Search Documents

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

By R. H. Thorpe

In the earliest days of mining coal the obvious method was by bord and pillar working. Longwall in Britain developed from this as an expedient to overcome bottlenecks arising from ? 1) increasing depth of seams causing roof control difficulties; and 2) ventilation problems. This system became almost universal particularly in the thicker seams, where faces of up to one mile in length were not uncommon. Coal getting in these faces was usually by pick and shovel, filled into small waggons of up to 15 cwts capacity. These waggons ran on rails laid alongside the coal face and were often taken away from the face to the main haulage roads by horses. The roof was supported by rigid props and the wastes were normally controlled by strip packing. This system of mining was very flexible and worked well down to sections of about 3'6"

Jan 1, 1976

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By Ernest N. Wolff

You here are all familar with the myriad of new laws, some enacted and some pending, that affect the mining industry. These laws, for example those dealing with suspended matter, affect us in Alaska as they do you. Likewise, our friends in government, the Geological Survey and the Bureau of Mines, provide us with the same fine services that they do elsewhere. I am not going to speak today about these, but concentrate on one act of Washington, D.C. the impact of which is felt, for now at least, principally in Alaska. A little more than a year ago, I spoke in Spokane on the subject, "Governmental Challenge to Mineral Development in Alaska." I outlined some of the policies of Government which were operating to change the rules under which the industry operates and to alter the relation- ship between government, industry, and the individual. At that time the Native Claims Settlement Act had not been passed, but was on the verge of being so. In reading over what I said in Spokane, I note that I touched on many points where Government was actually challenging mineral development in Alaska. With the passage of the Alaska Native Claims Settlement Act, many of these actions were given a cloak of legality, and machinery was set up to concentrate the drive to tie up the public domain, machinery which will allow govern- mental control and interference with the actions of individuals on something like 90% of Alaska's land surface. This remarkable law is going to affect each and every one of you. Now, a year after its passage, we are only just beginning to see its lesson for the future. It was created by a coalition of powerful groups, who got other groups to support them by promising to deliver something they had no intention of delivering. Alaskan issues are again being used to get various groups not to oppose legislation which will severely harm them. It will help to understand the nature of this new drive if we understand the Native Claims Act and how it came into being.

Jan 1, 1973

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By R. M. Schuster, F. M. Benavides

Samuel G. Bonasso The article by Benavides and Schuster provides an in-depth study of three transportation alternatives for a four-mine complex in western Kentucky. The examination of aerial tramways was not undertaken as an alternative solution. We feel this is an oversight since industrial ropeways are competitive with both belt conveyance and overland truck hauling. In fact, there are aerial tramway systems, operational today, which are 100 years old and operating with some original components. Maybe unfortunately, there are no fixed rules or guidelines whereby the most cost-effective means of transporting and handling material for a given situation may be selected. Each situation must be evaluated so the variables that influence the selection of the desired alternative can be clearly defined. However, there are in-place industrial ropeway systems that have proven economically feasible over a range of 1.6-50 km (1-31 miles). The more difficult the terrain, the greater the cost efficiency.

Jan 1, 1983

By N. S. Tanious

This work was completed prior to the author's appointment with the Nuclear Regulatory Commission (NRC). Therefore the views and conclusions contained in this paper are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the NRC. Reference to specific brands, instruments, or trade names is made to facilitate understanding and does not imply endorsement by the author or the NRC.

Jan 1, 1987

By George W. Leney

The iron ore industry might justifiably claim to have originated the science of geophysical prospecting. Their use of geophysical methods was probably the first application of these scientific techniques to the search for economic materials although the exact origin is undoubtedly lost in the unrecorded observations of. some prospector experimenting with compasses or bits of lodestone. Since 1879 when Thalen published "On the Examination of Iron Ore Deposits by Magnetic Measurements" these methods have been a standard supplement to other prospecting techniques. However, many of the great ore bodies of the Precambrian iron ranges were not particularly suitable for geophysical work. The ores were oxidized and enriched through leaching of silica so that they were nearly non-magnetic and other physical properties which distinguished them from the wall rocks were largely destroyed. With the gradual exhaustion of these high grade direct shipping ores, and ores that could be beneficiated by simple means, the iron ore industry turned initially toward the importation of similar high grade foreign ores. At the same time, new processes for concentrating lower grade materials were being developed and older ones improved upon. These concentrates' when pelletized produced such important savings in blast furnace hot metal costs that they now command a premium in the iron ore market and have weakened the competitive position of the remaining high grade ores. The ore bodies now being sought are usually unoxidized and frequently they are also metamorphosed.

