Search Documents

By C. Acuna

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000?2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A .* R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By Paul S. Korinko, Simona E. Hunyadi Murph

To address a radiological contamination event, a materials and process project was initiated. During the course of this project, processes and materials were developed that successfully captured zinc vapors physically and chemically, respectively. However, the physical traps were placed in an undesirable area and it was determined that the chemically captured zinc reactions was reversible. Consequently, advanced nanomaterials are being developed to capture zinc vapors. The current state of the art of the science and engineering of these materials and their efficacy for zinc capture and retention is discussed in this paper.

Jan 1, 2015

By Wang Yun-yan

In order to examine the adaptability and the kinetics of leaching different gold ores in alkaline thiourea system, six kinds of gold concentrate and/or calcine with different physical and chemical properties were chosen as objects. The leaching behaviors in alkaline thiourea system with high stability, acidic thiourea system and alkaline cyanide system were compared. Changes of phase, surface appearance, particle distribution and specific surface area of six kinds of gold ores before and after leaching were studied in virtue of modern analytic techniques, e.g., XRD, SEM, and so on. The results indicate that alkaline thiourea solution can be used to leach gold ore, for oxidized gold concentrate removed arsenic by microbe pretreatment(4#) the leaching rate of gold is up to 82.68%, such conclusion overthrows the parlance reported that pH value must be less than 1.78, or gold can not dissolve in thiourea solution. Chemical components and phase are related to gold leaching rate, different gold ores are fit for different leaching system, and alkaline thiourea solution is suitable for the pretreated oxidized gold ores with low content of sulfur and in which the main phase was SiO2, phase almost does not change after leaching basically. Generally speaking, when leaching in alkaline thiourea solution, surfaces of gold ores with glaze change greatly to ones with coarseness, distinct trace and holes of corrosion. Particle size decrease and specific surface area increase of gold ores after leaching in alkaline thiourea solution with high stability except gold concentrate of Zhongyuan gold smelter(5#).

Jan 1, 2006

By Jian Li, P. Liu, R. Zhang and J. Lo

In the past decades, focused ion beam (FIB) has evolved into a powerful microscope that provides capabilities that no other microscopes can offer. The combination of high-resolution imaging and stress-free ion beam cross sectioning provides valuable microstructure information both at the specimen surface and beneath. FIB techniques are also the preferred method to prepare site-specific transmission electron microscope (TEM) specimens. CanmetMATERIALS owns a world-class microscopy facility, where advanced microscopy work provides strong supports to research programs that cover a wide range of subject areas. This paper is aimed to provide a few practical examples of FIB applications in microstructure characterizations that include cross-sectioning and imaging, serial sectioning, and advanced TEM specimen preparation in materials research at CanmetMATERIALS.

Jan 1, 2015

By Eun Duck Park

The gold catalyst supported on iron oxide was prepared from gold dissolved in aqua regia by a deposition-precipitation method and applied to CO oxidation in the absence and presence of hydrogen. Some characterization methods such as X-ray diffraction (XRD), nitrogen adsorption, transmission electron microscopy (TEM), temperature programmed reduction (TPR), temperature programmed oxidation (TPO), and the pulsed CO chemisorption with temperature programmed desorption (TPD) were conducted to explain different catalytic activities of Au/Fe2O3 catalyst pretreated at different conditions. The particle size of gold was about 10 nm for Au/Fe2O3 calcined in air at 373 and 573 K. For complete CO oxidation, the decreasing CO conversion with a reaction time was observed at low temperatures but its initial catalytic activity can be restored by a heat treatment at high temperatures. This catalyst was quite active for the selective CO oxidation in the presence of hydrogen especially at low temperatures. In the presence of hydrogen, the deactivation was significantly diminished.

