasting, objects and people tracking, thermal profile, and to automatically identify equipment that is missing parts,. Image and video solutions can be driven by better integration of powerful video analytics and cameras systems in automation tools such as process controllers and supervision systems.

Feb 27, 2013

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By J. D. Davis

THIS-report gives results of in investigation of the carbonizing properties of 18 coals, including 2 from Alaska, 12 from British Columbia, 3 from Washington, and 1 from Utah. Each coal was carbonized in the standard 13-inch Bureau of Mines-American Gas Association (BM-AGA) retort at 900° C. Plastic properties were determined by the Gieseler and Davis methods, and agglutinating and free-swelling properties were determined by standard methods. Expanding properties were measured in the Bureau of Mines sole-heated oven. From the results of the tests on these single coals, three coals from the Crowsnest area in British Columbia, representing Elk River Nos. 4, 9, and 10, were selected for blending with the Utah coal, which was from the Lower Sunnyside bed, Horse Canyon mine, Emery County. Lower Sunnyside also was blended with Wilkeson -Nos. 2 and 3 (Washington) coals, Pocahontas No. 3 from McDowell County, W. Va., and the Oklahoma low-volatile coal used in the blend carbonized at, the Provo, (Utah) coke plant at the time this investigation was started. Most of the blends contained 3 percent hard pitch, which is the proportion used at the Provo plant. The blends were also carbonized in 13-inch BM AGA retorts at 900° C. High-volatile B coal from the No. 3 bed, Evan-Jones mine, Lower Matanuska, Valley, Alaska, yielded poorly fused coke or char. M-bed coal from the Chickaloon mine, Upper Matanuska. Valley, Alaska, ranked as medium-volatile bituminous and coked strongly. It expanded 39.6 percent in the sole-heated oven at a. charge density of 55.5 pounds per cubic foot..

Jan 1, 1952