Search Documents

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By J. D. Law

The presence of long-lived radionuclides presents a challenge to the management of radioactive wastes. Separation of the radionuclides from the waste solutions has the potential of significantly decreasing the costs associated with the immobilization and disposal of the waste by minimizing waste volumes. Several solvent extraction processes have been developed at the Idaho National Engineering and Environmental Laboratory for the separation of transuranic elements (TRUs), 90 Sr, and/or 137 Cs from acidic radioactive waste solutions. The TRUEX and POR processes for the separation of TRUs, the SREX process for the separation of 90Sr, the cobalt dicarbollide process for the separation of 137Cs and and a universal solvent extraction process for the simultaneous separation of TRUs, 90Sr, and 137Cs have all been developed in centrifugal contactors using actual liquid radioactive waste solutions and simulated dissolved calcine waste solution. In addition, the behavior of metals with each of the solvent extraction processes was evaluated. This article summarizes the most recent results of the each of the flowsheet demonstrations and provides Information on the centrifugal contactor equipment used for the testing.

Jan 1, 1999

By Shengli Wu, Fengjie Zhang, Feng Chang, Hua Lu, Kaiping Du

In order to make a complete understanding of steel plant metallurgical dusts and to realize the goal of zero-waste, a study of their properties was undertaken. For these purposes, samples of two sintering dusts (SD), two blast furnace dusts (BFD), and one electric arc furnace dust (EAFD) taken from the regular production process were subjected to a series of tests. The tests were carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy via SEM (EDS), and Fourier transform infrared spectroscopy (FTIR). The dominant elements having an advantage of reuse are Fe, K, Cl, Zn, C. The dominant mineralogical phases identified in sintering dust are KCl, Fe2O3, CaCO3, CaMg(CO3)2, NaCl, SiO2. Mineralogical phases exist in blast furnace dust are Fe2O3, Fe3O4, with small amount of KCl and kaolinite coexist. While in electric arc furnace dust, Fe3O4, ZnFe2O4, CaCO3, CaO, Ca(OH)2 are detected.

Jan 1, 2015

By Musa Karakus

In an attempt to explain the phenomena of lead entrainment during Cu drossing of lead bullion, two different synthetic lead bullions were heated to 1050°C, cooled slowly to various temperatures, and then quenched. The morphology and composition of dross particles that form when Mn is used to desulphurize bullion also were examined. Polished sections of these pyrometallurgical products were examined by process mineralogical techniques to identify the impurity phases, determine their chemical compositions, examine the morphology of the impurity phases and evaluate the potential for lead entrainment in such crystals, and characterize pre-quench and quench-generated phases. The phases crystallized were metallic lead, metallic copper, galena, chalcocite, albandite, Cu14.4Pb2S9. and 5.5Pb2S3.5. Metallic copper formed isometric skeletal crystals, chalcocite formed platy and skeletal crystals, and 1formed crystals and eutectic intergrowth with chalcocite and Cu14.4Pb2S9 or Cu5.5Ph2S3.5. The pre-quench crystals are larger and usually exhibit skeletal forms; the quench-generated phases are only a few micrometers across and disseminated throughout the lead matrix. Skeletal crystals of metallic copper and chalcocite form three dimensional networks that entrain large amounts of metallic lead.

