Search Documents

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By A. W. Cramb

A three-day symposium on the production of clean steel organized by The South African Institute of Mining and Metallurgy, was held in September 1995 at Vanderbijlpark. It was attended by 151 delegates, who represented the whole of the steel industry in South Africa: Iscor Works, Saldanha Steel, Columbus Stainless, Highveld Steel & Vanadium, Iscor Research & Development, University of Pretoria, and Technikon Witwatersrand, as well as the users of steel products were represented. Professor Allan Cramb held the delegates attention with well-presented research and practical information. He obtained excellent interaction with the delegates by responding in depth to the questions put to him during the Symposium. In summary, he emphasized the following aspects of the elimination of defects during the processing of steel in continuously cast materials.

Jan 1, 1996

By F. T. Cawood

The distinction between real estate ownership and that of interests in the property is fundamental to the appraisal of mineral properties. This distinction affects the nature and understanding of security of tenure and, consequently, the perception of what constitutes fair value. Legal matters are a particular concern because of their influence on security of tenure, ownership definition and use restrictions. The dynamics of the market and the complex interrelationships between the factors of production define value at a specific point in time for the bundle of rights, interests and assets that constitute a mineral property. Because each mineral property is unique, physically immobile and of a wasting nature, its usefulness to its owner and society must be optimized. The US Appraisal Institute (2001) classified the forces that affect land use as the cultural, political and economic attitudes of society. These forces culminate in laws that often dictate the purposes for doing appraisals. Once the legal definition of the asset is understood, valuers can decide on the valuation process that will support the final valuation approach.

Jan 1, 2004

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By A. Basçetin

Equipment selection in mining engineering is one of the most important decisions that affects the mine design, production planning and economic parameters in open pit and underground mining. Mine planning engineers generally use their intuition and experiences in decision making. Mostly, linguistic variables (the weather is raining, soil is wet, etc.) come into question and decision-makers may not know how these variables are computed. Since the advent of the fuzzy set theory, these uncertainties are easily interpreted in the decision-making process. The development of computer technology and programming of colloquial language with expert systems have considerably reduced decision-makers? burden. This paper reviews the development of a computer programme software called EQS (EQuipment Selection) that automates equipment selection in mining engineering using fuzzy set theory. The EQS with an introduction of the concepts and theories of multiple attribute decision-making, the fuzzy set theory, and EQS applications to mining industry problems with case studies are presented

Jan 1, 2006

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By S. Montes

Mineral floatability is strongly connected with mineral structure and composition. The complexity of mineral surfaces has meant that few attempts have been made to understand the effect of impurities (trace elements) on the flotation process. Zeta potential technique has been extensively used to evaluate the surface charge of mineral particles. Nevertheless, those measurements consider only an average of mineral particles surface charge. The presence of fine particles and inclusions covering a mineral may influence the local reagent adsorption process, which will ultimately be reflected in the subsequent global response of the mineral froth flotation efficiency. The current work assesses the iron oxide mineral, haematite (Fe2O3). Zeta potential and streaming potential techniques were used to determine the surface charge of fine and coarser particles of haematite. Further analysis was performed to determine the point of zero charge (PZC) of the mineral. In addition, adsorption isotherms of alkyl ammonium chloride reagents with different lengths of carbon chains were carried out. It was found haematite floatability depends strongly on the isoelectric point (IEP) value, which is affected by other mineral species present at the mineral surface. Haematite floatability became significant only at relatively high tetradecyl ammonium chloride collector concentrations (concentration greater than 4 10-4M), which does not happen with other oxides such as quartz. Unlike quartz, haematite develops a low surface charge over a wide range of pH, disabling all long-range attractive interactions between the mineral and the collector. Therefore, hydrophobic chain interaction is probably the most likely mechanism acting to promote collector adsorption and enhance further floatability. Diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) was used to suggest a possible mechanism to understand the sequence of collector adsorption and the effect of trace species on it. Keywords: floatability, haematite, adsorption, electrochemistry, zeta potential.

Jan 1, 2007

By H. E. Bartlett

In the operation of some flotation plants treating platinum ores it was found that there were imbalances between the inputs and outputs. The inputs and outputs were sampled as slurries and it was determined that the imbalances arose from biases in the sampling, despite the samplers having been designed according to well-established rules. The launders feeding the sample cutters, and the sample cutters themselves were redesigned using finite element analysis to model the flows. A new set of design rules were formulated. The application of a Components of Variance Analysis, to determine the variance of primary and secondary sampling and of analysis in the lab for a concentrate is presented to illustrate the need for frequent sampling of process streams.

Jan 1, 2002

By E. Matinde

Poor phase separation and fine dissemination of the desired components within congruous slag phases are key challenges limiting the recoverability of values from slags by conventional beneficiation methods. Slag microstructure conditioning is a pragmatic approach to increasing themvalue-in-use of discard slags, especially when integrated with the broader smelter infrastructure. Although not yet tested on oxide slag systems, this paper explores the potential application of magnetohydrodynamic principles to the crystallization behaviour of bulk slags. Integrating the slag microstructure conditioning infrastructure to the existing smelter infrastructure is key to unlocking the economic value of slags because it is most economic to condition the properties of molten slag directly after tapping. A new business model that integrates smelting units to transversalmeconomic activities, such as cement production and suppliers of construction aggregates, canmsignificantly increase the circularity of metallurgical slags.

