Search Documents

By P. Henning

Rock fall accidents continue to be the main cause of fatal and serious injuries in the mining industry. Although there has been an improvement in the FOG (falls of ground) related fatal and serious injuries over the past few years, the rate is still too high. New technology has made it possible to reduce this rate significantly. FOG accidents imply failure of the support system or the design of the support system in use. In this paper we deal with the latest technology available to assist the mines to reduce the rates of FOG related injuries and fatalities.

Jan 1, 2010

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

Minutes of meeting held at the Moth Hall, Witbank on 13th November, 1969. There were present eleven members: Mr J. Meintjes (in the chair); Messrs I. E. van Aswegen, O. T. Wright, A. W. L. Brereton, A. Bain, J. Brook, P. J. Beukes, C. H. Coxon, B. F. v.d. Merwe, A. C. Hofmeyer, G. E. Carlyon. Six Associate Members: Messrs E. J. Jackson, J. N. H. Pritchard, R. E. Powell, W. Weber, R. Smith, B. T. Hosking. One Student Member Mr M. J. de Beer. Seven visitors. The Chairman reminded members of the intended visit to Barberton. Dr Stander, Director of the National Institute for Water Research, gave an interesting talk, illustrated with slides and a short film, on the conservation and reclamation of water in South Africa. After question time, Mr Hector, Witbank Town Engineer (visitor) thanked Dr Stander. The meeting closed at 7.10 p.m.

The first annual student prizegiving function of the South African Institute of Mining and Metallurgy was held in the Dorothy Susskind Auditorium, University of the Witwatersrand, on Thursday, 26th May, 1977. The address (see opposite page) was given by Dr M. G. Atmore, a director of Anglo American Corporation and Vice-President of the Institute.

Jan 1, 1977

By Paul B. Crawford, Gerald N. Pitts

"A new method is introduced for the simulation by computer of the flow of liquid underground. The method has application in simulating, for example, liquid withdrawal systems, injection systems or injection-well systems. The computer simulation of liquid flow permits the utilization of the known properties of the rock in developing a model of the permeable rock mass.The flow properties of the rock at a specific site arc generated statistically using a random number generator. After defining in this manner the rock properties of each element in the computer grid, the streamlines or flow paths of the liquid are traced using the new method. The simulation is designed especially for computers. The meandering character of the liquids paths is displayed clearly as the fluid moves underground, thus providing the technical information required for the control of the movement of liquid."

Jan 1, 2014

By M. Grave

Rock Engineers are required to design safe cost effective support systems and stoping layouts for their respective mines. As each stope has its own unique environment, continual re evaluation is required in all stopes to maximize extraction and achieve value from the support standard. This paper presents numerical modelling used to plan early mining within the shaft pillar and a reevaluation of an existing stope support standard.

