Search Documents

By Mukhopadhaya K. K, Cory A. H

The concept of using travelling magnetic fields created by linear motors was stimulated by Laithwaite who advanced ideas on motors with shaded poles (Laithwaite, 1968), rack and pinion motors (Laithwaite, 1970) as well as low speed, brushless motors and three dimensional motors (Laithwaite, 1973a and 1973b).Sudan (1963) and Sundberg (1969) had applied the concept to metallurgical processes. However, the use of travelling magnetic fields has not been used widely to produce conditions for the separation of magnetic from non-magnetic minera1s or even magnetic materials from non-magnetic materials, although some attempts were made by McCarthy (1922), Davis (1934), Dean, Gottschalk and Davis (1934) and Gottschalk (1934).Laithwaite (1973, a) while working with linear motors made suggestions for designing separators and in the work described here, the observations of Laithwaite and others are extended to determine the characteristics of the motor with a view to using it as a magnetic separator.

Jan 1, 1980

By Met M. E, Worner H. K

During the past two years, a large number of creep tests has been carried out on electrolytic lead, special assay lead and ordinary refined (Port Pirie) lead. Some of these tests have already been reported.1§ In addition, an attempt has been made to estimate the influence of the individual elements present in small traces in Port Pirie lead. The present paper gives the results obtained when small additions are made to "U" lead of the composition shown in Table 1.(which has been used throughout these investigations during the past few years). The additions were silver, antimony, bismuth and zinc. The results of the addition of tellurium have already been communicated. This investigation was intended to run parallel with a similar one using electrolytic lead as a basis and adding one element at a time.Actually, the experiments using "U" lead have got rather ahead of the others. The important point has emerged, however, that the effect of a .given addition may be appreciably influenced by the presence of traces of other elements.In most of these tests, an initial stress of 500lb. per sq. in. has been used. Whilst it is fully appreciated that this stress is higher than those used in practice, it has to be borne in mind that an improvement in creep resistance was *Manuscript received December 11th, 1936.

Jan 1, 1936

By James P. Sloss

WHAT is the likelihood if any-that a real gold mining industry will be developed in the southern Appalachian region? Has the increase in the dollar value of gold from $20.67 to $35 per ounce potency to turn the trick? Suppose it be assumed that the price of gold will, at worst, not recede, and that the cost of digging ore and treating it of which the average level of commodity prices and wages is a fair index-will, at most, not exceed that prevailing in 1926. One may or may not accept these as reasonable assumptions; but one must arbitrarily remove some of the potential variables if one is to get anywhere on a problem like this. As a matter of fact, this article is not going to venture a conclusive answer to the question that has been posed; but it will endeavor to present some of the factors that have a bearing on the problem. The writer spent ten days visiting a dozen properties in Virginia and the Carolinas early in April, 1935, and in doing so got a first-hand slant on mining conditions in the domain of King Cotton.

Jan 1, 1935

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

Alluvial gold mining in New Zealand and in particular on the West Coast underwent a renaissance during the early 1980's. This was based on two main factors: a) the sharp rise in the gold price b) the advent of the hydraulic excavator with which to mine the auriferous gravels. The scale of operations varies considerably. A small operation typically consisting of one or two people using an excavator to feed either a land based or pontoon mounted (floating) gold recovery unit, which will typically feature a rotary screen with or without a tailings stacker with the screened fines < 10 - 15 mm) fed over riflle tables. The largest screening plants of this type are operated by DML Resources in their Arahura and Mikonui mining operations where the plants have the capacity to screen up to 250 m3 of gravel per hour. These plants usually employ jigs and centrifugal concentrators for gold recovery. Unique amongst current operations is the Grey River Dredge, a bucket ladder dredge capable of processing 700 m3 per hour similar to those that operated earlier this century. Gold concentration is by a series of jigs. The number of plants operating in recent times peaked at around 130 in 1987 (coinciding with a nominal average gold price of $751) and since that time has steadily declined to 80 units in 1993 and about 45 - 50 units today. This cycle of rapid expansion and then steady decline has been repeated on the West Coast since the original gold discoveries in the mid nineteenth century.