Jan 1, 1989

By Senlin Xie, Wanlin Wang, Lejun Zhou

"The innovative development of multiphase slag in hot-metal treatment has attracted considerable attention due to the reduction of CaO consumption and minimal environmental emission. In order to improve the efficiency of dephosphorization and to reutilize the waste-slag as an alternative source of phosphate ores, it is important to increase the distribution ratio of P2Os between the solid solution (2CaO· SiO2-3CaO· P2O 5) and liquid slag. An investigation was carried out to study the effects ofNa2O and B2O3 on the distribution ratio of P2Os, the results indicated that the increase ofNa2O would enhance the distribution ratio of P2Os with the formation of solid solution (2CaO·SiO2-Na2O·2CaO·P2Os), while B2O3 has the opposite function, and changes the morphology of solid solution. The study would provide an instructive way for the design of multiphase slag and re-utilization of waste-slag.IntroductionIn order to meet the increasing demand for high quality low-phosphorus steel, it requires a high efficient hot metal dephosphorization process. The current slag system for hot metal treatment contains large amount of solid CaO dispersed in liquid slag, which introduced a large amount of CaO consumption due to its low solubility, especially when CaF2 was restricted due to the environmental concerns. Therefore, new refming method to improve the utilization efficiency of CaO by using a solid/liquid coexisting multiphase slag was proposed, and the studies regarding to solid solution formation mechanism, mass transfer behavior of phosphorus and the phase relationship for multi-phase slag have been conducted. [1-6]Normally, hot metal dephosphorization slag consists of CaO--SiOz-FeO--P2O 5, and it has been approved that 2CaO·SiO2 forms a solid solution with 3CaO·P2Os at the hot metal treatment temperature over a wide range of compositions. [7] Kitamura et al [8] pointed out that the (2CaO·SiO2-3CaO·P2O 5) solid solution plays an important role in dephosphorization, and it has been regarded as an absorbents for phosphorus to lower the phosphorus content in liquid phase, which makes it more capable for future dephosphorization. l Besides, the multiphase slag has the potential to be recycled as a source of phosphorus, if the (2CaO· SiO2-3CaO· P2O 5) solid solution could contain high phosphorus content, and it can be separated from FeiO matrix 8hase due to the large difference of their magnetic properties under the strong magnetic field. [10, 11]"

Jan 1, 2014

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By Jonkion M. Font, Ramana G. Reddy

A thermodynamic model for a priori predictions of arsenic and antimony impurity capacity in Ni-Cu mattes and slags was developed based on the Reddy-Blander (RB) capacity model. The As and Sb capacities were calculated a-priori considering the RB capacity model in Ni-Cu mattes and FeO-FeO1.5-MgO-CuO0.5-NiO-SiO2 slag at 1573 K and 0.1 to 1 atm partial pressure of SO2. The results showed an excellent agreement between the model calculated and experimental data of arsenic and antimony capacities between the mattes and slag. The impurity capacity model developed here, can be extended for prediction of impurity capacities in multi-component base metal slags and base metal mattes. Such a priori predictions of impurity capacities can lead to develop or improve the efficiency of impurity removal from the base metal smelting, converting and refining processes.

Jan 1, 2014

By W. G. Davenport

This chapter shows how flash furnace industrial oxygen and oil requirements are affected by different: (a) product temperatures (b) conductive, convective and radiative heat losses (c) electrical energy inputs (d) hydrocarbon fuels. The calculations of the chapter are all for production of 65% Cu matte from pure CuFeS2 concentrate. Blast temperature is? 298 K throughout.

Jan 1, 2001

By Derek J. Fray

"A need exists for fast and accurate analysis of species in various phases at elevated temperatures. Although modern analytical techniques are very efficient, the equipment is usually situated some distance from the industrial operation and time is spent taking the sample and sending it to the analytical facility. Several minutes can easily lapse and, during this time, heat must be supplied in order to keep the system molten and, if the composition is changing rapidly due to a refining process or reaction with the environment, the information may only be of retrospective use. Perhaps more important reasons for the use of on-line sensors are that instantaneous analysis gives better control, process optimisation and the minimisation of energy losses and pollution. To date oxygen has been the only element which is measured widely using solid electrolytes. However, the analysis of many more elements is required and possible electrolytes for other species are discussed. For some elements, ~here is no suitable conducting electrolyte and, therefore, a different approach is adopted where the electrolyte, in which one species is mobile, comes to equilibrium with another species. IntroductionThere is an ever increasing demand for the development of sensors for on-line measurements in most areas of technology and, in particular, metal processing. This is especially relevant in situations where greater control can be achieved by monitoring the chemical composition of the melt during processing and where a minor constituent in the melt can have a major effect on the properties of the finished alloy. Although modern analytical techniques are fast and reliable, the equipment due to its complexity, is frequently situated away from the process area and valuable time may be spent in sampling and transportation. During this period, heat may have to be supplied to prevent solidification and the refining reactions may be continuing, and, therefore, the analytical information may not be of direct use."