Oct 9, 2024

By W. P. Roux

Owing to decreasing high-grade ore reserves, there is a need for better understanding of the jigging process to improve the recovery efficiency of finer, lower grade material. The use of positron emission particle tracking (PEPT) was examined as a technique to study the motion of iron ore particles inside a laboratory batch jig. PEPT is a non-invasive method that can provide three-dimensional kinetic data on a particle in laboratory-scale processing units and has been successfully used to study mills, hydrocyclones, and flotation. Experiments were conducted to determine whether PEPT would be a viable technique to study iron ore jigging and what valuable information could be obtained. The results indicated that detailed information on the stratification rate of a particle could be obtained, with adequate resolution to track the particle?s movement through an individual jig pulse.

Jan 1, 2014

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate, while increasing it decreased the corrosion rate. Keywords: austenitic stainless steel, % ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentio-dynamic scans, microstructure, chemical analysis.

Jan 1, 2007

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By I. A. Mutemererwa

This paper investigates the role of vertical integration between chrome ore mines and ferrochromium smelters in the location of ferrochromium production capacity in South Africa and Zimbabwe. Vertical integration is important in understanding the increasing competitive position of these two countries as observations show that an increasingly larger share of the global market has been coming from integrated producers. The paper argues that the increased vertical integration between mines and smelters in South Africa and Zimbabwe has led to a lower cost of chrome ore as an input compared with other producers. Underlying this hypothesis is the basic tenet that, more likely than not, production will take place where the costs are lowest. The paper concentrates on high carbon ferrochromium (HCFC) production in market economy countries (MEC). Using an ordinary least squares model, the study tests the relationship between low chrome ore costs and vertical integration shows a statistically significant relationship. These findings partially support the view that the control of sources of chrome ore is a major source of competitiveness. Keywords: competitiveness, ferrochromium (ferrochrome), ordinary least squares, dummy variables, vertical integration, southern Africa.

Jan 1, 2000

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By A. J. Geldenhuys

This paper will focus on two topics, namely (1) an innovative process for the neutralization and partial sulphate removal of acid streams produced during coal mining and processing and (2)optimization of this integrated neutralization process by adding small amounts of synthetic organic polymers. The integrated lime and limestone process has been developed to neutralize acid mine water and to remove sulphate (to less than1 200 mg/l), magnesium and metals. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1 500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. The process consists of the following stages: 1. Limestone (CaCO3) neutralization to raise the pH to 7 and CO2-production. 2. Lime (Ca(OH)2) treatment to pH 12 for Mg(OH)2precipi-tation and gypsum (CaSO4.2H2O) crystallization. 3. pH adjustment with CO2recovered from stage 1 and CaCO3 precipitation. Retention times of 1 hour, 4 hours and 1/2an hour were required by stages 1, 2, and 3 respectively. The sulphate level was reduced to 1 094 mg/l, which is less than the original aim of 1 200mg/l. Chemical costs associated with neutralization, using limestone instead of lime, are reduced by 69% in the integrated limestone/lime process. The overflow water from the clarifier of each of the above stages generally contains a wide variety of colloidal impurities that may cause the water to appear turbid or may impart colour. This results in very slow sludge settling rates that cause overflow water with a high degree of turbidity and colour. There are a number of successive or simultaneous stages involved in the agglomeration of particles. To get optimum neutralisation of the acid water and partial sulphate removal to below the saturation level of gypsum (i.e. 1 500mg/l), maximum sludge recovery is needed. The higher the concentration of seed crystals, the larger the surface area. Therefore, effective removal of suspended and colloidal matter from the overflow of each stage is required and can be achieved by coagulation and flocculation. The polymers PAC6 and 3095 were effectively used as coagulant and flocculant respectively. The addition of these polymers resulted in a clear overflow in each of the above stages with a very low turbidity.

Jan 1, 2003

By J. A. Bakken, T. Magnusson, G. Sævarsdottir

This paper describes measurements of current and voltage done on submerged arc furnaces. The aim is to focus on and attempt to separate from one another the electric arc current and the current bypassing the arc through the charge. Toward this goal two measurement campaigns on AC-arcs burning on coke beds are ac-counted for. The first was done on a 150 kVA pilot furnace at SINTEF in Trondheim Norway, and the second one was done on a 48 MVA industrial furnace run by Icelandic Alloys in Iceland. The measurements were compared to simulations employing an advanced MFD arc model. The main results are that a coke bed does not necessarily behave as a linear conductor. However the warmer chemically transformed part of an operating Si-metal or FeSi furnace probably exhibits linear behaviour and passes a considerable fraction of the phase current, perhaps on some operating conditions, as much as 50%.

Jan 1, 2007

By K. Schwerdtfeger

Data are presented on the effect of iron oxide on the electrical conductivity of CaO-SiO2-FeO-Fe2O3melts, and on limiting current and impedance in direct current or alternating current charge transfer at iron electrodes. The strong influence of iron oxide content can be utilized for in situ determination of total iron oxide content and Fe3+/Fe2+ratio. The possible probe designs are presented and the principles and procedures of the measurements are explained. Keywords: in situ probe for iron oxide determination in steelmaking slags, electrical conductivity of CaO-SiO2-FeO-Fe2O3slags, direct current over voltage and alternating current impedance at iron/slag electrodes.

Jan 1, 2004

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely: codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage like nuclear power generation where international cooperation is eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit their mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2003