Search Documents

By D. F. Hambley

"In designing are passes f or underground mines specific consideration should be given to unimpaired flow of broken rock, the dump point, and typical practices f or overcoming operational difficulties. Design features such as branches, bends, and knuckles should also be considered. This paper pro vides engineering information and various criteria for designing are passes, draw points. feeders, and support systems, together with several illustrative examples.IntroductionOre passes are the primary mean s o f vertical transfer of mined ore to the ore bins and loading pocket from which the o re is hoisted to the surface (Fig. 1) . While the words "" ore"" and ""ore pass"" are used here, such transfer systems ca n be used for any broken rock.The most extensive ore pass systems are found in caving and sublevel stoping mines. Extensive ore pass systems are also found in multilevel mines having steeply dipping orebodies. In more flat-lying orebodies , ore pass systems are sometimes used in conjunction with conveyor systems .Two decades have passed since the principles of the flow of bulk solids were formulated (Jenike, 1961, 1964; Johanson and Colijn, 1964; Kvapil , 1965). However, few published papers are available that discuss the design criteria for ore pass systems. Therefore, the aim of this paper is to provide the information necessary for good o re pass design .Rock Flow in Ore Pass SystemsIf an ore pass system is to fulfill its function, the transfer o f material must occur in an orderly fashion and in such a way that the full size of the opening is employed effectively. Apart from un controlled flow at the drawpoint, or outlet , whose design will be considered later in this paper, two occurrences may impede flow in an ore pass, namely:• Hangups due to interlocking arches.• Hangups due to cohesive arches.Prevention of each of these problems will be discussed in succeeding sections of this paper. A third problem piping, is related to the ratio of the drawpoint size to the o re pass size and will be discussed under drawpoint de sign."

Jan 1, 1987

By Neil Schofield

"The Pine Creek gold mineralization is associated with saddle reefs and quartz and quartz sulphide veining within the Enterprise Anticline. The anticlinal structure is complex and the mineralization was considered prior to development to be dominantly strata controlled. Gold grades vary up to 160 gin 1.5 m core samples with coefficients of variation in excess of three.The estimation of ore reserves for such a deposit must account for both the geological complexity and the extreme variability of gold grade.This paper describes the structural and variogram analysis of the gold grades and demonstrates the importance of incorporating the geological model in such an analysis. Variogram interpretation is greatly improved and greater insights into the finer geological structure areprovided. Part 2ofthis work presents the application of multigaussian kriging to reserve estimation for deposits with highly variable grade and which consequently demand highly selective mining operations. IntroductionThe Enterprise Gold Mine is situated some 220 km southeast of Darwin in Australia's tropical north. Gold is believed to have been discovered there in 1869 during the construction of the overland telegraph line.From 1894to 1915, some 75 000 ounces of gold were produced from 121 000 tonnes mined mainly by Chinese leaseholders. From 1906 to 1915, government-sponsored drilling led to the sinking of the Enterprise Shaft to 79 m and several drives were developed. Mining ceased because of war.Since late 1980, Goldfields Exploration Pty. Ltd. had explored on several mining tenements near Pine Creek under joint venture with the title holders, Enterprise Mines NL. This work culminated in the development of the current mine which opened on October 29, 1985.Feasibility studies to determine the economic viability of mining were based on ore reserves generated by project geologists using a sectional polygonal approach tuned to the interpreted geological control of the mineralization.The study motivating this two-part paper covers are-estimation of the recoverable reserve s using the geostatistical approach of multigaussian kriging developed at Stanford University, (Verly, 1984)."

