Search Documents

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By Timothy C. Siegel

A piled raft refers to a shallow foundation that is structurally connected to the piles, while composite ground refers to a soil-pile matrix where the piles are not structurally connected. The design objectives for both a piled raft and composite ground are (excluding special considerations such as expansive soil): (1) to provide a sufficient ultimate resistance and (2) to distribute the load into the soil-pile matrix so that the settlement experienced by the shallow foundation is within tolerable limits. A simplified model is proposed for a shallow foundation on composite ground where the foundation settlement is estimated as the sum of the downward movement of the piles plus the downward movement of the shallow foundation relative to the pile head. The proposed simplified model is applied using conventional geotechnical analyses for two hypothetical examples of shallow foundations undergoing compression settlement.

Jan 1, 2011

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By David J. White

The decreasing availability of land in urban areas, and the increasing demand for urban development is leading to the construction of taller and heavier buildings at increasingly marginal sites. Such structures usually require founding at depth and modern construction methods are making the economics of piled foundations ever more attractive (Salgado, 1995). However, the urban environment is not suited to pile driving. Conventional dynamic installation techniques (i.e. drop hammer or vibro-piling) induce vibrations and settlement in a zone close to the pile, and cause noise and dust pollution. Damage to existing structures resulting from pile driving vibrations is not uncommon (Tomlinson, 1986).

Jan 1, 2000

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

By Tracy Brettmann

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2001

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By F. Schlosser

The extension of Montparnasse Station in Paris required the construction of supports of very high unit capacity to support a particularly rigid super-structure. The majority of the site is characterized by the existence of old limestone quarries at a depth of approximately 20 metres. These workings have been backfilled in some places, have collapsed in some places and have given rise to local subsidences in the marne layers above them. This paper addresses the steps taken by the group of companies and their consultants to evaluate the equivalent stiffnesses of the supports necessary for the design of the superstructure, and gives details of the construction techniques chosen by the foundations specialist to adapt to the particular conditions encountered on this site.

Jan 1, 1989

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013