Search Documents

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991

By Noel Billette, Jean-Luc Chouinard

"An analysis of the number of industrial injuries shows that the mining sector is particularly affected, since mining is one of the most dangerous industrial activities in Canada. This has led to numerous inquiries, and supports the need for an in-depth study aiming at the identification of factors responsible for these accidents. One possible factor often pointed at is the small crews incentives and this paper presents a scientific approach applied to check a potential link between bonus and accidents at two mining companies located in northwestern Quebec.The data required to do so were the accidents, the salaries and the number of hours worked at each mining site by the hourly paid personnel for the period from June 1979 to January 1982. The analysis of the results derived from the initial information shows different behaviours of the frequency rate vs the bonus rate at these mines. The number of days lost per accident is independent of the bonus rate at both mine sites, as shown by Khisquare tests on contingency tables.IntroductionA wide variety of opinions has been pinpointed by a survey of the literature related to individual or small crew incentives and industrial accidents in sectors of activity where it applies. In addition, various formulae of mining contracts take place in the industry on one part, and statistics from this sector indicate a high accident frequency rate on the other part. These fact s have lead to this scientific investigation which does isolate the direct impact of the bonus on workers' accidents. This study was undertaken with the full support of the Quebec Metal Mining Association.The conclusions of this preliminary phase of the researchproject are presented for two mining complexes in northwestern Quebec. The procedure is somewhat similar to the approach of the Belmoral Commission, with the underlying assumption that bonus has a direct impact on accidents."

Jan 1, 1986

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By Jürgen Antrekowitsch, Gerardo R. F. Alvear Flores, Mehmet Ayhan, Christoph Zschiesche

Synergies between copper and lead extractive metallurgical processes enable the processing of a broad range of polymetallic materials. However, this complexity also brings some challenges expressed in terms of complex intermediates and final products. For instance, based on the limited solubility of Cu and Ni in crude lead bullion additional phases will appear during the crystallization of the melt. Beyond the need for continuous optimization of metallurgy the control of phase solidification is a further important pillar to achieve a more efficient process by minimizing the amount and cycles of reverts. This paper describes the microscopy study of one of the most relevant intermediate in the Cu and Pb metallurgy, the Cu based alloy and highlights the importance of applying a well-controlled cooling sequence to improve the overall process efficiency. INTRODUCTION One of the key aspects in Aurubis’s 2025 vision is to move towards the implementation of a multi metal recovery strategy. The implementation of this new multi metal vision is supported by the long tradition of the company, founded in 1866 as Norddeutsche Affinerie, and further developed by adopting modern copper smelting and lead smelting technologies for the processing of primary and secondary materials. The combination of these assets have already build the basis for processing of complex materials in the copper and lead circuits implemented in Aurubis’s facilities. The addition of a new smelting facility, will enhance these capabilities. Aurubis current flowsheet combines Cu, Pb and Zn metallurgy. This includes primary smelting of copper concentrate, processing of secondaries (residues, slimes, slags) and recycling materials (scrap, shredder material, e-scrap). These broad range of materials contain not only the mentioned base metals but also a number of minor metals that requires to be properly managed to ensure efficient recoveries and quality of the targeted metals.

Jan 1, 2019

By Robert B. Parsons

"Canadian income tax legislation contains a number of provisions which serve to facilitate the structuring of business arrangements, including mineral resource ventures. These rules are often fairly complex and not easily understood. This article attempts to explain in plain and understandable language the mechanics and benefits of one of the more frequently encountered provisions, the ""Section 85 election"".IntroductionThe Canadian resource industries are probably singled out for more special attention under this country's tax legislation than any other industry. This special treatment is, of course, not always welcomed by the industry, such as where unnecessarily restrictive taxation is perceived to exist or where agonizingly complex tax legislation must be dealt with. On the other hand, certain provisions in the tax legislation treat the industry in a relatively favourable manner, including a number of rules which, in recognition of the high risk and capital requirements of the resource sector, serve to facilitate the structuring of resource ventures."

Jan 1, 1984

By A. B. Carino

Gulf Minerals (Canada) Limited's Rabbit Lake uranium operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and /34 miles northwest of Lynn Lake, Manitoba. The paper follows the ore flow through crushing, grinding, sulphuric acid leaching, countercurrent decantation, solvent extraction, ammonium diuranate precipitation, thickening, drying and tailing neutralization.