Jan 1, 2006

By E. A. Werner, W. Liebfahrt, J. Blaha

"The influence of the composition and the microstructure on the plane strain fracture toughness of five cold work tool steels all processed via the powder metallurgical route is investigated using 3-point bending specimens. The steels differ in composition and therefore possess different volume fractions of carbides. The amount, size and distribution of the carbides in the matrix are estimated by quantitative image analysis on a plane parallel to the fracture surface without discrimination of the carbide type, since the carbides are always much harder [1,2] than the matrix, irrespective of their composition. Due to the production of the steels via the powder metallurgical route almost all carbides are spherical in shape. The mechanical in-situ properties of the matrix are characterized by indentation tests performed with an ""UltraMicro"" -indenter in a scanning electron microscope.IntroductionCold work tool steels are used as tools in applications where excellent wear resistance and high hardness are required. Examples are cutting, woodworking, thread rolling, wire and deep drawing, cold extrusion and pressing of parts at process temperatures below 200°C. For such applications the steels must show an optimum combination of hardness, wear resistance and toughness while offering good machinability. Hardness and wear resistance are controlled by the amount of carbon and carbide forming elements such as molybdenum, tungsten, vanadium, chromium and niobium. These elements are present in the MC-, M6C and M7C3-carbides and are also responsible for the precepitation of secondary carbides during tempering. In this report attention is paid to the influence of the primary carbides only, while the very small ~~nm) secondary carbides will be treated as constituent of the homogeneous matrix. Increasing the amount of carbides (alloying elements) usually results in a decrease of the material's toughness which is caused by the presence of clusters and/or bands of carbides. To achieve an optimum combination of hardness, wear resistance and toughness many of the today's cold work tool steels are processed via the powder metallurgical (PM) route, which helps to prevent non-uniform element/carbide distribution because of the rapid solidification of the powders used. The resulting microstructure of the tool steel then consists of a tough matrix with uniformly distributed hard carbides· of globular shape. This shape of the carbides is also desirable instead of blocky carbides present in non-PM tool steels, since they improve the machinability of the steel. An additional advantage of PM-steels lies in the possibility to produce near net shaped tools thus lowering the costs of machining."

Jan 1, 2000

By L. J. Lutz

The U.S. Bureau of Mines has developed an electrorefining process to recover Ni, Co, Cr, and other metals from mixed and contaminated superalloy scrap. The superalloy scrap is cleaned then directly electrodeposited as a Ni -Co deposit. The process recovers approximately 90 pct of the Ni-Co available from the scrap as a 99t pct pure Ni-Co alloy. During electrorefining the electrolyte undergoes a purification process which results in Cr and other refractory metals reporting to the purification residue. Operating data is given for a 3-L compartmented electrolytic cell. Techniques for the removal of Fe, Cr, and trace impurities from the recycled electrolyte are outlined. The economics of a facility producing 15 mt/d of a Ni-Co alloy are also discussed.

Jan 1, 1993

By . Menad Gaballah I

Three samples of solid wastes generated by the non ferrous metallurgy were characterized. These residues contain up to 42 % of valuable metal compounds ( Cu, Pb and Zn ) and 23 %of toxic compounds t As, Hg, Cd and Se ). These sample were subjected to thermal treatments between 200 DC and 800 °C in controlled oxidizing. reducing and chlorinating atmospheres. Up to 99 % of As, Cd, Hg and Se were eliminated from these industrial wastes. Cu, Pb, and Zn compounds were concentrated in the treatments' residues of these samples. A Global Decontamination Factor' GDF ' was defined to measure the efficiency of the elimination of toxic elements and the recovery of valuable elements for a specific sample submitted to a given treatment. It seems that the thermal treatment in a reducing atmosphere was the most efficient in decontaminating these solids and the concentration of valuable elements. a.

Jan 1, 1995

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By Zhihong Liu

Monodisperse micron size nickel oxalate particles with rhombohedron morphology were prepared from condensed Ni(OH)2 suspension by a novel gel-sol process proposed by one of the authors. Firstly, condensed nickel hydroxide gel was formed by fast adding 1 mol dm-3 NaOH solution into 0.2 mol dm-3 nickel chloride solution, and then oxalic acid solution with a concentration of 0.25 mol dm-3 was dropped into the gel drop wise through a pump equiped with a pH controller under preset pH value, and in this process, Ni(OH)2 gel was converted gradually into monodisperse nickel oxalate sol. The formation of the nickel oxalate particles was found to proceed through a dissolution-recrystallization mechanism from the nickel hydroxide gel. The product particles exhibited rhombohedron like shape with micron size long axis and sub-micron size short axis. The effects of such factors, as temperature, surfactants, et al, were evaluated experimentally on the particles sizes and morphologies.

