Search Documents

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Johann van Wjk

Mandatory Codes of Practice to Combat Rock Fall Accidents came into force on South African Collieries in 1997. These were drawn up in accordance with guidelines issued by the Chief Inspector of Mines, The Codes of Practice (CoP's) are legal documents in terms of the South African Mine Health and Safety Act 1996. One of the main results Of the introduction of the COP'S from a practitioner's point of view is that they formalized much of what would have constituted a typical visit to an underground section previously. Other important requirements were as Billows: Support rules and Strata Control Standard Procedures were to be drawn tip. Identification of Special Areas (areas requiring a higher level of rock engineering input and with, typically, higher order of support and restrictions on mining geometries), Changing conditions underground to he identified timeously. Implementation of the CoP to he monitored. To comply with these requirements on Ingwe Collieries (a division of BHPO Billiton Energy Coal) it was decided to produce too separate forms to be used in conjunction with each other. The first of these, the "Underground Section Physical Risk Rating" measures the physical conditions in each section whereas the second form, the "Section Perfomance Rating" determines how well the section personnel are Coping with the conditions. This form also pleasures compliance with the Support Rules and Strata Control Standards. Both forms are essentially risk matrices but with various scenarios described, each with a certain weighting. The "Risk and Performance Form" system for bord and pillar operations has by now been used for five years in the Ingwe and Eyesizwe Mining Collieries and has achieved a great deal of acceptance. This system has enabled the quantification of previously subjective observations and has improved the strata control awareness and management of underground mining sections. Amongst other initiatives it has assisted ill reducing the severity and frequency of fall of-ground accidents.

Jan 1, 2002

By G. C. Xiao

A database, incorporating historical data from British mines, to study the factors affecting inflows from proximate aquifers into longwall workings, showed that a main casual factor was the immediate roof strata lithology. When this comprised principally stronger sandstone, there was a tendency for periodic inrushes associated with face weighting. This phenomenon is explained by the collection of water in bed sepa¬ration cavities, where free water connected to a high pressure head aquifer source, may be trapped.

Jan 1, 1990

By Jialin Xu

Bed separations position, size, development characteristics and their influence factors have been analyzed in-depth by experimental and theoretical methods. The results show that the key strata determine the creation, development and space-time distribution of the overburden bed separations and fractures. Based on the dynamic growth principle during the two-stage development of bed separations, the theory of section-grouting for the overburden bed separation space and the O-ring theory for the pressure-relieved methane drainage are proposed. The technique has been applied in some coal mines in China to reduce surface subsidence and for methane drainage. Keywords: rock strata movements; key stratum; bed separation; bed separation grouting; pressure-relieved methane drainage

Jan 1, 2003

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By Yi Luo

Subsurface strata movements and deformations associated with underground mining activities could cause problems to subsurface structures and water bodies. By incorporating the methods for surface subsidence prediction with the subsidence parameters derived from collected subsurface subsidence data, methods have been proposed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining. Two new' types of strata deformations in the field of subsidence research, vertical and total strains that could he useful in assessing subsidence influences to the subsurface structures and water bodies, have peen introduced.

Jan 1, 2000

By George Gardner

The rapid growth of highwall mining in the Appalachian coalfields has resulted in unique safety concerns. Due to the concentration of activity at the base of the highwall and the potentially destabilizing influence of the mining process, proper mine planning and continual monitoring of the ground conditions is essential to ensure a safe and productive operation. This will also help to minimize the need to recover equipment that has become entrapped underground, and the subsequent hazards associated with a recovery operation. Adequate geotechnical site investigation and rational design methods should enable mine planners to properly account for the site-specific conditions that influence web and abutment pillar, roof, floor, and highwall stability. This paper examines the growth of highwall mining, provides a general overview of the various safety concerns, and reviews the modes of highwall failure as they relate to a highwall mining operation. Gcotechnical considerations that should be taken into account before and throughout the mining operation are emphasized. The importance of closely examining and monitoring highwall conditions for subtle signs of highwall instability will be discussed.

