Search Documents

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000

By E. Oshilna

The Mitsubishi process has many advantages pertaining to economical and environmental matters. These advantages have led to the installations of the Mitsubishi process in constructing new smelters: The Mitsubishi process utilizes highly oxygen enriched blast air and uses a special lime slag in the C?furnace. These characteristics change the . distribution of Impurities from other processes which use P.S. converters, Recently an Increased amount of secondary materials which contain impurities Is being treated at Naoshima Smelter. In order to cope with an Increment of the Impurities load and maintain the cathode quality, many Improvements have been Implemented. This paper discusses the impurities behavior In the Mitsubishi process and describes the measures taken to treat an Increased ?amount of secondary materials:

Jan 1, 1998

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012

By Catherine Cai

A granular sorbent, prepared by gel-coating polyethyleneimine (PEI) on high surface area silica followed by crosslinking with a low-molecular weight diepoxide, has significantly higher uranium capacity, greater salt tolerance, and faster kinetics than the commercial resin Dowex 21K. Though having lower U(VI)/Fe(III) selectivity than Dowex 21K, the gel-coated PEI affords much higher sorptions of both U(VI) and Fe(III) and also their separation by selective stripping with acid.

Jan 1, 1999

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Patrice Chartrand, Halvor Dalaker, Philippe Ouzilleau

A size-dependant thermodynamical model for the carbon-hydrogen previously developed by Ouzilleau et al. [1] has been expanded here to include chemisorption of methyl groups. Gibbsenergy minimalisation calculations using FACTSAGE software on this model indicates that hydrogen bonding through methyl groups is energetically favoured as an intermediate between bonding as monoatomic hydrogen to edge hexagons (which is more favourable) and as monoatomic hydrogen to corner hexagons (which is less favourable). The model has also been applied to methane decomposition and oxide reduction using natural gas. A C-H solid solution as a thermodynamic description of the solid carbon phase influences calculations of carbon activity in metastable methane, and gives different results than when using graphite.

Jan 1, 2015

By Eiji Iwamura

"Two types of diamond-like carbon (DLC) films with different microstructures were prepared by unbalanced magnetron sputtering, and the tribological properties of the nanoscaled DLC multilayer coatings consisting of alternating layers of graphitelike and amorphous-like microstructures were examined. The DLC microstructure was characterized by certain features of graphite-like clusters, in that some of them had onion-like structures. The films filled with the clusters were obtained in a condition with an incidence of high influx of energetic electrons, and the other films without apparent cluster structures were formed in a condition with ion bombardment controlled by negative bias voltage applied to substrates. Stacking each film layer-by-layer, the nanoscaled multilayered coatings showed superior tribological properties to individual single-layered films due to the combination of properties induced by the difference of microstructures.IntroductionIn various tribologiql applications, it is necessary for diamond like carbon (DLC) coatings to have adequate adhesion, significant hardness and a concomitant low friction coefficient. A number of deposition techniques and coating structures have been proposed to achieve suitable DLC properties [1-3]. However it is still difficult to obtain a satisfactory level of combination of the properties particularly desirable for engineering applications.In this study, the features of unbalanced magnetron sputtering were demonstrated with the effect of ion and electron bombardment. Two types of microstructures , namely amorphous-like and graphite-like, were prepared by changing the condition of the charged particles bombardment during deposition. Using the difference of properties induced by the microstructures, nanoscaled DLC multilayered structures were examined in an attempt to improve tribological properties."

Jan 1, 2000

By Randall M. Gennan

Generally sintering is focused on the bonding of particles at high temperatures; possibly with simultaneous densification. However, an important aspect of sintering occurs during heating at relatively low temperatures where polymer processing aids are removed via control of the atmosphere, heating rate, or hold time at intennediate temperatures. New insights into burnout processes show impact from the polymenype, particle size, amount of polymer, atmosphere, part geometry, and thermal profile. This presentation focuses on the key parameters to demonstrate improved mechanical property levels are available in traditional powder metallurgy alloys by proper selection of the processing polymer and proper care in its thermal extraction. The focus is on mechanical property, where gains up to 40% are demonstrated due 10 changes in the processing polymer. Further, atmosphere control during polymer burnout provides a benefit by allowing formation of desirable carbonitrides, giving strength levels over 3 GPa (over 400 kpsi). Insight is? gleaned from powder injection molding, where high polymer contents mandate proper processing control.

