Search Documents

By Peter Zhang, Daniel Su, Mark Alexander Van Dyke, Heather Dougherty, Bo Hyun Kim

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a post-mining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64°, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457-m wide and 3657-m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones in longwall gobs.

Jun 9, 2022

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By Yun Bai, Sarah Wilson, Michael Salcher, Mark Trim

Over the last decade more than 62 miles (100 km) of civil transport tunnels were constructed in Sydney, Australia, using the sequential excavation method (SEM). The WestConnex motorway tunnels, each stage of which used over 20 roadheaders to excavate up to 40 tunnel headings, had numerous caverns up to 100 feet (30 m) wide and 82 feet (25 m) high. SEM tunnels in North America typically have far fewer active headings. This paper examines the differences in scope and risk allocation for construction phase services, including comparison of the Permit to Tunnel (PTT) process in Australia and the Required Excavation and Support process in North America.

Jun 23, 2024

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By Michael Murphy, Gamal Rashed, Brent Slaker

Pillar stability continues to be a significant concern in multiple-level mining conditions, particularly for deep mines when pillars are not stacked or the thickness of interburden between mining levels is thin. The National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to investigate the stability of pillars in multiple-level limestone mines. In this study, FLAC3D models were created to investigate the effect of interburden thickness, the degree of pillar offset between mining levels, and in situ stress conditions on pillar stability at various depths of cover. The FLAC3D models were validated through in situ monitoring that was conducted at a multiple-level stone mine. The critical interburden thickness required to minimize the interaction between the mining levels on top-level pillar stability was explored, where the top level mine was developed first followed by the bottom level mine. The model results showed that there is an interaction between numerous factors that control the stability of pillars in multiple- level conditions. A combination of these factors may lead to various degrees of pillar instabilities. The highest degree of local pillar instability occurred when pillar overlap ranges between 10 and 70%. On the contrary, the highest degree of stability occurs when the pillars are stacked, the underlying assumption is that the interburden between mining levels is elastic (never fails). Generally, for depths of cover investigated in this study, the stability of top-level pillars shallower than 100 m (328 ft) or with interburden thicknesses greater than 1.33 times the roof span—16 m (52.4 ft) in this study—does not appear significantly impacted by pillar offset. The results of this study improve understanding of multiple-level interactions and advances the ultimate goal of reducing the risk of pillar instability in underground stone mines.

Jul 27, 2022

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By James E. Lawver

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent or at least delay mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the forms of calcined bones at least 2 000 years ago, (1) and man has used phosphate minerals as a source of fertilizers in one form or another for at least 100 years. During 1977 the world produced about 116 million metric tons of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows. Marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits, requiring an apatite carbonate mineral separation.

Jan 1, 1978

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, M. RAJU, GANESH SHETTY

With the depletion of high-grade iron ore resources, the utilization of existing low-grade iron ores, fines and tailings with effective beneficiation is inevitable to meet the iron and steel industry’s required specifications and demand. JSW Steel Limited is operating a 17-mtpa beneficiation plant at its Vijayanagar site in Bellary in Karnataka, which produces nearly 50 to 54 percent concentrate as sinter-grade fines. The sinter base mix consists of iron ore fines that are smaller than 10 mm, with 41 percent smaller than 0.150 mm; washed ore that is generally smaller than 3 mm and bigger than 0.150 mm, with 3 to 9 percent smaller than 0.150 mm; beneficiation plant concentrate, with 97 percent smaller than 0.150 mm; limestone; dolomite; coke breeze; lime; sinter return fines; direct reduced iron (DRI) fines; and micropellets produced from steel plant waste. Using more washed ore in the sinter base mix affects the sinter quality. Ball formation in the mixing and nodulizing drum is an important step in sinter making and requires sufficient quantity of smaller than 0.150 mm fines. Optimization of fines in the sinter base was carried out by replacing the smaller than 10 mm iron ore fines with washed ore. Size analysis, study of the granulation index (G index) and optimization of moisture with respect to sinter bed permeability were carried out to optimize the proportion of smaller than 0.150 mm fines in the sinter base mix as adhering material. This study explores the optimization of fines in the sinter base mix for ball formation to achieve higher sinter quality and productivity with higher sinter bed permeability.

