Search Documents

By C. J. Kerr

"A recent information sheet from the Mining Health and Safety Branch of the Ontario Ministry of Labour was sent to all Ministry inspectors and engineers. The subject title was' 'Two Brakes on a Hoist Carrying Persons"" and it quotes mining regulation 699, sub-section 206(i):No hoist shall be used for the transporting of persons unless it has a braking system consisting of at least two sets of mechanical brakes to stop and hold the drum for the shaft conveyance transporting the persons.The intent of the regulation is that each of these brakes is to be set so that, individually, they can safely stop the drum carrying persons and also hold the drum without movement with the maximum manload.This can be achieved in the following ways: Single Drum Hoist-one brake on each side of the drum, one brake on the drum, one brake on the pinion shaft, where disc brakes are used two separate disc brake assemblies on the disc. Double Drum Hoist, brakes on companion drum can serve as backup brake only pinion brake with one drum unclutched.Friction Hoist, one brake on each side of drum As new hoists can be manufactured easily with a two-brake system, attention will be focused on retrofitting pinion brakes to older hoists.A brake mounted on a pinion shaft is designed purely as an emergency brake in the event of main brake failure , controls malfunction, and power loss."

Jan 1, 1989

By D. Eriksen

Zero Emission Gas power, ZEG, is a novel concept where a high temperature solid oxide fuel cell (SOFC) is integrated with a reforming reactor producing hydrogen from natural gas through Sorption Enhanced Steam Methane Reforming (SESMR). The SOFC is used as a high temperature heat source for regeneration of the CO2-absorbent. Moreover, by using part of the produced hydrogen as fuel for the SOFC, the waste heat of the process is considerably reduced. Thus, the process has a very high thermal efficiency and produces both electricity and hydrogen from natural gas. In addition, a stream of pure CO2 is produced in the regeneration step and can be deposited or used commercially. Initial cost estimates indicate a cost of electricity and a cost of hydrogen well below today's prices. A small (1kWel + 1kW H2) demonstration set-up is under construction and experimental results and related research will be presented. This set-up comprises one 2.5kWth H2 SESMR-reactor (about 0.85 Nm3/h H2) operating batchwise with dolomite as the CO2-sorbent. The reactor developed is designed like a parallel plate heat exchanger where the mixture of sorbent and reforming catalyst is packed between the heat exchanging plates. The demonstration set-up includes a 1kW SOFC operating in a continuous mode. The set¬up will therefore demonstrate continuous simultaneous hydrogen- and electricity production, but cannot demonstrate simultanuous electricity- and CO2-production. The set?up is well equipped for on-line monitoring of gas composition, flows and temperatures. This important part of the demonstration set-up is developed and provided by Christian Michelsen Research (CMR). A minor part of the project is the development of a continuous circulating fluidized bed SESMR-reactor system and in another related project the focus is on the development of more suitable sorbents. In these two projects co-operation with University of British Columbia and Lousianna State University, respectively, is highly appreciated.

Jan 1, 2005

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985

By L. Tong

"The oxidation of Quebracho was evaluated by acid-butanol assay, which indicates depolymerization of Quebracho. Anthocyanidin, an oxidation product of Quebracho, is stable at 95?C for up to 2 h. The ionization, complexation, and oxidation properties of Quebracho were discussed. Complexation of metal-Quebracho occurs at ambient temperature. The formation of complex precipitates is influenced by the acidity of the solution. Temperature is another important parameter that influences the oxidation and the complexation of Quebracho. Quebracho-ferric complex precipitate forms at 90?C, 0.1 mol/L H2SO4. The formation of Quebracho-metal complex in the leach solution is a possible reason for the consumption of Quebracho. Quebracho molecules adsorption on the mineral surface is reduced by consumption of Quebracho, resulting in poor sulfur dispersing effect in the leaching process. INTRODUCTIONQuebracho is used as a sulfur dispersing agent (SDA) in the pressure leaching of zinc concentrate as stated in U.S. Patent No. 3,867,268 (1975). It prevents the zinc sulfide particles from being coated with molten sulfur, thus preventing the inhibition of the zinc leaching reaction. Recently, the sulfur dispersing effect of Quebracho was investigated in the oxygen pressure leaching of nickel concentrate. The oxygen pressure leaching of pentlandite can be represented by reactions 1-3."