Jan 1, 1965

By R. D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of general accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2000

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By C. E. Capes

The continuous balling? operation whereby a moist particulate mass is tumbled in a horizontal revolving drum with recirculation of the undersize product can be extremely unstable. Product and recycle rates are subject to wide fluctuations. Although the problem seems to be well-recognized, there is little published information or quantitative data readily available, especially in relation to industrial-scale circuits. Probably the best available published results are in the Russian literature, an illustration of which is given in Figure 1. These data, taken from a study') of some of the factors which influence the stabilization of the pelletizing process, illustrate the wide variations in circulating load and circuit productivity which may be encountered over a period of operation. The problems of balling circuit stability may be traced to random seed or nuclei generation and uncontrolled agglomerate growth. The situation is analogous to that in crystallization processes where (4 considerable attention is given to nucleation control. Traditionally attempts have been made to optimize system and operating variables to stabilize the balling process. A supplemental approach which is taken here is to build on the considerable

Jan 1, 1975

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

Those involved in the mining and minerals industry really are an optimistic bunch. Faced with an economic downturn that has spread across the globe ? one, some say, that crept up on everyone ? mining professionals remain hopeful that the industry will return. An example of that optimism is the attendance at two of the industry?s key conferences and exhibitions. In February, more than 4,200 people attended the SME Annual Meeting and Exhibit in Denver, CO. And a week later, in Toronto, Ontario, more than 18,000 were on hand for the Prospectors and Developers Association of Canada?s (PDAC) meeting. Both are respectable numbers and run contrary to meeting attendance figures during previous downturns when attendance and the numbers of exhibitors fell off significantly. Like other downturns, this most recent one has resulted in massive layoffs, curtailments of production and outright closures. Exploration has been hard hit and many junior mining and exploration companies will either disappear or be swallowed up by others. Gold is its usual self The PDAC generally attracts the gold mining and exploration sectors. So that might explain some of the optimism at the meeting. Unlike base metals and construction materials, gold, not surprisingly, is doing well. And most of the companies in the Investors Exchange at PDAC were involved with gold. While the balance sheets for most base metals companies look bad, gold companies appear to be not as hard hit. Gold is doing what it usually does during a downturn ? act as a safe haven while the value of other assets collapse worldwide. Governments around the world are preparing to pour trillions of dollars in an attempt to resuscitate their economies. This will likely lead to inflation, some experts at the PDAC convention said, which will be good for gold. And gold mining companies are also benefiting from lower production costs. The result is that some gold watchers believe gold could reach $64/g ($2,000/oz) at some point.

Jan 1, 2009

By Ehsan Moosavi, Kamyar Tolouei, Mehran Gholinejad

The literature defines rockbursts in slightly different ways based on their generation mechanisms, field phenomena, and degree of damage, but in a way that is almost consistent. Generally, a rockburst refers to seismic events that mainly happen in underground excavations, for purposes such as underground mining, road and railway tunnels, nuclear power, etc., and that are followed by the collapse and outburst of rocks. Long-term rockburst prediction can be abstracted as a classification problem mathematically, in which we can introduce deep learning to solve it. Further, using deep learning in rockburst prediction can overcome drawbacks such as subjectivity and inconsistency brought from previous traditional approaches. A rockburst data-set, was employed to evaluate the current method for predicting rockburst grade, and the good results of overall success rate were obtained. The results indicated that the proposed algorithms can speed up parameter optimization search, the proposed method is robust model and might hold a high potential to become a useful tool in rockburst prediction research.

Apr 26, 2022

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometry of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers, and management and will help mine operators plan the optimum mining sequence for different mine geometries and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2001

By Robert N. Morris

Ladies and Gentlemen: It is a distinct pleasure and honor to appear before you representing the railway industry as I do, but there is a much closer personal relationship. I am a graduate Mining Engineer and worked in the coal industry for 15 years prior to becoming a railroader only 4 ½ years ago. I have been a member of AIME most of my adult working life and am currently active in the Washington, D. C. Section. While having been in the railway industry only a short time, I have become involved during the recent period of innovation and development of the new railroad technique known as unit train service. I have had the privilege of helping to work out a number of unit train movements to both electric utility companies and to a major steel concern, handling coal from mines on the Southern Railway to the consuming plants. On Southern, our unit trains are all of what I shall describe as shuttle train operations whereas within the railroad industry today several types of service are characterized as unit train service and many don't offer comparable efficiencies.

Jan 1, 1968