Jan 1, 1996

During August, 1926, with the consent of Mr. Schell, mine manager, the writer conducted a mill test on this company's concentrators. Mr. Schell not only gave him his permission, but rendered all possible assistance. Although it was impossible to take all the samples one could have wished to obtain, yet the salient points of the mill flow-sheet were sampled for a continuous period of eight hours, and from these samples and separate data supplied by the manager, valuable information was collected.THE MINEThis is a true vein-type of mine; the lode formations, striking almost due north-south, cut the large porphyritic intrusion at right angles. There are three distinct veins on this property - parallel, persistent, and dipping at an angle varying between 40° - 50° to the horizontal.The country rock is very sound, and timber, save for the small amount required for ore chutes, is entirely absent from all mine workings.The lode varies from a width of 1 in. to 8 in., but the stopes are carried forward with a minimurn width of about 30 in.The mine is particularly dry for a West Coast property, and conditions underground are very favourable. Air drills are used...

Jan 1, 1928

By Kenneth Eltschlager

Business says that location is a primary component of being successful. So too is the importance of location in blasting. For blast seismograph data to be useful, the location of the blast and seismograph must be clearly documented. Another location of importance is that of a nearby structure. Establishing the spatial relationships between the blast, seismograph and nearby structures, allows the blaster to correctly interpret the data, evaluate the performance of the blast and gauge the validity of any complaints.

Jan 1, 2004

By Turker L

The leaching of Tellness (Norway) ilmenite concentrate in hydrochloric acid and mixed aqueous HCl-alcohol solutions at boiling temperatures was investigated. It was found that the alcohols methanol, ethanol and ethylene glycol all substantially increased the leach rate and in the case of methanol and ethanol this was achieved at lower boiling temperatures compared with aqueous HC.

Jan 1, 1986

By D. W. Olson

The estimated value of natural gemstones produced from U.S. deposits during 2004 was $12.9 million. This was a 3-percent increase from that of 2003. U.S. gemstone production included agates, amber, beryl, coral, garnet, jade, jasper, opal, pearl, quartz, sapphire, shell, topaz, tourmaline, turquoise and other gem materials. More than 60 varieties of gemstones have been produced commercially from U.S. mines. But commercial mining of gemstones has never been extensively undertaken in the United States. Most of the deposits have been relatively small compared with other mining operations. In the United States, much of the current gemstone mining is conducted by collectors, gem clubs and hobbyists rather than business organizations.

Jan 1, 2005

Reliable and discriminating small, laboratory scale methods of study have been developed and used successfully in the critical evaluation and interpretation of the carbonization characteristics of a wide range of raw and prepared materials, the variable factors in the coking process, and' the mechanical properties of the carbonized products. The simple and highly economic technologies have been successfully and effectively integrated with detailed surface and subsurface geological exploration programmes (particularly in the coalfields of the .Central Bowen Basin of Queensland) as well as with quality and utilization studies of a nUII!ber of representative Australian and Japanese coals. Previously, only the results of comparatively large, laboratory scale studies have provided information reasonably indicative of those to be anticipated hi industrial practice, but these suffer serious disadvantages in terms of economy of material, time and resources; they have been difficult or even impossible to use as an essential part of any normal or comprehensive exploration programme. On the other hand, although previously developed smaller scale laboratory methods derive considerable advantage from their flexibility, amenity to critical control and inherent potential for speed and economy, they have hitherto permitted no effective or direct comparison with the results of industrial practice or full scale assessment. Comprehensive study results achieved through technologies developed recently at the University 'of Sydney demonstrate that carefully controlled small laboratory scale methods of evaluation quite suitable for use in exploration and, other programmes may be used to predict with considerable accuracy and reliability (in some cases exceedingthat of pilot scale study) the principal strength index of one of the established and internationally recognized full sc:ale tests-the Japanese Industrial-Standard Drum Test. It is probable that further study may establish satisfactory correlations with the results of other standard industrial procedures.