Jan 1, 1979

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By Jeffrey S. Loen

"The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 x thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By R. A. Horn, S. M. Telfer

"Canada has a per capita GDP second only to Japan among the G7 countries and a positive trade balance which ranks third among the world's major economies. International trade represents a very large part of the national economy and as a proportion of GDP is larger than that of all the other G7 countries with the exception of Germany. On the negative side the Canadian current account deficit relative to the size of the economy is significantly worse than that of all major industrial countries, due mainly to the cost of servicing an immense foreign debt and to a large and worsening negative trade balance in manufacturing.The outflow of money may be reduced by increasing the productivity and competitiveness of those sectors of the economy in which Canada already has a leading competitive position and which have the potential for further growth. The mining industry is uniquely qualified in this respect in that Canada is the western world's largest producer of metals and mineral products and has the geology and the exploration skill to replenish reserves assuming that an adequate level of investment is maintained. In 1989 the minerals industry contributed $8 billion to the country's balance of payments and with the exception of forestry is the only sector of the economy which has shown consistently increasing foreign earnings over the long term.In recent years there has been a decline in exploration in Canada and a significant increase in countries such as Chile. The demand for hard currency to finance the development of the newly emerging capitalist economies of the CIS and Eastern Europe is also driving these countries to seek foreign investment to allow them to exploit their natural wealth more efficiently. Canada is therefore facing growing international competition for risk capital and in the future its trade surplus will probably decline in the face of lower cost foreign production.Canada rightly exercises a high level of environmental control on its mining operations; however a significant deterrent to investment is the fundamentally unjust application of the many provincial and federal environmental laws, under which a mining company, even if it takes every measure to protect the environment, runs the risk of eternal and unlimited future liability. If this situation is not rectified the effect will be an increase in global pollution as mines in countries with more lax application of law and regulations controlling environmental damage replace those of Canada. Tax benefits and incentives are a more efficient means than arbitrary regulations in minimizing environmental damage."

Jan 1, 1994

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By Barry James

"This paper discusses past and current energy use patterns in the mining and manufacturing sectors of the industrial minerals industry. Information is presented on the primary energy input types as purchased by the industry, the quality and form of the energy actually required by the various production processes, and the residual form of this energy, either embodied in the product or rejected in gaseous and liquid waste heat streams. With the continuing concerns about the availability of energy combined with the rapidly increasing cost of energy as a production input, the reduction of energy usage through improved efficiency will undoubtedly be an increasing priority for the industry during the 1980s. Reduced energy consumption through investment to improve energy efficiency appears to be advantageous from both the corporate and national perspectives.IntroductionEnergy, like labour and materials, is one of the basic production input s to the various mining, processing and manufacturing production stages in the industrial minerals industry. Energy costs, as a percentage of total production costs, have been well above the average for industry in Canada, accounting for more than 50 cents out of every dollar in the most extreme cases. Consequently, energy has always been a relatively important management concern in the industrial minerals industry.The energy supply and price situation in Canada and internationally has been changing rapidly since 1973, following a long period characterized by declining real energy prices and an abundance and wide choice of energy supplies. It is generally accepted that energy prices will continue to increase rapidly, and that there will be uncertainties about the long-term continuity of supply of some energy types. In essence, a period of relative stability has been replaced by a period of relative uncertainty. In such a changing situation, a reassessment of the role of energy as a production input is appropriate.The following sections outline some of the effects of the changing energy scene on the industrial minerals industry. These effects are dealt with primarily in terms of energy costs, because, in most circumstances, a change in the cost of energy as a production input is the end result of both energy price and energy supply changes."

Jan 1, 1981

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By Mel Owen, Bob Tipman

"A number of studies have identified the presence of heavy minerals in the Athabasca oil sands. A 1996 Mineral Development Agreement study into the recovery of Co-Products identified low operating costs, a simple flowsheet and access to market as key drivers in advancing interest in a viable project.Commercial bitumen extraction processes recover 50% of the titanium heavy minerals and 85% of the zircon into froth containing 1 % of the feed solids. Froth treatment tailings grade is 11.5% Ti02 and 3.6% Zr02.Processing this high grade feed in a combination of flotation, roasting, screening, gravity concentration and magnetic separation, results in concentrates of rutile, leucoxene, ilmenite, zircon and rare earths of marketable quality.A combination of high grade feed and a simple process lead to operating costs among the lowest in the industry. Low cost heavy minerals and low energy costs indicate an intriguing potential for low cost pigment production in Alberta. The production of heavy minerals from oil sands remains one of the largest untapped resources in the Province of Alberta1.0 IntroductionThis paper describes the results of an investigation into the recovery of heavy minerals from tailings produced by the major oil sands plants. The study was carried out under a Canada-Alberta Mineral Development Agreement (Alberta Chamber of Resources 1996). The MDA Co-Products Study examined the potential for the economic recovery of heavy minerals from oil sands tailings."

