Search Documents

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By F. Freme

Coal production in the United States reached a record level in 2005, ending the year at 1.03 Gt (1,133.3 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2005 was 19.2 Mt (21.2 million st) higher than the 2004 level of 1 Gt (1,112.1 million st) and surpassed the prior record set in 2001 by 5.1 Mt (5.6 million st). Although total U.S. coal consumption rose in 2005, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sector by 2.2 percent and declined in the other industrial sector, while coking coal consumption decreased slightly.

Jan 1, 2006

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

By James W. Clark

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1984

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By K. R. Long

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to re-estimate ?Taylor?s Rule? which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

Jan 1, 2011

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005

By T. P. Dolley

Domestic production of industrial sand and gravel in 2004 was about 29 Mt (32 million st), a 6-percent increase from 2003. This increase was buoyed by a robust construction sector of the U.S. economy. U.S. apparent consumption was 30.3 Mt (33.3 million st) in 2004, an in-crease from 2003. Imports were about 490 kt (540,000 st) in 2004, an 11-percent increase from 2003. Imports of silica are generally of two types. They include small-quantity shipments of very-high-purity silica or a few large shipments of lower grade silica that were shipped only under special circumstances (such as very low freight rates).

Jan 1, 2005

By Diler Katircioglu-Bayel

This manuscript aimed to examine the impact of operating parameters on the wet grinding of talc in a vertical-type stirred media mill. Within the scope of the research, the effects of operating parameters including media filling ratio, solid mass fraction, grinding media size, and grinding time were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw), and energy consumption (Em). As a result of the present research, the following optimum grinding test conditions were determined: 65% media filling ratio, 40% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. After determining the optimum grinding conditions, the Box–Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio was found to significantly affect the decrease in d50 compared to the other two parameters. Furthermore, the minimum d50 size was also achieved under optimum grinding conditions.

Aug 12, 2020

By R. Kaushik

According to the U.S Department of Energy (DOE), mineral processing activities including comminution (size reduction) uses 4% of the world electrical energy consumption. Such numbers reinforce the need to invest in energy savings initiatives in order to produce more using less. ENERGY EFFICIENCY OPPORTUNITIES AND CHALLENGES IN MINING OPERATIONS In addition, DOE, in its Mining Industry Energy Bandwidth Study, has identified huge potential for energy savings for the coal, metals and mineral industries. Even knowing the overall causes of energy waste and some potential tools for remediation, mining companies may struggle to apply such tools and get the desired results due to the following reasons: ? Limited staff ? Lack of accurate economic and investment analysis to justify energy savings projects ? Lack of knowledge to identify low or no-cost savings opportunities ? Internal competition for resources According to the workforce and talent management experts, the Talent Strategy Advisors, the demand for mining engineers is expected to exceed supply by 30% by 2013. Mining personnel are likely to be burdened with increasing and varied workloads with limited training. This will result in the need for automated and simple tools to support energy efficiency activities. Mining engineers will simply not have the time and resources to create such tools, collect and analyze the data to make decisions, and track results.

Feb 27, 2013

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By X. Zhou

In this study, the cyclonic static microbubble flotation column (FCSMC) was investigated for fluorite beneficiation. The structure and principle of the specially designed column are described. Fluorite samples from the tungsten separation tailings of the Shizhuyuan Mine, Chenzhou, Hunan Province, P.R. China, were tested using a small-scale continuous flotation test unit, and concentrates with a fluorite grade higher than 98% were obtained. One rougher and three cleaner stages in the FCSMC achieved the same separation performance as one rougher and eight cleaners in conventional flotation cells. This greatly simplified the flotation circuit and reduced operating costs.

Jan 1, 2007

By J. C. Yingling

[New stochastic process models are developed to calculate the probability of various fill levels in section feeders as a function of vehicle interarrival times, payloads and feeder-discharge rates. These models may be utilized to establish the minimum feeder-discharge rate necessary to prevent a feeder, with a particular surge storage capacity, from constraining the section's production rate. In addition, it is shown how the output from these models may also be utilized to calculate the probability of various flow rates at junctions in the conveyor haulage network, enabling one to size gathering belts. The model provides a basis for optimizing, (in economic terms) capacity specifications for feeders and conveyor belts in the materials-handling system by considering tradeoffs in the size of the two types of units.]

Jan 1, 1997

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992