Jan 1, 2009

The September General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th September, 1970, at 3.00 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present one hundred and eighteen Fellows, including Dr J. M. Bereza, H. P. Carlisle, R. J. C. Goode, Dr J. P. Hugo, P. Lambooy, Prof R. P. Plewman, W. W. Malan, Dr J. T. McIntyre, Dr M. D. G. Salamon, L. W. P. Van den Bosch, P. A. von Wielligh (Council Members), A. Bain, G. P. Bennet, D. L. Carson, G. L. H. Diering, M. E. E. Douglas, F. A. B. Fouche, R. Fourie, A. R. C. Fowler, E. B. Gordon, J. S. Hay, G. H. Henderson, S. D. Hill, A. C. Hofmeyr, J. M. Jacobs, A. F. Lee, D. G. Malan, L. J. Prince, W. G. Pyne-Mercier, A. H. Mokken, Dr W. S. Rapson, R. R. Richardson, H. V. Solomon, C. G. Sowry, G. G. Stanley, G. R. Still, D. L. Starkey, D. L. Taylor, E. W. Thiel, I. E. Van Aswegan, M. van Ryneve1d Steyn, N. B. Vinson, H. Wheeler, Dr A. Whillier, R. A .Wilson, C. F. Ziervogel. Forty-two Members including R. C. Bertram, F. Collier, G. C. Currie, O. Davel, J. M. Gosnell, A. Hazell, Dr N. C. Joughin, F. Kleinschmidt, D. Love, R. B. Macgillivray, D. Mather, R. D. R. Munro, R. S. Pearson, J. J. Peisl, T. J. Pole, A. J. Rossouw, R. G. B. Skirving, G. S. Schwartz, K. Stee1e, H. A. G. Slater, A. Taylor, B. A. Thomas, P. L. Vaughan, D. T. Watt, W. Wilson. Nineteen Associates including R. K. Briggs, S. I. Du Preez, P. G. Gaylard, P. H. Hartslief, W. M. Mackay, A. D. Ross. Three Students: V. S. Care, R. J. Drummond, P. J. Pretorius. Thirty-one Visitors including C. P. S. Barnard, D. W. Bosch, M. Bain G. L. Brown, G. D. Behrens, C. Coetzer, D. M. Gilbart-Smith, R. L. Man, Dr G. J. Stander, M. W. L. Steinobel, R. H. E. Thorpe, T. D. van Wyk, P. H. van Zyl, E. Vereecken, J. J. H. Viljoen. Secretary, D. C. Visser. Total present: 215. OBITUARIES The President: "It is my sad duty to announce the death of the following: Bruce Donaldson Crawford, Fellow, who joined the Institute in 1951 and passed away on 29th April, 1970. Donald Joseph Powrie, Life Fellow, who joined the Institute in 1935 and passed away on 22nd July, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Associate: WiIliam Norman Carter. Students: Roman Michael Dabrowski, Sean George Dean Eaton, Alan Philip Stonham Howard, Anton du Preez Roos, Richard Harold Tourle. MEMBERS TRANSFERRED TO A HIGHER GRADE From Graduate to Member: Terrance Alexander Ward. From Associate to Member: Bernard Andre Thomas. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade." CO-OPTION The President: "I wish to advise members that, in terms of clause 3.9 of the Constitution, Mc. H. P. Carlisle had been co-opted to serve on Council." PAPERS FOR PRESENTATION The President: "We have two papers today, and I am first going to call on Dr Stander the Head of the Water Division of the C.S.I.R., who IS well known to many of you for his work and talks on pollution, who has had more than a little to do with this industry, and who has been I would say, of the greatest possible assistance to the mining industry in overcoming the problems of pollution which are so prevalent in industry of this nature. He, Mr Henzen and Mr Funke have written this paper, 'The disposal of polluted effluents from mining, metallurgical and metal-finishing industries, their effects on receiving water and remedial measures.' This is the Water Year, as you know, and it is most appropriate that we should have such an authority to talk to us on this very important topic. I now have much pleasure in asking Dr Stander to introduce his paper." After the presentation of the paper the President said, "Gentlemen, I am sure that you would like me on your behalf, to thank Dr Stander very sincerely for a paper which I think has enabled us to get a completely new slant on the Water Year. There are many people who have put their finger on this campaign and said, it is all a gimmick. There are others-I suppose notably some of the bridge clubs which operate on week-day afternoons in Parkview-who seem to think that this is a quick way of getting early rain. Of course, it is not. This is a most important paper which we have had given to us this afternoon. You probably found it here when you arrived and have not read it-I was very lucky to be able to read it last night, and there is an awful lot of meat in it. For as long as I have been associated with mining in any way, there has been a problem of polluted effluent-of effluents carrying a mineral load from mining, and I think Dr Stander is absolutely right-and, of course, the Commission is right when they say that this is not merely the problem of mine management or mine owners-this is a problem which affects every single human being in this country.

Mr G. Maude was educated at Huish's Grammar School (Taunton) and Leeds University. He graduated in 1961 with a B.Sc. degree in Mining. Mr E.B. Crocker was educated at Florida Park High School, Witwatersrand Technical College, and the University of the Witwatersrand.

Jan 1, 1985

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By P. Schutte

It is evident from most admired companies, globally, that they drive key priorities such as teamwork, customer focus, fair treatment of employees, initiative and innovation into their organisations. It is clearly proofed in all the research that the role of the human factor, and therefore human behaviour, is pivotal to companies striving to accomplish goals such as competitiveness, customer delight, high quality, growing productivity as well as a safety-committed work force. The challenge of leadership is to change the worker’s poor perception of safety to an excited, empowered, valued employee who is continuously committed to the achievement of high levels of health, safety and conformance – the challenge therefore is to transform from within. Any work force needs a set of behavioural rules which work for it – including safety rules and critical safety behaviours, which are accepted through involvement leadership, encouragement and support.

Jan 1, 2003

By N. B. Strydom, P. L. Jooste, H. F. Kotze, W. H. Van Der Walt

Note: A revised method of heat acclimatization by N. B. STRYDOM, W. H. VAN DER WALT, P. L. JOOSTE, and H. F. KOTZE INTRODUCTION Climatic-room acclimatization was introduced in the gold-mining industry in 1965 and was rapidly adopted by all mines because it reduced the number of days required for heat acclimatization from 12 to 8. The method has been adequately described in previous papers1, 2 but, briefly, requires four hours of heat exposure per day while the work rate is progessively increased from 35 W on Day 1 to 70 W on Days 7 and 8. Several attempts to shorten

Jan 6, 1976

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

DD3-tunnels (PD BH's) ? Rotary coreholes 111no. (124) ? Percussion holes Ono. (37) ? Sampling (rock and soil) ? Soil and rock permeability ? testing ? BH Televiewer Surveys [ ]

Jan 1, 2007

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V, Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By use of a finite-difference model of an experimental galvanic cell, the effect of a resistance in the metalic conduction path on the potential and current distributions in the cell was predicted. The model predictions were compared with experimental measurements of potential profiles (measured by use of a scanning reference electrode) and galvanic currents. The predictions agreed well with the experimental measurements. Apart from this model, which is applicable in macroscopic cells (Le. with an electrolyte of low conductivity), a calculation procedure was developed to predict the effect of an external resistance on the galvanic current in a microscopic cell (high conductivity). The responses of the galvanic currents in the microscopic and macroscopic cells to changes in the external resistance were compared. From the similarity of the responses, a simple practical procedure for the evaluation of the external resistance (meter resistance) that can be tolerated is proposed.