Jan 1, 1988

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By D. S. Rogers

"Throughout the history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. Diamond drilling plays an important role in the evaluation of the stratigraphic and structural features which control ore deposition. The main function of diamond drilling is to locate favourable areas of mineralization.To date, over 20,000 diamond drill holes have been drilled from combined surface and underground programs. Needless to say, a great many significant intersections, carrying a wide range of gold values, have resulted from the total of over 756 miles of drill cores which these programs have produced.However, the term ""significant"" takes on new meaning in light of the experience of diamond drilling in a number of ore-type situations at the Dome Mine. Drilling through individual ore veins, such as the Fuchsite Vein or the Quartz-Tourmaline Vein, often intersect the vein structure; however, assays from the veins frequently fail to yield any ore grades. Similarly, drill cores through stringer-type occurrences such as dacite or conglomerate, when assayed, fail to indicate the true size or grade of the orebody ultimately mined.IntroductionOver the years, those who explore for gold and those who have the slightly less fickle task of actually mining gold have shared a common dilemma. That dilemma lies in the failure to relate the results of diamond drill information to a positive ore situation, or ultimately to reconcile ""diamond drill indicated ore"" to actual ore reserve tonnages.Drawing on the knowledge of more than 72 years of mining history at the Dome operation in the famous Porcupine Camp, this paper will review a number of drift and stope situations in which the grades of the ore material extracted will be compared with the anticipated grade of that same drift or zone as calculated solely on the basis of diamond drill assays."

Jan 1, 1982

By J. W. M. Porritt, M. P. Brameld, R. H. McCorkell

"Soil-gas Rn was measured by two types of alpha-particle-track detectors, by emanometry and by counting alpha-activity on Rn-decay-product collectors. Soil samples were analyzed for V by fluorimetric and fission-track methods, their Rn-emanation by decay-product collectors and their total alpha activities with track detectors. The same uranium anomalies were revealed by each method. Fission-track analysis of leaves for V showed only random variations with sampling site, and the Rn emanation of trees and leaves removed from them was barely detectable . The agreement among the other methods is significant, total alpha and collector methods are simple, rapid and useful, and a combination of methods at a site would reveal disequilibrium in the U-decay series if present. Track-Rn measurements are highly reproducible and insensitive to apparatus design and their sensitivity is not enhanced by covering the detectors with thin foil or placing them in large containers.IntroductionIn the past two years , a number of methods of geochemical exploration for uranium have been tested by the authors over the known copper-uranium occurrence at South March, Ontario. This was done partly to compare methods and partly to develop and test new ones. The South march deposit has been described a number of times by others(1,2,3,4). The methods included in this study were the following.Emanometry, Radon in soil gas is measured by pumping the gas into the cell of a scintillation counter or emanometer(5,6). Alpha particles from radon (222Rn) and its decay products (218Po and 214Po) produce scintillations of light in the silver-activated zinc sunphide (ZnS(Ag) covering the walls of the cell. These are counted by a photomultiplier tube and scaler, the count ra sulphide (ZnS(Ag) covering the walls of the cell. These are counted by a photomultiplier tube and scaler, the count rate being proportional to the concentration of radon in the soil gas."

Jan 1, 1981

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By Michael T. G. Brown

Syncrude Canada Ltd. has recently completed construction of its ambitious tar-sand mining and processing facilities at Mildred Lake, Alberta. The Syncrude site is approximately 48 km (30 miles) north of Fort McMurray near the west shore of the Athabasca River. The Syncrude operation involves the open-pit mining of approximately 270,000 tonnes (300,000 tons) of tar sand daily using draglines and a conveyor system. Bitumen is extracted from the tar sand, upgraded to oil-gas and transported to refineries in Edmonton and other locations for final processing . The Beaver Creek Dam forms part of the mining facilities for the Syncrude tar-sand mining operation. Water from Beaver Creek is diverted from the open-pit mine site south to the Athabasca River via Ruth Lake and the Poplar Creek Dam. General site layout is shown on Figure I . Design of the dam was completed by R. M. Hardy and Associates Ltd. of Edmonton, Alberta (now Hardy Associates (1978) Ltd) . Construction was undertaken during the summers of 1974 and 1975 under the direction of Canadian Bechtel Limited, managing contractors for Syncrude Canada Ltd. Total length of the dam is approximately 2.8 km (1.7 miles), with a maximum height in the order of 16 m (50 ft) The Beaver Creek Dam is located in a broad, flat, poorly drained valley. About 50 per cent of the site is covered with treeless peat deposits, which ranged in thickness from in excess of 5 m (15 ft) at the east end of the dam to less than 1 m (3 ft) at the central portion. The peat deposits overlie Pleistocene meltwater sediments on top of clay/clay shales of the Clearwater Formation and the tar sands of the McMurray Formation. The peat deposits and high groundwater levels at the site combine to make the excavation and construction of a conventional rolled clay cutoff impractical. For these reasons, the slurry cutoff trench technique was utilized to produce an efficient and effective seepage cutoff under various sections of the Beaver Creek Dam .