Jan 1, 1998

By John E. Callahan

"A stream sediment geochemical survey covering an area of 13.000 sq. km near Churchill Falls. Labrador. was conducted for Brinex (British Newfoundland Explorations Ltd.) prior to partial flooding by the Churchill Falls power project. Stream sediments (minus 80-mesh) were analyzed for Cu, Pb, Zn, Ni, Ag, Mo. U and Mn, and the heavy mineral, nonmagnetic fraction (minus 60-mesh) for Cu, Pb, Zn, Ni, Ag, Mo, Ba and Mn. A binocular examination of the concentrates for sulphides and pyrope garnet was done on the heavy mineral concentrates. The concentrates were also examined for fluorescent minerals.Two distinct areas with high trace-element values indicate the need for follow-up studies. The first is in an area of gabbro erratics containing massive and disseminated sulphides (pyrrhotite, pyrite and minor chalcopyrite) on the western edge of the survey area along the Esker Road. The second, largest area (several hundred square kilometres) is anomalous in U and Mo and associated with felsic intrusives (Red Wine Complex?), syenites. granite gneiss and sedimentary rocks (Seal Lake Group?).The binocular study showed that almost 15% of the heavy mineral concentrates contained pyrite and no other sulphides. This indicates that this technique may be worthwhile in determining the presence of sulphide minerals in stream sediments from glaciated environments. The only fluorescent mineral observed in the study was zircon."

Jan 1, 1981

By M. Sutherland

"Increased efforts to improve mine safety have led to various successful forms of ground control in Canadian underground mines. At Inca Limited's T-3 Mine in Thompson, Manitoba, a perimeter blasting method has been implemented in jumbo drilled development headings.The technique utilizes an increased number of perimeter blast holes in the drill pattern while decreasing the linear charge density of explosives in any individual perimeter hole. The decrease in perimeter charge density means less blast damage to the surrounding structure.The benefits realized include increased safety through less loose ground and substantially less scaling time, less overbreak and improved long-term drift stability. This paper highlights the development and implementation of the perimeter blasting program.IntroductionThompson Mine Thompson Mine is a 6000 ton per day underground nickel mine located just outside the city of Thompson, 400 miles north of Winnipeg. The mine is serviced by the T-I shaft and by the T-3 shaft. The shafts are 10 000 ft apart and are connected on several levels with the deepest operating levels at T-1 and T-3 being 4000 ft and 2400 ft respectively.The T-3 Mine presently produces 52% of the total Thompson Mine production and 65070 of the 3000 ft of mine development each month. Current development of the 5 million ton 1, C orebody below 2400 level at T-3 will maintain these production and development ratios.Depending on equipment requirements, development headings at T-3 Mine vary in size. The 1, C ramp, at 17 1/2 ft wide by 10 1/2 ft high, is presently the largest development heading at T-3. Fifty- two per cent of the development footage is done with four Gardner Denver two boom electric /hydraulic jumbos and one Gardner Denver one boom electric /hydraulic jumbo. The remaining 48% is driven with hand-held jack-leg drills."

Jan 1, 1990

By Tomoya Kawasaki, Tatsuya Motomura, Yutaka Yasuda

Saganoseki Smelter, one of the largest copper producers in Japan, currently operates a single flash smelting furnace to produce 450,000 tons of new copper annually. The smelter used to employ two flash furnaces, and integrated the two into one in 1996. Since then, various improvements to its facilities and technologies have been made to increase productivity. To upgrade the operation efficiency, "stability" was considered a key issue, and the measures were taken to increase the operation and facility reliability. Currently, the furnace is running at a feed rate of 215 DMT/h, while the furnace utilization has been maintained at 97%. This paper outlines recent improvements that have made to increase furnace productivity and efficiency.

Jan 1, 2014

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982