Jan 1, 1996

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By Toshitaka Ota, Hisao Suzuki, Minoru Takahashi

"Perovskite-type lead zinc niobate (PZN) exhibits excellent electrical properties such as high dielectric constant, high electrostrictive coefficient and superior piezoelectricity. Therefore, PZN ceramics are very promising for high performance electronic devices. However, perovskite phase PZN is not stable under the ambient atmosphere. Accordingly, it is very difficult to prepare single-phase perovskite PZN ceramics. In this study, A-site cation of lead was partially substituted for barium to stabilize the perovskite phase of the PZN (Ba-doped PZN) powder. In addition, molecular design of an alkoxide precursor was controlled for a low-temperature processing. As a result, molecular design to suppress the lead-volatilization during calcination was preferred for a low-temperature processing. Processing temperature for a single-phase perovskite was depended on the amount of barium dopant. Doping of20 mole% of barium resulted in the single phase perovskite at 900 °C. The temperature for the single phase perovskite of Ba-doped PZN powder, which depended upon the amount of Ba-doping, was lower than that of the powder prepared by the atmosphere controlled conventional powder processing at least by 150 °C.IntroductionFerroelectric thin films and powders with perovskite structure are of renewed interest for micro-electronic applications, including ferroelectric random access memory (FRAM), dynamic random access memory (DRAM), and thin-layer capacitors integrated onto a silicon wafer [1-3]. In addition, recent advancement in micro-machine requires a high performance micro-actuator [4]. A perovskite type relaxor of Pb(Zn113 Nb213)03 is one of the promising materials for a high performance capacitor and microactuator because of their high permittivity and electrostrictive coefficient [5]. Therefore, this paper focuses on the low temperature processing of Ba-doped PZN powders.Chemical solution deposition (CSD) from molecular-designed alkoxide precursor solution is one of the most promising techniques for processing high-performance powders and thin films because it offers precise control of compositions on a molecular scale as well as a low processing temperature [6]. However, chemical solution deposition of perovskite type PZN powders and ceramics are very difficult because of the formation of stable pyrochlore phases. Therefore in the past, PZN powders and single crystal have been prepared by the hydrothermal method or flux method as well as the partial substitution method of a A-site cation [7-10]. In this study, a suitable molecular design for a preparation of perovskite type Ba-doped PZN powders with a chemical solution deposition process is investigated as well as the effect of A-site cation substitution. Chemical solution deposition from molecular-designed alkoxide precursor solution is expected to decrease the amount of a A-site substitution and/or a crystallization temperature for a single phase perovskite. This paper describes ""the relation between molecular-design and processing temperatures for a single-phase perovskite of Ba-doped PZN powders in comparison with the conventional oxides mixing method."

Jan 1, 2000

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Carbonaceous refractory materials are widely accepted in many reducing smelting processes such as iron and ferroalloys. Oxidizing processes such as copper concentrate smelting traditionally use magnesia and/or alumina/silica refractory materials. The main objection to the use of carbon-based refractories as the exposed working lining in oxidizing applications is the potential for free oxygen to react with the carbon at high temperature, which could rapidly degrade the refractory lining. In 2013, Outotec and GrafTech conducted joint trials of a thermally conductive, carbonaceous lining for smelting copper concentrates in the Outotec® pilot-scale top-submerged-lance (TSL) furnace in Dandenong, Australia. This testwork had two equally important goals; to demonstrate the ability of carbon refractories to withstand oxidizing process conditions, while ensuring that neither furnace operating conditions nor process stability were negatively affected by the refractory material. The paper discusses the input parameters of the trials, key observations during the testwork program, and the results and conclusions from both process and refractory design standpoints.

