Search Documents

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By Jogeshwar P. Singh, Ahmed AlaaEldin, Mohamed Ashour

The presented methodology allows the determination of the response of laterally loaded battered long piles in sandy soils based on the soil-pile interaction. The Strain Wedge (SW) model which was originally developed for laterally loaded vertical piles is modified to assess the behavior of laterally loaded battered piles with the consideration of soil and pile properties. The method predicts the pile-head response and associated p-y curves. The presented soil-pile model accounts for the variation of the direction and magnitude of the batter angles from the vertical position. Unlike current practice, the proposed technique also provides the p-y curves for battered piles in sandy soils based on soil and pile properties (i.e., sand relative density, friction angle, pile geometry, etc.). The proposed methodology has been validated through a number of comparisons with full/model-scale pile load tests. INTRODUCTION The influence of pile battering on the lateral response of piles is rarely studied in the literature. Over the last decades and as suggested by Kubo (1962) and Zhang et al. (1999), a p-y multiplier is applied to predict the response of laterally loaded battered piles from an equivalent vertical one. Several researchers conducted model-scale piles load tests to understand the behavior of battered piles subjected to lateral load (Juvekar and Pise 2008; Meyerhof and Ranjan 1973; Meyerhof and Yalcin 1994). However, such tests were conducted on model piles with diameters less than 30 mm which may not have reflected actual soil-pile interaction. Battered piles are generally categorized as positive or negative battered piles according to the angle of pile installation as shown in Fig. 1. From the small-scaled and numerical models of battered piles, it was found that the lateral capacity of negative battered piles is larger than that of vertical ones. On the other hand, the positive battered piles have lower lateral capacity when compared to vertical piles (Fan-ren and Ji-Ming 2011; Juvekar and Pise 2008; Manoppo 2010; Reese et al. 2004; and Reese and Van Impe 2011).

Jan 1, 2018

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Y. G. Qin

In this article an experimental study of axial bearing capacity of half-closed steel pipe pile installed at BKSH dock is presented. In comparison with open and closed end piles, half-closed end pile is considered to have high bearing capacity and good penetration, that is, it not only has a capacity as twice as the same size open end steel pipe pile, but also has blow counts as half as the same size closed end steel pipe pile. It is economic to use half-closed end pile in soft ground without a deep deposit of thick stiff clay. This article also describes a large scale model pile test and preliminarily analyses mechanism of improvement of bearing capacity of half-closed end pile with emphasis on effect of squeezed soil on side friction; an empirical approach is presented in which side friction is related to density of squeezed soil and which is useful for reasonably chosing side friction of different types of piles in design of foundarion.

Jan 1, 2010

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By Rick Piovesan, Pramod Rao, Nihal Bohra, Mark Wahler

"This paper discusses the approach followed for the geotechnical design of 355 mm and 457 mm diameter driven open-ended steel pipe piles used for a gas plant at a green field site in Pilbara region in Australia. The principal bearing layer at the site comprises of calcareous Red Bed soils and weak rock, which is the typical geology along a significant length of the northern Western Australian coastline with carbonate content up to 70%. The uncertainty associated with the mechanical behavior of the calcareous soils and cemented soils (weak rocks) presented design challenges in the selection of appropriate pile design method and design parameters for pile capacity estimation during Front End Engineering Design (FEED). The American Petroleum Institute (API)-based design methodology was adopted. The representative design parameters for the Red Bed weak rock were established by treating the weak rock as clay with undrained shear strength as one-half of the characteristic unconfined compressive strength (UCS) value. Both statically load tested and CAPWAP (Case Pile Analysis Wave Program) estimated ultimate axial pile capacities on 25 early pre-production indicator piles demonstrated that the API design methodology for siliceous soils provides reasonable prediction of axial pile capacity in the red bed soils/weak rock and no reduction to API computed axial capacity due to carbonate content is warranted. The results also demonstrated that penalizing axial pile capacity solely based on carbonate content is not appropriate.IntroductionA gas processing facility was proposed to commercialize the gas reserves located 130 km offshore from the north-west coast of Western Australia (WA). The project site is a green field site located in the Pilbara region along the northwest coast of WA. Specific information regarding the site has been withheld due to confidentiality reasons. The site layout is shown in Figure 1.The site comprises low-lying tidal flats, clay pans and sand dunes covered with low scrub. The onshore site levels vary from elevation 1 m to 10 m AHD (Australian Height Datum), with the largest proportion of the area (excluding sand dunes) between elevations of 1 m and 3 m.The onshore facilities are to comprise a liquefied natural gas (LNG) plant site, a construction camp, the land-based portion of the materials offloading facility (MOF), roadways, and borrow pit areas.The existing ground levels within the process train area, where pile load testing was performed, vary from over 7 m AHD where the summits and peaks of the central dune exist to typically 1 m to 2 m AHD towards the east and west edges of the dune. The proposed finished grade for the process train is set at 7 m AHD."

Jan 1, 2015

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Claudio Olalla

This paper relates to the foundation of a steel structure located at the San Martin de la Vega (Madrid) amusement park. The structure has more than 100 supports with various loading conditions, including important horizontal and uplift forces. Additionally, the settlement tolerances are very strict. A massive gypsum formation with interbedded clay layers and random solution great voids at various levels constitute the soil. The foundation design has been conditioned large enough these difficulties (load conditions and soil problems). The piling machine used was powerful to drill through the soft rock (UCS up to 11Mpa). The integrity of each pile had to be guaranteed by continuous recording of drilling and concrete pouring parameters. In order to fulfil all those conditions, a STARSOL type-piling rig was used. More than 4500 meters of piles were performed. The diameters of the piles were 450 and 550-mm and their depths varies from 6 to 23 meters. All piles were reinforced over their full length.

Jan 1, 2002

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987