Jan 1, 1969

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By P. Kluge

Mining engineers frequently encounter complex design problems for which the critical components of the design are difficult to quantify or compare. Teams of people typically work on these designs and human perceptions and judgments play a strong role. To assist with this process, the analytical hierarchical process (AHP) as a decisionmaking tool is described in this paper. Although the technique is used in many other disciplines, it is currently not widely used in mining engineering in South Africa. To use the AHP process, the problem should be treated as a hierarchy that defines the goal, the alternatives to reach it, and the criteria for evaluation of these alternatives. Pair wise comparisons are conducted on the criteria of the hierarchy to establish priorities. The value of the technique is that it is simple to test for consistency amongst the pair wise comparisons to ensure that the answer obtained is better than that provided by a random selection. To illustrate the technique, the use of a backfill support system in a platinum mining project was investigated. Ten design parameters, which will be impacted by the use of backfill, were identified and weighted according to their relative importance. The result of the AHP evaluation was that the use of a backfill support system should be preferred to a conventional support system at the mine.

Jan 1, 2011

By J. Hu, F. Lin, R. Chen, F Peng, S. Yang, W. Yu

"Microseismic monitoring technology has become one of the most effective method of mine ground pressure monitoring after decades of development. But safety assessment of mine ground pressure by using microseismic monitoring is still in the development stage, it needs to be perfected continuously in practice, and choose the optimal assessment indexes and methods. The definitions and physical meanings of wave velocity, b value, and EI-VA value are introduced in this paper. Statistical calculation of the microseismic events in Luomu Mine is finished by using these indexes, then the functions and calculation results of V, b value, and EI-VA value with the variable of time are also given in the paper. The preliminary safety assessment method is established in Luomu Mine, and it has achieved good results in practical application.1.1 Engineering background The Luomu Mine is a super large molybdenum and tungsten production base in China, ore reserves is up to 2 billion tons, first in Asia and third in the world. It begins mining since the 1960. and bases on underground mining until 2002. In order to recover resources more effectively, it began to use opencast mining method and formed a production of 30000t/d in the early 1990. After about 30 years of underground mining, a large mined out spaces was formed under open pit mine, up to area of 1.2 million m2 and volume of 18 million m3, as shown in figure 1. The large number of mined out spaces seriously affects the normal production, mining and handling of mined out spaces are in the high risk. In the past years, several rock mass collapsions happened, and it caused a serious security threat to persons and equipments. According to the distribution characteristics of mined out spaces, Luomu Mine is divided into A, B, C, D and E mining area. The stability of D mining area is studied in this article. D mining area mainly includes 1376,1350,1340,1317 mined out spaces and 1280 deep large mined out area, as shown in figure 2. The mined out spaces of D mining area is extremely complex and high-risk. Therefore, a microseismic monitoring system was built to monitor the stability of D mining area, a large number of valuable datum has been obtained, and it has a striking effect (Cheng & Peng, 2013; Peng et al., 2013)."

Jan 1, 2015

By S. M. Jasinski

Peat is a natural organic material of botanical origin. Peatlands are situated predominately in shallow wetland areas of the Northern Hemisphere. Commercial deposits are formed from the gradual decomposition of plant matter under anaerobic conditions for about 5,000-years. In 2004, peat was harvested in 16 states. Florida, Michigan and Minnesota accounted for more than 80 percent of the U.S. production. Reed-sedge was the dominant variety of peat harvested in the United States, comprising almost 80 percent of the output. This was followed by humus, hypnum moss and sphagnum moss.

Jan 1, 2005

By R. B. King

This document was prepared by the DFI International Grouting Committee with the intent to provide a summary of main Standards and Guidelines available for the North America and Europe grouting industry. This document highlights the different approaches, methods and tools used internationally. The DFI International Grouting Committee comprises all parties involved on a grouting project: Owners, regulators, engineers, contractors, and manufacturers (equipment and materials). This document is not intended to cover every conceivable application or requirement of grouting. However, it does provide standard practice requirements for qualifications, materials, equipment, testing, and production procedures for the professional engineer to incorporate into their project specific requirements.