Jan 1, 2002

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By K. Haramy

Coal mine bursts or bumps involve the violent, rapid failure of coal and rock in or around a mine excavation. Failure is normally associated with high stress and brittle or brittle-elastic materials; in coal mining, bursting may also be associated with desorbing gas, and this type of failure is termed an outburst. This paper discusses factors affecting coal mine bursts and several methods to predict bursts, including microgravity, microseismic, rheological, rebound, and drilling-yield methods. Methods to avoid burst conditions using volley firing, hydraulic fracturing, and auger drilling are also discussed. A case study is presented in which the redistribution of stresses and displacements was found to be associated with a burst at a deep longwall coal mine. The research showed that stresses are redistributed following the burst.

Jan 1, 1984

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By Megan N. Witkowski

The purpose of this study is to investigate the susceptibility characteristics of domestic and agricultural water supplies that may be vulnerable to diminution or total loss of supply when active longwall mining is in the vicinity of the potable aquifer systems of southwestern Pennsylvania. The study focuses on water supplies in Greene and Washington Counties with reported losses or reductions in supply that were attributed to the seven active longwall mines in operation between 2003 and 2008. The undermined water supplies represent a variety of hydrogeological settings and mining conditions prevalent in the southwestern Pennsylvania longwall coalfield. The susceptibility characteristics investigated include hydrogeological setting, proximal location to mining, and climatic conditions at the time of impact. The investigation considers the relationship between geological and mining characteristics. Geological characteristics include overburden composition and geomorphology of the surface; mining characteristics include mining method, depth, and extraction thickness. It was determined from the study that the average overburden thickness at each mine site is indicative of hydrological changes to potable aquifer systems, with the overall impact frequency at each site decreasing as depth to mining increases. However, depth to mining was not the governing factor when hydrological responses were determined on a case-by-case basis. To fully analyze and hopefully predict potential impacts by longwall mine subsidence, it is necessary to consider additional factors including topography, distance to mining, mining method, and climatic conditions at time of undermining. The investigation serves the purpose of enhancing our understanding of hydrogeological responses to longwall mining and will aid in predicting potential impacts to southwestern Pennsylvania?s wells and springs in proximity to future mining.

Jan 1, 2011

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By S. M. Matthews

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ monitoring of behaviour has been carried out to confirm the mechanisms involved.

Jan 1, 1992

By C. Thomas Blevins

This paper is intended to be a hands on experience account about ground control in a Southern Illinois coal mine. Its aim is to show how a combination of real world mining practices and constraints along with practical engineering theory mesh together to formulate a ground control program in adverse conditions. These conditions - your typical localized slips, splits, rolls, clay intrusions, water, changing types and thicknesses of materials, etc. - being amplified by a very strong horizontal stress field. A review will be made about the formation of the overall ground control plan and to what degree it has been successful. A presentation of the various roof control systems and their component parts, how these systems were developed, and the theory behind them will be made. The pointing out of some of the flaws that we found in the components, installations, and/or theory will be part of this presentation. A brief look at some of the efforts in the following items will be made: quality control of the roof control products; using the computer to help keep track of roof control information and soliciting help from various universities, governmental agencies and consultants to give different perspectives to the problem.