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 7, 2017

By G. Bonifazi

The study of minero-petrographical characteristics and the subsequent textural and structural characterization of an ore mineral represents the first step of each industrial processing whose aim is the beneficiation of each valuable mineral phase present inside the ore. Analytical, mineralogical and petrographical, chemical and multispectral image analyses based investigations, applied to eclogitic ore samples deriving form "in situ" sampling campaigns, were applied. These procedures enabled to point out some textural and structural aspects characteristics of ore litotypes belonging to eclogitic-amphibolitic dikes. Such dikes are characterized by a paragenesis constituted mainly by siliceous gangue and accessory "useful titanium minerals" as rutile [TiO2], "pseudolilmenite", ilmenite [FeTiO3] and sphene [CaTiSiO5]. In the beneficiation process applied to ore s is of preliminary importance to establish a strategy in order to obtain a recovery of high quality "mono-minerals concentrates" as rutile, "pseudolimenite", ilmenite and phene. To reach this goal is thus necessary to develop a preliminary study of the textural, structural, petrochemical and minerochemical characteristics of the samples. Different ore samples (eclogitic rocks), resulting from sampling campaigns carried out in the Piampaludo area (Sassello district: Savona, Northern Italy), are examined.

Jan 1, 1994

By W. Perkins

The Smoky Canyon Mine has recently installed a PROMPTED GAMMA NEUTRON ACTIVATION ANALYSIS (PGNAA) on-line analyzer as part of a long-term advanced process control program. The on-line analyzer was adapted from a continuous dry analyzer and a large on-stream wet analyzer to a compact, multiplexed 3" slurry analyzer. The analyzation feed system utilizes a multiplexer system to accommodate up to fourteen (14) different plant process streams. The corresponding sampling system also provides for dewatering of sample streams too dilute for timely analysis. Key analysis includes, but is not limited to, phosphorus, aluminum, magnesium, calcium, and potassium. This data currently allows plant operations to be manually evaluated and controlled. Future development of a plant-wide supervisory control system will utilize the data for plant operations. This paper discusses the design, installation, and operation of the PGNAA on-line analyzer at the Smoky Canyon Mine.

Jan 1, 1996

By Omid Asghari, Seyed Reza Ghavami-Riabi, Sajjad Talesh Hosseini

Separation of geochemical anomalies from the background using various methods for identifying areas of higher mineral potential is a critical first step in Greenfield and Brownfield programs. There are several methods for differentiating anomalous regions from the background. The U-spatial statistics is an effective technique that provides the opportunity of reaching this goal by considering the geochemical sample locations in the separation of geochemical anomalies. In this study, a developed form of the U-spatial statistics method is introduced, which not only considers the existence of anisotropic spatial variations in input data but also reduces the computational (CPU) time. While the previous method is based on the isotropic assumption in the study area and a set of search windows at different times, here, the geochemical anomaly is determined by pasting only one ellipsoid window, effectively combining the flexibility of the U-spatial statistics method with the advantages of geostatistical approaches. This paper compares various approaches (the previous and developed version of the U-spatial statistics method, concentrationarea (C–A) fractal model, and probability diagram modeling) for the separation of anomalous areas in the presence of heterogeneous spatial variations. This is done with an application to a Baghqloom porphyry copper deposit located in southeastern Iran. The high potential areas identified via different approaches show an anomalous region in central parts of the Baghqloom area, which partially coincides with an intense potassic alteration area. Compared to other methods, our algorithm separated the high potential areas at a greater spatial resolution.

May 3, 2021

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984