Jan 1, 2006

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By Samuel Senanu, Benjamin Agyei-Tuffour, Lifeng Zhang, Eivind Øvrelid, Adegboyega Nathaniel Femi

"The solar grade silicon ingot produced from directional solidification process usually pushes the impurities to the top and finally cut off and discarded, which leads to material loss. The hard inclusions lead to wire breakages during the cutting of the ingot in wafers. The main kinds of inclusions found in solar grade silicon have been investigated using vacuum filtration: needle-like Si3N4 and lumpy SiC inclusions. Clusters of SiC inclusions and Si3N4 are also found. Surface observations of the scraps before polishing reveals that Si3N4 inclusions are usually bigger and in some cases can be about a few millimeters. SiC inclusions are usually smaller, ~200µm but can be ~500µm in some cases. Inclusions observed after filtration are mainly SiC with diameters ~10µm. Through the vacuum filtration, 99% inclusions can be removed 99%. The possible mechanisms of filtration are cake filtration for the larger sized Si3N4 and SiC inclusions and deep-bed filtration the SiC inclusions. For the directional solidified silicon ingot, an approximate distance of ~10mm gave an encouraging cutoff thickness. The inclusions sizes were below 10µm. Introduction The search for an alternative source of energy to fossil fuel has led to a dramatic increase in the demand for solar energy due to its high dependability (abundant in nature) and environmental friendliness 1). During the last 5 to 10 years, the annual worldwide production of solar cell by the photovoltaic industry has increased to an annual rate of 30 to 40 percent 2). A necessary condition for the maintenance and even an increase of this growth rate is a decrease in the cost of feedstock for the solar cell production 1). The total international production in 1997 was 130 MW worth more than $500 million. In 2004 the consolidated world total production of PV cells increased to 1146 MW or around. $7 billion (Figure 1) 3). Silicon is currently the most dominant semiconductor material used in the PV industry. As shown in Figure 2 3), solar cells consist of two types of material, often the p-type and n-type silicon. Light of certain wavelengths are able to ionize the atoms in the silicon (causing atoms to either gain or lose electrons) and the internal field produced by the junction separates some of the positive charges (“holes”) from the negative charges (electrons) within the photovoltaic device. The holes are swept into the positive or p-layer and the electrons are swept into the negative or n-layer. Although these opposite charges are attracted to each other, most of them can only recombine by passing through an external circuit outside the material because of the internal potential energy barrier. Therefore if a circuit is made, power can be produced from the cells under light because the free electrons pass through the load to recombine with the positive holes."

Jan 1, 2008

The kinetics of the oxidation of cyanide by manganese dioxide was studied using a rotation disc electrode system. The rate? of the half-cell reaction of cyanide oxidation is increased at higher hydroxide concentrations. An addition of copper up to 0.001 mole/l was found to enhance the diffusion current, especially at a high hydroxide concentration (0. 1M). A similar enhancement of the reaction rate is also achieved with nickel added at levels up to 0.01 mole/l. Manganese dioxide however requires a i:ow pH to achieve reasonable reduction rates. Leaching studies indicated that the initial reaction rate is strongly dependent on pH, initial concentration of cyanide. Using manganese dioxide cyanide could be oxidized at neutral pH's and ambient temperatures.

Jan 1, 1989

By L. Klinger, T. Werber, LA Levin, A Katsman

"The process of catastrophic carburization known as ""metal dusting"", whereby a solid metallic material is converted into fine particles in a carburizing atmosphere, was analyzed. It was shown that this conversion is the result of plastic deformation and subsequent fracture accompanying diffusional phase formation in the near-surface layer. The process is controlled by internal stresses arising during phase transformation. Competition between stress generation and relaxation may result in the attaining the ultimate strength in the near-surface layer and its fracture. Such a mechanism of metal disintegration may occur in a certain temperature interval depending on the kinetic and geometrical parameters of the system - the diffusivities of the alloy's components, the ratio between specific volumes of the new and the old phases, and the ultimate plastic strain. The temperature interval for disintegration of carbon steel, the rate of disintegration, and the period of the disintegration cycle, were evaluated and compared with experimental data. IntroductionCatastrophic carburization, known as ""metal dusting"", consists in conversion of a solid metallic material into fine particles. The process occurs in a carburizing atmosphere at elevated temperatures. The corrosion product, usually named ""coke"", consists of metallic particles dispersed in a loose carbon matrix. Under industrial conditions metal dusting takes place, for example, in a gas mixture of CO and H2 or in hydrocarbon environments. Steels, nickel- and cobalt alloys are susceptible to this kind of wastage in the temperature range 400-800°.A mechanism of metal dusting in steels was proposed by Hochman [1] and later developed by Grabke and coworkers [2-5]. According to the proposed model, the process consists of the following reaction steps:"