Jan 1, 1984

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997

By Stephen C. Tadolini, Anand Bhagwat

"Intrinsic supports installed in mines with limited seam or mining heights have always proven to be difficult when the required support length is longer. To date, three solutions have been used to ensure that the correct length bolt is installed to achieve the required anchorage or to maintain immediate roof material: combination bolts, milled-notch bolts, and hot-notch bolts. The combination bolts use threaded sections and couples, which can be screwed together to form the required length. The primary bolt of choice, to minimize costs and achieve the desired support, has been milled- or hot-notch rebar bolts. These notches can be placed at strategic (required) locations along the bolt axis, so the bolt can be successfully bent and straightened during the installation process. However, these notches can reduce the strength of the bolting system; special reductions are detailed in ASTM F432-13 (2013). Technical advances in steel rolling and forged heading processes have led to the development of a deformed rebar bolt termed, the BORE bolt, which stands for Bendable Oval REbar. The BORE bolt can be bent at any location and straightened during the bolt installation cycle. This support exceeds the minimum designed capacities described in ASTM F432-13 and meets the yield and tensile strength requirements of a full diameter no. 6 rebar bolt. The profile and shape also reduces the resin annulus during the installation process to enhance mixing and shreds the cartridge film to help eliminate glove fingering.INTRODUCTIONThe height or depth of competent strata material, in the immediate mine roof, can be greater than the developed mine openings heights. This is especially true in coal mine openings where 50% of the minable seams in the US are less than 50 inches (132 cm). When this scenario occurs, it can be difficult to insert steel bolts in a solid single length. Figure 1 illustrates what difficulties can be experienced when a roof bolter operator is working and supporting a thin seam coal mine. There are three viable options currently available. Lengths of the bolt can be threaded and a steel coupler can be used between the sections to reach the required depth of anchorage. These systems, called “coupled bolts,” usually require a larger diameter hole to facilitate the larger coupler diameter and can be anchored with an expansion shell, resin, or a combination of both. To ensure that the coupler will develop the tensile capacity of the bolting system, required by ASTM 432-13 Standard Specifications for Roof and Rock Bolts and Accessories (2013), the threaded bars should be completely rotated and engaged into the coupler. Premature failures can occur when the threads “strip out” if not inserted completely."

Jan 1, 2018

By Nicole E. Evanek, Anthony T. Iannacchione

"Over the past 36 years, a great deal of information has been presented and discussed at the International Conference on Ground Control in Mining (ICGCM). The topic of surface subsidence engineering has resonated throughout each of the 36 conferences, producing 155 related papers. These papers have come from many countries. The major focus has been underground coal, especially longwall mining, but hard rock mining has also received attention. This impressive collection of reports presents a unique opportunity to reflect on the progress made towards understanding subsidence basin characteristics and developing methods to predict and mitigate its impact.In the initial meetings, the focus was on measuring subsidence and developing prediction methods. As understanding increased, predictive methods were developed and tested, especially in North America, China, Australia, Europe, and India. Efforts were made to understand how structures, aquifers, and surface waters were impacted by the formation of subsidence basins. As time progressed, the number of papers dropped slightly and became more focused on site-specific conditions. Most recently, advanced monitoring techniques have revealed new information, spurring a resurgence in research activity. Another recent focus has been on anomalous horizontal deformations occurring in sites with significant relief. Several reports from Australia and one from the US have brought this issue to light. In closing, all of these surface subsidence engineering papers have chronicled the maturing of this most important topic and, in the process, highlighted the importance of the ICGCM in the evolution of our current state of practice.INTRODUCTIONThe aim of this paper is to examine the role of ICGCM in 1) shaping our understanding of the mining induced subsidence phenomena, 2) developing tools to help predict its impact on the surface, and 3) evaluating controls to mitigate these impacts.This analysis involved the consideration of 155 papers available within the ICGCM conference proceedings and listed under the subsidence topic. Three of the papers where only available as abstracts and were not included in this analysis. Four other reports were focused on topics other than underground coal mining-induced subsidence issues and were also not included. It should also be noted that papers dealing with overburden behavior were not included in this analysis. As a result, 148 papers were reviewed and analyzed (Figure 1)."

Jan 1, 2018

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors' underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By Yongping Wu

Taking the longwall mining face area in a steeply dipping seam as the research object, the stability of an asymmetrical rock mass structure is analyzed using shell theory and masonry beam theory. The results show that an asymmetrical shell structure is formed at the top strata of the mining stope and its magnitude is mainly determined by the mechanical characteristic of the overburden strata of working face, mining space size and so on. Localized instability of the shell structure is the main factor that leads to the overall structural instability in the stope. The instability modes includes: the shell roof instability dominated by tensile failure, the shell shoulder instability initialized by compression-shear failure, and shell bases composite instability occurs in tensile and compression-shear modes. The shell structure stability dedicates rational strata control measures to choose, and the caving height of overburden strata is the key for shell structure instability.

Jan 1, 2013