Jan 1, 1988

By T. Kimura, H. Ohba

"Much effort has been made to reduce the energy requirement in zinc electrowinning. In order to keep energy consumption low, either to make cell voltage low or current .efficiency high is necessary. Decrease of cell voltage practically depends on how to reduce ohmic resistance in the electrolyte and the anode crust. To realize these, new concept was proposed and the pilot plant has been operated. The space between a cathode and an anode is halved by utilizing the frame insulator. With these frames the anodes and cathodes compose of a unit of electrodes, and this unit is handled by newly designed electrode handling machine (E.H.M.). The process includes lifting up electrodes, expanding the space between a cathode and an anode, cleaning them, stripping the deposited zinc and returning the unit to the cell. As a result, cell voltage is kept as low as calculated and predictable energy reduction has been achieved. IntroductionIn the recent trend of a rapid appreciation of the Japanese yen, Akita Zinc Refinery of Mitsubishi Metal Corporation has been confronted by problems of relatively high operating costs. In order to compete with other overseas zinc refineries, it is necessary to reduce the cost of zinc production, especially the cost of electric power which now accounts for .up to 35 % of the entire cost of production. Three fourth of the electric power used at Akita Zinc Refinery is for the electrolysis. Therefore it is extremely important to reduce the cost of electrolysis.There are two possible measures for solving the problem; one is to use more nighttime electricity taking the advantage of its inexpensive power price, and the other is to reduce electric power consumption.As a part of a rationalization plan carried out in 1986, Akita Zinc Refinery increased the number of operating cells. As a result, when nighttime electricity is used, the silicone rectifier has been able to operate at full capacity. Moreover, by new schemes of ""increase of area for electrodeposition by ralslng the liquid level of electrolyte"" and ""increase of the number of electrodes in each cell"", current density could be lowered and as a result, the electric power consumption has been improved. In order to raise nighttime ratio even higher, installation of an additional rectifier and cells would be required."

Jan 1, 1988

By William Petruk

A mineralogical and image analysis study was conducted on samples of U tailings from pilot-plant runs on Midwest ore in Northern Saskatchewan. The tailings had been subjected to simulated weathering for the equivalent of 10 years in a tailings facility (lysimeter). The pH varied from 7.0 at the beginning of the test to 5.9 at the end. The results show that during the simulated weathering sane of the gersdorffite, uraninite, galena and pyrite had oxidized, with gersdorffite being the most reactive and pyrite the least. Reaction was evident at the top of the lysilleter , but was most intense at the seepage discharge. sane of the released ions precipitated as Ni, Pb, and U arsenates, sulfarsenates, sulfates and oxides on particles of all minerals. Green crystals of Ni sulfate and white crystals of ca sulfate had precipitated at the surface of the lysilleter. Clay minerals and chlorite had washed from the top of the lysirneter towards the seepage discharge.

Jan 1, 1989

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013

By Jayagopal Uchil, M. Krishna, Shanta Sastcy

"Damping behaviour of aluminite particulate reinforced ZA-27 alloy metal matrix composites processed by compocasting method is studied. The weight percentage of particulate reinforcement is 0,1,2,3, and 4%. A dynamic mechanical· analyzer is used ·to measure the damping capacity and dynamic modulus at the natural frequency of the specimen over a temperature range of 30°C to 300 °C both in the heating and cooling cycle. The damping capacity of the material is found to increase with increase in temperature and weight percentage of aluminite reinforcement although this is accompanied by a decrease in dyliamic modulus.The damping capacity and dynamic young's modulus exhibit a sharp decrease in their values around 300 °C a8 ZA-27 alloy undergoes a first order phase transition in this region which is confirmed by Differential scanning calorimetric studies. Several damping mechanisms have been evaluated theoretically for the material under study. The damping capacity at low temperatures is attributed primarily to coefficient of thermal expansion mismatch induced dislocations and high intrinsic damping of the matrix. At higher temperatures the damping capacity is attributed to ZA-27/aluminite interface, phase transformations and thermoelastic damping.IntroductionMetal matrix composites. (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and lightweight [1-5]. At present, the usage of ceramic particles as reinforcement in MMCs has attracted considerable interest from scientists and engineers. The MMCs show substantially improved elastic modulus, strength, stiffiless, and tribological properties with low coefficient of thermal expansion compared with the unreinforced matrix material."