Jan 1, 1996

By Himaki Nakano, Kenji Hara, Toshiaki Tsuru, Shunsuke Kawano, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition of Fe-Ni and Zn-Ni alloys from aqueous solutions is one of the well-known examples of anomalous codeposition in which less noble metal deposits preferentially. In this paper, the electrodeposition behavior of these alloy systems was compared between the methanol and aqueous baths. In Fe-Ni system, the significant suppression of the deposition rate of more noble Ni was observed over a wide range of electrolysis conditions in both methanol and aqueous baths. However, the electrodeposition of Zn-Ni alloys showed the typical feature of normal type codeposition in the methanol baths, which was completely different from that in aqueous sulfate baths. The difference in the electrodeposition mechanism between Fe-Ni and Zn-Ni alloys was discussed on the basis of the alloy deposition behavior in the baths in which the activity of water was varied:INTRODUCTION'It has been well known that Fe-Ni alloys show an excellent soft magnetic property. Therefore, thin films of this alloy have been used to fabricate the'-various magnetic devices. For the production of Fe-Ni thin films, dry processes such as sputtering, PVD and CVD are 'employed frequently and the resulting films showed a preferable property as a magnetic material. Electrolyses as a production technique of thin films, on the other hand, has the advantage over other processes in its cheaper production cost due to the simplicity of the production unit The Zn-iron-group metal alloys such as Zn-Ni and Zn-Fe electrodeposited on a steel sheet ale known to exhibit excellent corrosion resistance and therefore the electrodeposition of these, alloys has been applied to the production of surface treated steel sheets mainly for automotive body panels.According to Brenner (1), the electrodeposition behavior of Fe-Ni and Zn-Ni alloys was' classified into the' 'anomalous type. In this type of codeposition, less noble metal, i.e. Fe for Fe-Ni and Zn for Zn-Ni system, deposits preferentially and the change in -the alloy composition- with the variation of electrolysis conditions was unpredictable because of their obscure deposition mechanism. Since most properties of the alloys mainly depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is neces5al)' to clarify the mechanism of anomalous codepasition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so fur, and among them the hydroxide .suppression mechanism (2), (3) has been regarded most plauslble depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is necessary to clarify the mechanism of anomalous codeposition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so far, and among them the hydroxide suppression mechanism (2), (3) has been regarded most plausible. According to this mechanism, it can be predicted that the codeposition behavior depends greatly on the characteristic of water solvent in this study, using methanol as a solvent, the electrodeposition behavior of the anomalous codeposition was investigated to discuss the validity of the hydroxide suppression mechanism."

Jan 1, 2000

By Zhigan Deng

Cooling crystallization was used to separate iron (III) and nickel (II) from acidic sulfate solution produced by leaching of molybdenum-nickel black shale. The effect of K2SO4 concentration, crystallization temperature, solution pH and crystallization time on recovery of nickel (II) and precipitation of iron (III) was investigated, in order to obtain effective separation of nickel and iron. The optimum parameters determined were as follows: 200 g/L K2SO4, 10 °C crystallization temperature, solution pH of 0.5 and 24 h crystallization. Under these conditions, 97.6% nickel (II) was recovered as K2Ni(SO4)2, 6H2O crystals and only 2.0% of the total iron (III) was precipitated. Recrystallization yielded K2Ni(SO4)2, 6H2O crystals with a purity of 98.4%.