Jan 1, 2016

By B. R. Baldock

The converting of high-grade nickel matte for production of low-sulphur matte or nickel metal is a process which has eluded metallurgists in the past because of the limitations of conventional converting furnaces. The high temperatures required and the refractory nature of nickel oxide has prevented practical success in a process which has been known to be theoretically feasible for a long time. The Ausmelt top submerged lancing system is capable of operating under close control of the smelting conditions. High temperatures and both rapid oxidation and rapid reduction can be achieved. These features have provided the basis for successful pilot plant trials of the desulphurisation of high-grade matte from the Kalgoorlie Nickel Smelter. Sulphur level in product was lowered from 20 to 25% to as low as 0.2%, with iron levels in matte in the range of 1.0 to 3.5%. The theoretical background of matte desulphurisation is surveyed and the pilot plant operations described. The implications of the results in relation to commercial plants and possible refinery operations are summarised.

Jan 1, 1993

By Hai-Xing Fang, Bing Xie, Hong-Yi Li

"In the duplex melting process, chromium forms chromium spinels, the study of which will help to exploit the Hongge ores (rich in chromium) in the Panzhihua-Xichang area in China. Mimicked chromium slag was synthesized. The oxidation and decomposition mechanism of the Fe-Cr spinels contained was studied in a sodium roasting process. The effects of temperature, roasting time, amount of soda added and filling reagents were investigated. The leaching-reduction-precipitation-calcination procedure to extract Cr2CO3 was optimized. The results showed that the optimized roasting temperature was 1000~1020°C with a stoichiometric Na2CO3 addition and without any filling reagents. Roasted materials were leached with distilled water and were filtered to obtain a chromium-containing solution, which was adjusted to pH 1.60-1.80. A reducing reagent, NaHSO3, was added in a stoichiometric ratio and the solution was then adjusted to pH 7.25~8.25. Maximum Cr2O3 precipitation was obtained and the precipitate was calcined at 1050°C for 2h to obtain Cr2Ü3 with recovery rate over 96%.IntroductionChromium is widely applied in the metallurgical industry, in refractory materials and in the chemical industry with its particular properties of hardness, wear-resistance, high temperature resistance and corrosion resistance [1]. There is no free state of chromium in nature and chromite is the main chromium containing mineral [2], China is poor in chromium resources, despite its large demand, and there are few deposits of high grade of chromite ores except in some regions in Tibet and Xinjiang province [1, 4]. Hongge, one of largest titanomagnetite mines in Panzhihua-Xichang area, is a polymetallic deposit mainly containing iron and titanium; it is also associated with various beneficial elements such as chromium, copper, nickel, etc. [3]. As investigated in Reference 3, the chromium reserves of Hongge ores are so large that it is of great importance to study how to extract the chromium from them."

Jan 1, 2012

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control. The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b)process chemistry c )discharge options and recovery of treated water and d) sludge disposal. The long term goal of any smelter and/or refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By Knut H. Bech, Stein Tore Johansen

"The collision efficiency for small particles relative to 2D spherical bubbles in a developed turbulent flow field were calculated applying an adopted version of the CPD program FLUENT. The turbulence field was related to bubble size and fluid properties. The results were compared with analytical theory. The turbulence intensity was found to be the most important single parameter for collision efficiency. Effects of boundary layer thickness and particle diameter were discussed. IntroductionRemoval of inclusion particles from melted aluminium can be facilitated by means of a rotor system that supplies kinetic energy and gas bubbles to the floating metal. At the surface the inclusions adhere to the surface dross or slagg which is removed at regular intervals by the operators. When applying computational fluid dynamics (CFD) to model such a system, one experiences difficulties with the large range of turbulent length-scales encountered, from the large geometrical scales of the rotor and container, through the bubble size and down to the particle diameter. A mathematical model for the complete system will be both complex and require an extreme spatial resolution. Another way of dealing with the problem is to model the micro-scale phenomena separately and apply the results to create a model for the macroscopic system. In a previous work [12] we addressed these problems and developed a procedure for calculating turbulence enhanced flotation to bubbles. It was found that turbulence may have a profound effect on the collision rate of particles to idealized bubbles. In this study we recognize that only a fraction of the total turbulent kinetic energy generated by the rotor's work on the liquid metal may contribute to enhanced flotation. By using a model spectrum for the turbulence, the fraction of turbulent energy in eddies smaller than the bubble diameter is calculated. A twodimensional CFD model was then constructed to calculate the collision efficiency between particles and bubbles of various sizes."