Jan 1, 2021

By NORA Mining Sector Council

The National Occupational Research Agenda (NORA) is a partnership program to stimulate innovative research and workplace interventions. In combination with other initiatives, the products of this program are expected to reduce the occurrence of injuries and illnesses at work. Unveiled in 1996, NORA has become a research framework for the National Institute for Occupational Safety and Health (NIOSH) and the United States. Diverse parties collaborate to identify the most critical issues in workplace safety and health and develop research objectives for addressing those issues. NORA entered its third decade in 2016 with an enhanced structure. The 10 sectors formed for the second decade will continue to prioritize occupational safety and health research by major areas of the U.S. economy. In addition, NORA’s seven cross-sectors will continue to focus on the major health and safety issues affecting the U.S. working population. While NIOSH serves as the steward to move this effort forward, it is truly a national effort. NORA is carried out through councils comprised of members with many diverse interests that are developing and implementing research agendas for the occupational safety and health community over the third decade (2016-2026) of NORA. Councils address objectives through information exchange, partnership building, and enhanced dissemination and implementation of evidenced-based solutions. NORA groups industries into 10 sectors using North American Industry Classification System (NAICS) codes. The Mining Sector encompasses NAICS code grouping 21xxxx where “xxxx” represents the different subcodes of the mining “21” classification. Mining encompasses the extraction of solid mineral and mineral-like substances from their place in the Earth’s crust and supplies them to processing industries that produce economically valuable materials. It does not include oil and gas extraction. The Mine Safety and Health Administration, MSHA separates mining into coal, underground and surface, and metal and nonmetal, underground and surface.

Feb 1, 2024

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By Eugene Nel, Johan Theron, Chris Martin, Hans Raabe

"Impala Platinum Limited is the world’s second largest platinum producer, producing more than 1.7 million ounces of the precious metal last year, much of this from the UG-2 reef located in the Bushveld Complex, South Africa. As part of Impala’s ongoing expansion programme, tonnage through their principal UG-2 processing facility, near Rustenburg, was increased 40% in 2001.To accommodate the increased throughput, the role of the existing primary mills was converted from conventional semi-autogenous grinding units, to attrition and selective grinding units, operating in fully autogenous mode. The finer chromite and coarser silicate components in the mill discharge are then separated by screening and processed in dedicated circuits downstream. This way, the need to spend considerable capital to increase primary grinding capacity was averted.In the last year, considerable work has been conducted to evaluate and optimise the two downstream circuits. This has involved an optimisation programme of sampling and diagnostic flotation testing, supported with QemSCAN analysis. This paper will describe the operation of the new circuit. It will also describe some of the more novel aspects and interesting findings from the optimisation programme.INTRODUCTIONThe South African platinum industry is the world’s largest producer of platinum and the world’s second largest producer of palladium. Located in a wide area north of Johannesburg, the industry mines ores from the Bushveld Complex, one of the world’s great mineral treasure chests, containing over 70 percent of the world’s platinum, as well as extensive reserves of the other PGE (platinum group elements), chrome, manganese and vanadium. The industry employs about 180,000 people in, predominantly, underground mines, which together form an almost unbroken circle of mining operations 200 km in diameter."

Jan 1, 2004

By L. Mead

Dimension stone is a natural stone (granite, marble, limestone, sandstone and slate) that can be quarried, cut and shaped to conform to acceptable industry standards for size, consistency and durability. There are numerous outlets for the finished product in exterior and interior architectural and design applications. A continued growth market is with residential usage— particularly in new, upscale construction. This has become a competitive market between domestic producers and lower cost imported products. These imported products have become available at many of the building supply retail outlets and have increased the use of stone in residential construction and renovation. The traditional architectural application of dimension stone is tied to commercial and institutional building construction trends and market. There has been a noticeable increased usage of stone in the Sun Belt. This stone is usually supplied by local fabricating shops. It is used in the exterior and interior of shopping malls. This market generally uses local stone sources. It has increased the demand for sandstone, limestone and quartzite in this region of the country.

Jan 1, 2005