Jan 1, 1979

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta's sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region's gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton's current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton's current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By Bruce C. Fielder

"The concentration of uranium in orebodies discovered in the Athabasca Basin of northern Saskatchewan over the last 20 years has increased by a factor of 100. These high grade uranium orebodies are associated with high concentrations of radionuclides, complex mineralogy and an elemental makeup that includes base metals, arsenic, and molybdenum. Exploiting these high grade ores has required metallurgical advances in milling, tailings disposal and effluent treatment as well as changes in the design of uranium mills.This paper describes the most significant advances, including advances in dealing with the environmental issues which have become more prevalent in recent years. The milling processes of the Cluff Lake Mill, Key Lake Mill, Rabbit Lake Mill, and McClean Lake Mill are compared to illustrate both similarities and differences necessary for milling different orebodies.BackgroundUranium mining in Saskatchewan started in 1953 when the Beaverlodge Mine, owned by Eldorado Nuclear Limited (Eldorado), came into operation at Uranium City. Development in the Athabasca basin started in 1975 when the Rabbit Lake mine came into operation. This was followed by the start-up of the Cluff Lake mine in 1980 and the Key Lake mine in 1983. The McClean Lake mine is forecast to start up in the near future. The McArthur River mine recently received construction approval and the Cigar Lake Project and the Midwest Project are currently in the environmental approval process.The Beaverlodge operation ceased production in June 1982 after nearly 30 years of operation. The Rabbit Lake mill processed Rabbit Lake ore from 1975 until 1985, Collins Bay R-Zone ore from 1985 until 1993, and is currently processing ore from the Eagle Point mine (Bharadwaj, Jarvi and Lam, 1996). The Cluff Lake mill processed ore from the D- Orebody from 1980 until 1984. Since then the Claude orebody has been processed and the OP and DS orebodies are presently being milled (SRK. Senes and Melis, 1987; and Cogema Resources Inc. 1994 ). The Key Lake mill processed ore from the Gaertner ore body from 1983 until 1989 and Deilmann ore has been processed since (Cameco Corporation, 1992b and I 994a). Processing of McArthur River ore in the Key Lake mill is scheduled for 1999. The McClean Lake mill will be processing ore from the JLR, Sue and McClcan orebodies associated with the McClean Lake mine. In future ore from the Cigar Lake and Midwest projects will be processed in the McClean Lake mill. (Minatco Limited. 1991a)."

Jan 1, 1998

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By Julio E. Claudeville

Approaches and Lessons Learned ??Address business needs?local skills training and employment ?local procurement programs ?health and safety programs ??Ensure consultants/ advisors/ contractors apply Company standards ?especially in the field/ locally ?will not be differentiated from the Company itself

May 1, 2006

By G. W. McDonald

"The mineralogical studies done on Hope Brook ore samples indicated that a heap leach gold recovery process may be possible. In the metallurgicalprogram that followed, column tests confirmed this interpretation. A 9300 tonne demonstration heap leach test, in the late fall of 1985, reaffirmed laboratory results while identifying operating conditions that will have to be addressed in a production heap leach plan. Operating plans, gold recoveries and cost areas will be presented.Another important factor in a successful operation is the environment approach.LocationThe Hope Brook gold deposit is located 5 km inland from Cinq Cerf Bay on the south coast of Newfoundland. Port au x Basques is 80 km west and Burgeo 40 km to the east of Hope Brook. As there are no roads in the area, access to the site is by sea or air (Fig. I). The Hope Brook orebody is near the saddle of three watersheds flowing to Cinq Cerf Brook, Boat Hole Brook and Betty's Pond. Acceptable solutions to several environmental concerns can be obtained by using the relative sensitivities of these watersheds.The terrain at the site is generally rolling to hummocky with numerous small ponds separated with rock outcrops and patches of peat covering. Tree vegetation is sparse except in the sheltered areas around Couteau Bay and Cinq Cerf Brook. GeologyThe Chetwynd deposit is hosted by the Lower to Middle Ordovician Georges Brook Formation of the La Poile Group, a thick sequence of volcanic and sedimentary rocks.The Hope Brook Zone contains the largest concentration of gold found to date at Chetwynd. The zone occurs as an intensely silicified lens 100 m to 550 m long (average 400 m) by up to 60 m in width and forms the eastern portion of a more extensive, 4 km long , alteration zone trending at 053 degrees Az and dipping 70 degrees southeast.The Hope Brook Zone contains massive finely granular quartz, scattered blue quartz eyes, 3070 to 8% pyrite, minor calcopyrite and trace molybdenite. Barren silicification envelopes the gold mineralization. The zone is flanked to the southeast by a 200 metre thick aluminosilicate alteration zone and to the northwest by a 10 metre barren pyritic siliceous fragmental rock . The original lithology may be either a thick felsic pyroclastic sequence or a quartz porphyry sill that has been altered by hydrothermal processes. Silica flooding of the permeable host was accompanied by gold deposition."