Jan 1, 1999

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b )process chemistry c)discharge options and recovery of treated water and d) sludge disposal The long term goal of any smelter and/lor refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By M. Yoshida, S. Hanada, T. Takasugi

"A study has been conducted to examine the effect of ternary alloying elements on high temperature deformation of the C15 NbCr2 based intermetallics in Nb-Cr-X (X=V, Mo and W) alloy systems, which have attractive properties as high temperature structural materials. The high temperature deformation of the C15 NbCr2 intermetallics can be improved by two alloying methods. One method is based on geometrical consideration for site occupation and atomic size factor of component elements and additive elements in the single phase C15 lattice; addition of Mo and V can promote dislocation movement without introducing significant hardening. The other method is based on microstructural modification through ternary alloying; moderate addition of these elements results in a variety of duplex microstructure consisting of the C15 phase and bee solid solution without forming any intermediate phases, and can enhance the high temperature deformability. Particularly, alloys with duplex microstructure equilibrating with Cr-rich bee solid solution is shown to exhibit superior deform ability. Also, lattice property of the additive atoms in the C15 structure and phase relation between the C15 structure and the bee solid solution are investigated by OM, XRD, TEM and ALCHEMI observations and then discussed in association with observed mechanical behavior.IntroductionLaves intermetallics with AB2 stoichiometry belong to the largest group in a large number of intermetallics with various kind of crystal structures, and have a variation of the cubic CIS, the hexagonal C14 and the dihexagonal C36 structures, depending on stacking sequence of XYZ type, each of which consists of four interpenetrating atomic layers (1-3). Some of the Laves intermetallics have good functional properties and therefore are considered to be used as, for instance, magnetic materials, magneto-optical materials, hydrogen storage materials and superconducting materials (2). Also, the Laves intermetallics are considered to be good candidate as high temperature structural materials operating at high temperatures and in severe environment because they have high melting point, low density, and potential resistance to corrosion and oxidation. However, the Laves intermetallics are very brittle at low temperatures because they consist of complex crystal structures similar to many other intermetallics."

Jan 1, 1996

By Hongbo Zhu, Jinhui Peng, Linqing Dai

"To optimize the process variables for making direct reduced iron (DRI) by microwave heating, the reduction temperature, reduction time and the ratio of coal to material were studied with the central composite design (CCD) and their interactions on the Metallization rate were also investigated. The predictive polynomial quadratic equations model was analyzed by ANOVA. Optimal conditions of making DRI can be concluded as follows: 28 min at 1139?, the ratio of coal to material is 20.95%. Under these conditions, the metallization rate is up to 97.06%.1. IntroductionThere are some technical problems in making direct reduced iron (DRI) or sponge iron using iron ore concentrates containing coal and lime. In reduction of the iron ore concentrates containing coal with microwave heating, the strength of pellets needn’t to be considered. It reduces the costs and improve quality of materials, but also eliminates the need for pellet preparation process, simplifying the process and achieving a cleaner production.Microwave energy is a clean energy, and has characteristic of selective heating. The speed of heating is also fast. It researched by Chen Jin that when the mole mass of C: O is 0.627 and the microwave power is 15KW, it only spends 15min from 15? to 1021.6? with 1 kg iron ore containing coal with microwave heating [1]. There are many factors affecting metallization rate. In order to find a suitable condition for reduction process, it is necessary to design a series of suitable experiments.Response surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [2–5]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the identification of the vital controllable factors to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected. The process optimization of the microwave reduced iron ore was seldom reported in literature. Hence the present work intends to assess the effects of variables such as reduction time, reduction temperature and the ratio of coal to identify the optimum conditions using a central composite design (CCD). The characteristic of product was assessed using scanning electron microscope (SEM)."

Jan 1, 2011