Jan 1, 1989

By C. M. G. Wortley, N. Randolph, I. Ralston, R. D. Beck

The ?AMIRA Metal Accounting Project? had its origin in a workshop held in Cape Town on 1 August 2001, with the title ?Challenges in Metal Accounting and Information Management?, which was organised by the Western Cape Branch of the South African Institute of Mining and Metallurgy. This workshop identified the lack of an accepted set of standard procedures for metallurgical accounting as an industry-wide problem. Discussions which followed this workshop led to the initiation of the AMIRA Project P754, ?Improving Metal Accounting?, in 2003. The primary objective of the project was to provide tools for improving the auditability and transparency of metal accounting from mine to product and to facilitate good corporate governance. The planned deliverables of the project were a series of research projects into aspects of metal balancing in different types of metallurgical operations, a Code of Practice on Metal Accounting, and a textbook on the subject which could serve as a guide for metal accounting practitioners and students studying the topic. An additional planned deliverable was the provision of a new variety of professional experts in metal accounting, through successful completion of the research projects. Researchers were engaged at the Universities of Cape Town, Queensland and Stellenbosch and the project was sponsored by five mining companies, including three of the largest global mining groups. Research Program Eight research projects were undertaken as part of the P754 project and these are described briefly here to indicate the scope of the project. University of Cape Town ?Development of a methodology for measurement network design for metallurgical accounting at Namakwa Sands?. This project was based on the Namakwa Sands Separation Plant, with a data rich environment, and involved the investigation of measurement network design through the use of heuristics and the analysis of complex processing circuits. An industry-wide survey of current practice to facilitate the development of an expert system for plant accounting measurements was carried out. ?Metallurgical accounting design at the Waterval UG-2 Concentrator?. The objective of this project is to develop a model for predicting metal recoveries from the different components of a blended ore feed to a plant. ?Optimal measurement network design for metallurgical accounting at Zincor?. This project provided a hydrometallurgical test case for the design and evaluation of a semi-automated optimal measurement network. University of Queensland ?Quantifying the relationship between mine and mill?. This project involved a case study at North Parkes Mine, in which copper and gold ore is tracked from the pit source to the product, as well as a stockpile modelling study. University of Stellenbosch

Jan 1, 2007

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By F. H. Deist, M. P. Roberts

"The Collieries Research Laboratory of the Chamber of Mines of South Africa is developing a coherent system of programs to aid in the full spectrum of activities arising in the planning of new as well as operating mining enterprises. It is the purpose of this paper to describe the design and application of two subsystems in the complex.One of these subsystems is an initial version of a production simulator. This program draws upon a model of a mining enterprise and simulates the operational and financial aspects of a set of alternative mine production plans.These plans are specified in terms of proposed sequences of operations. Details such as reserves, production rates, resource requirements and so on, are taken from the model.Physically, the model takes the form of a cross-referenced data base, maintained by means of a general file maintenance system which is another subsystem described.The paper concludes with a description and analysis of the first practical application of the two programs."

Jan 1, 2014

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser, T. Schirmer

At a time of resource consumption, it is important to study the chemical composition of mining and metallurgical wastes to prevent the dissipative loss of metals and metalloids from the mining value chain. In particular, the recovery of critical elements from wastes is an option to increase the resources of such materials that are economically significant and have an overall supply risk. In this paper we report on the chemical composition, in particular the critical element content, of granulated slag originating from historical smelting activities in the Tsumeb area, Namibia. Laboratory-based inductively coupled plasma–mass spectrometry (ICP-MS) and X-ray fluorescence (XRF) analyses as well as portable X-ray fluorescence (pXRF) demonstrate that the slags are on average enriched in base metals (Cu 0.7 wt%, Pb 2.7 wt%, Zn 4.7 wt%), trace metals and metalloids (Cd approx. 50 mg/kg, Mo approx. 910 mg/kg) as well as critical elements (As approx. 6300 mg/kg, Bi approx. 3 mg/kg, Co approx. 200 mg/kg, Ga approx. 100 mg/kg, In approx. 9 mg/kg, Sb approx. 470 mg/kg). While metals and metalloids such as As, Mo and Pb can be determined reliably using pXRF instruments, the technique has inherent limitations in evaluating the contents of certain critical elements (Ga, Sb). However, there are positive correlations between the As, Mo, and Pb contents determined by pXRF and the Ga and Sb contents obtained through ICP-MS and XRF. Thus, quantitative pXRF analysis for As, Mo, and Pb allows calculation of Ga and Sb abundances in the slags. This work demonstrates that pXRF analysers are a valuable tool to screen smelting slags for their chemical composition and to predict the likely contents of critical elements.

Mar 1, 2021