By M. J. Walker

The lead .smelter at Cominco's operations at Trail, B.C. has been undergoing. a modernization program since 1986. In that year a contract agreement was reached with German-based Lurgi GmbH which allows Cominco to construct and operate a lead smelter using Lurgi's QSL process. Cominco Engineering Services Ltd. (CESL), a subsidiary of Cominco Ltd., was contracted to provide project management, engineering, procurement and construction management? services for the project. The new smelter replaces the existing sinter-blast furnace plant ?and will have a capacity of up to 1601000 tonnes per year of refined lead. This new smelting proc.ess results in significant operating cost reductions and major environmental .improvements. Start-up of the new plant is scheduled for the fall of 1989. The metallurgy and the operating parameters, important to the design of the new smelter, are described together with projected deportments of lead, zinc, silver and minor metals. A plant description, will be given for the following major areas that make up the modernization project: the pressure filter operation for the preparation of ,zinc leach residues feed material, the QSL reactor and boiler itself, together with its feed system and process gas treatment, and the drossing plant with a new continuous drossing furnace and oxygen softening and thallium removal. Slag from the QSL reactor will be treated in existing slag furnaces until a subsequent second phase of the modernization is completed in the 1990s.

Jan 1, 1990

By T. H. Jeffers

The U.S. Bureau of Mines' Salt Lake City Research Center. has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants? from wastewater&. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high .affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics . and can be used in conventional processing equipment or low-maintenance systems.. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine wastewater& using B'IO"FIX beads. Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NDIJS) after 175 loading-elution cycles, Adsorbed metals were removed from the beads using dilute ?mineral .acids. In many cases" the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge. Tests indicated that use of the beads in a low-maintenance system was particularly effective for treating remote acid mine drainage waters? and small toxic seeps from hardrock mining districts ..

Jan 1, 1991

By Bradford H. Miller

Separation and Recovery Systems, Inc. (SRS) provides on-site waste minimization and resource recovery using its state-of-the-art MX-1500 centrifuge and MX-2000 thermal desorber. The MX-1500 can process over 450 feed tons of material per day, resulting in centrifuged cake containing 20% to 60% by weight. The MX-2000 is a hollow-flite thermal processor indirectly heated by either steam or hot oil. SRS has dewatered and/or deoiled over 1,000,000 feed tons of material in the refining, chemical, and energy industries using the MX-1500. SRS estimates that over 300,000 barrels of reusable oil have been recovered from that material. Additionally, SRS has dried and/or detoxified over 150,000 wet tons of solids or soil to regulatory or customer-specified limits using the MX-2000.

Jan 1, 1994

By O. Morfín

The most probable source of Pb contamination in the perennial reach of Aravaipa Creek, Arizona, has been determined using Pb isotope ratios and total metals analyses of samples collected from the ephemeral and perennial reaches and mine wastes located in the Aravaipa Mining District . Previously, elevated levels of Pb, Cd and As in fish in the perennial reach of Aravaipa Creek, a protected wilderness area,, were assumed to be due to off-site transport from abandoned flotation tailings piles located at Klondyke, Arizona upstream of the wilderness area.Our work replaces this inference with isotopic data that allows us to confirm this hypothesis. The Pb/Zn deposits of the district were mined between the late 1890s and the late1960s, with the most significant ore production coming from one deposit in a rhyolite dike swarm on the Western front of the Santa Teresa Mountains, a granitic pluton of Cretaceous-Tertiary age (~65 ma). Mineralogy has been well constrained across the length of the lode system: Pb and Zn sulfides predominate in the NW sector, and a mixed suite of hypogene/supergene Pb sulfide and Pb oxide minerals comprises the majority of its SE corner. Total metals analyses and comparison of metals ratios serve to constrain the source and transport of certain metals within different parts of the system. Pb isotope ratios in samples, obtained by ICP-MS analysis, define two distinct contributors. The first end-member (208Pb/204Pb = 38.513 to 38.721 and 207Pb/204Pb= 15.550 to 15.598) is characteristic of the mixed, oxide/sulfide ores at the SE end of the deposit. A second end-member (208Pb/204Pb = 38.855 to 38.946 and 207Pb/204Pb = 15.610 to 15.625) characterizes samples taken from the NW, purely Pb sulfide end of the lode. Pb isotope ratios from perennial reach sediments are closely correlated with ratios given by samples from the Klondyke tailings site and by Pb sulfide samples from the NW sector, the primary source of ores processed at Klondyke.

Jan 1, 2003