Jan 1, 2000

By Arsenio Enriquez, Adrian Deneys

"Rio Tinto through its subsidiary Kennecott Utah Copper Corporation (KUC) and Praxair have implemented the CoJet® gas injection system for copper anode refining. The system provides the capability to melt on average 60 to 70 tons of scrap copper per heat (with acceptable NOx emissions). The system has demonstrated the potential for tuyere-less sulfur and oxygen removal using coherent jet technology.This paper describes the process concept, system development, laboratory testing, implementation, current operation and ongoing developments."

Jan 1, 2009

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By J. W. Perez

Raw coal will often break intragranularly in either a completely random way or in a differential mode where one species will have a different rate of breakage than another. Locked coal-ash and coal-pyrite particles can also break by the preferential detachment of one species from another along zones of inherent weakness in locked particle assemblages. The mode. cf breakage is largely a function of the nature of the feed, but it is also influenced by the comminution device and the operating variables. Evidence of breakage of particles in the various modes is seen in the crushing of raw coal and middlings particles with a rotary beaker, jaw crusher, rolls, hammer mill and rod mill. Evidence from the literature indicates the detachment mode is often important for coal, ores and metallurgical products. Further confirmation comes from the crushing of a specially prepared 'ore' of sized magnetite in plaster of Paris.

Jan 1, 1988

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By George E. Cook, Peter C. Levick, Francis M. Wells

"Relationships are established between the peak current of a pulsed, rectangular current waveform and the pulse current duty cycle under conditions of constant arc power. By appropriate choice of these interrelated parameters, it is shown that the arc pressure may be varied over a wide range even though the arc power is held constant. The methodology is suggested as a means of countering the effect of gravity in 5-G welding, while maintaining constant heat input to the weld. Combined with appropriate penetration sensors, the methodology is additionally suggested as a means of controlling penetration. IntroductionBoth low frequency pulsation (typically 0.1 - 20 Hz) and high frequency pulsation (> 100 Hz) are often used with GTA welding. Benefits derived from pulsing include improved weld quality and better process control.Advantages cited for low frequency pulsation include claims that the total heat input to the weld is reduced, the weld bead size is reduced, weld penetration is increased, grain size is reduced, porosity is reduced, weld distortion is reduced, thinner materials can be welded successfully, and the tolerance of the welding process to material and production variations is improved (1-16). With respect to the latter, pulsing aids control of weld bead penetration by increasing the tolerance to component dimensions and joint fit-up. It also reduces the sensitivity to disparities in heat sink, and it helps to reduce distortion in thin section material or distortion attributable to poor clamping. In certain materials it can reduce the sensitivity to surface oxides and to cast to cast compositional variations (16). Low frequency pulsation is also useful in welding thick materials mated by a prepared groove. In these applications the low frequency pulsation is used to obtain proper sidewall fusion as the tungsten electrode is weaved from one side of the groove to the other. In this case the weld current pulsation is synchronized with the cross seam weave pattern, such that the high current pulses occur at each sidewall. This type of low frequency pulsation has proven particularly useful in welding with narrow width groove designs (17-21). Finally, Ecer (22) has shown that the pulsed current arc is more stable against magnetic disturbances than an equivalent constant current arc."

Jan 1, 1986

By Shengli Wu, Mingyin Kou, Laixin Wang, Xinliang Liu, Zhennan Qi, Yujue Wang

Softening and melting experiments were conducted on four kinds of imported lump ores named A-D, under different temperature intervals within the self-developed visualization high temperature furnace. By calculating the reduction and shrinking degree under different intervals, softening and melting indexes were determined. These ores all expanded firstly followed by shrinkage with the temperature increasing. The difference of lump ore’s own characteristic led to different softening and melting behavior. The results showed that the looser the structure was, the better the reducibility will be. The compact structure and good reducibility led to high expansion rate. The beginning softening temperature declined and the ending softening temperature increased because of high porosity, which resulted in wide softening temperature interval. The charging ratio of lump ore A should be improved. Lump ore B should be distributed in the center of the blast furnace. Lump ores C and D should be used less.

Jan 1, 2016

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998