Jan 1, 1989

By H. N. Tran, D. Barham

"A systematic survey of the appropriate literature in terms of phase equilibria and possible reactions involving deposits in Municipal Solid Waste (MSW) incinerators are analyzed particularly with respect to the theoretical first melting points of typical ashes and the possible presence of a liquid phase at the temperature of ash-metal interface. Conclusions are drawn on the basis of the possible presence or absence of various metal chlorides and sulphates in such situations, and their effects on the problems of fouling and metal corrosion. From preliminary results, it would appear that ZnCl2 is unlikely to be present in any molten phase which causes corrosion because it evaporates rapidly from such liquids. It would also appear that PbCl2 and, by inference, ZnCl2 will sulphate at relatively low temperatures if the flue gas contains SO2 and O2.IntroductionMunicipal Solid Waste (MSW) incinerators produce fly ash which deposits on heat transfer surfaces throughout the furnace, leading to corrosion and loss of energy recovery efficiency. Despite a massive amount of research carried out on the subject of corrosion in MSW incinerators, the problem of corrosion of heat transfer metal is still with us, and no definite over-all cause and effect relationship has yet been identified. In order to make a contribution to the eventual solution of this problem, the authors have examined the problem from the beginning, using their knowledge of fouling and corrosion problems in black liquor recovery boilers as a starting point.The incineration of MSW has been used for many years to reduce the volume of material sent to landfill (ash volume compared to raw waste volume), and, in most cases, to recover energy at the same time by raising steam The steam may be ""low- or high pressure/ temperature"" depending on its end use. The higher the steam pressure and temperature, the greater seem to be the problems with corrosion of heat exchanger metal, presumably because the metal must withstand higher surface temperatures.The chemical and physical composition of MSW is extremely variable, not only on a regional basis, seasonal basis, and day-today basis, but also on a minute-by-minute basis, due to the inhomogeneity of MSW. This makes it extremely difficult to define cause and effect relationships, because both cause and effect are transient in nature."

Jan 1, 1991

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By P. R. A. Andrews, R. K. Collings

"There are more than thirty-five deposits or occurrences of celestite in Canada, chiefly in Newfoundland, Nova Scotia, New Brunswick, Ontario and British Columbia. Deposits of economic interest are the Lake Enon and MacRae deposits in the Loch Lomond district of Cape Breton Island, Nova Scotia. Two Cape Breton deposits were operated from 1969 to 1976 by Kaiser Celestite Mining Limited, which supplied an upgraded celestite concentrate to an associated strontium carbonate plant at Point Edward, near Sydney.The MacRae deposit is of current interest because of its possible development for strontium carbonate production using the ""black ash"" process. This process involves chemical leaching, rotary kiln calcining with petroleum coke, washing and treatment with carbon dioxide.Celestite is the basic material used in the manufacture of strontium chemicals, principally strontium oxide, carbonate, nitrate, chromate, chlorate, chloride, sulphide and phosphate. Strontium chemicals, in turn, are used in the manufacture of glass and ceramics, in pyrotechnic devices, in the production of strontium metal and in other metallurgical applications. Recently, strontium ferrites have been introduced into permanent ceramic magnets."

Jan 1, 1991

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979