Jan 1, 2012

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By I. Clauzier

"A new method of managing electricity to reduce costs andimprove profits is discussed. Before taking steps to better manage electricity, it is essential to understand the terms peak demand and energy and their effect on an electrical bill. Knowing how electricity is presently used in the plant is the important first step. This goes beyond knowing how much electricity is used at each time of day, the individual contribution of every plant process to the total plant load must be known. At this point, each process is ranked according to importance to production in order to identify possible savings opportunities. These improvements can then be implemented by simply improving operations or in some cases, through the use of an automatic control system. IntroductionIn today's competitive environment, controlling costs is becoming increasingly important. All costs associated with operation must be controlled in an effort to improve competitive position. Electricity is a cost component that can and should be managed.Although the term management can mean different things to different people, the intent is always the same: to make the best possible use of existing resources, whether labour, equipment or electricity.The simple approach to managing electricity presented in this paper consists of four steps.I. Understand Peak Demand and Energy. It is essential to understand the terms, peak demand and energy and their effect on your electrical bill.2. Know Your Present Electrical Use. The present use of electricity in the plant must be known. This goes beyond simply knowing how much is used at each time of day, to accurately knowing how each process is contributing to the total plant electrical load, and ultimately to the electrical bill.3. Identification of Savings Opportunities. With this information, energy savings opportunities for reducing the electrical bill and improving profits can be identified.4. Implementing Improvements. Having identified areas of potential savings, improvements can then be implemented in order of their significance. This could be a matter of simply improving operations, or in some eases may mean the use of an automatic control system.These four steps can result in significant dollar savings."

Jan 1, 1987

By David A. Fawcett

"This paper presents a summary compilation of current Canadian coal research projects in the areas of exploration, mining and preparation. The compilation forms the basis for a review of present operations and technology, and of current research efforts. General research areas, requirements and priorities are suggested along with a discussion on achieving the research goals in terms of funds, facilities and staff. The current level of research funding in these areas is assessed. IntroductionCanada's coal production is expected to undergo major expansion over the next two decades in response to domestic demands on coal for electrical power generation, industrial uses and conversion to synthetic .fuels, and in response to export demands for both thermal and metallurgical coal s. Surface mining will continue to dominate, but underground mining will contribute an increasing proportion to total production.In Canada, coal research, particularly in the areas of exploration, mining and preparation (E, M & P), has been limited. Increased impetus has recently been given to this research with expansion of CANMET's activities and with the establishment of the Coal Mining Research Centre (CMRC). University researchers are branching into coal research; strata mechanics and preparation are popular in mining-related fields.With the increase in number of organizations and individuals involved in coal research, a means of keeping abreast of the ongoing work is necessary. An annual summary of the status of and developments in current research assists in providing this information. The CMRC prepared such a summary for Canadian coal E, M & P research in 1979 and it received favourable response, justifying the effort. A 1980compilation has been prepared and pro vides the basis for this paper; it is presented with a brief discussion on background, format and content.The compilation forms a basis for an examination of the current status of Canadian technology in E, M & P and of the ongoing research in each area. General research requirements are reviewed and programs and tasks are suggested, followed by a discussion of research goals in term s of priorities and achievement. An assessment is made of the level of research funding in Canada, with comparisons drawn from the United States, the United Kingdom and Australia."

Jan 1, 1980

By W. D. Mulholland

"I ASSUME that any effort on my part to deal with the question of the importance of the mining industry is going to be largely an exercise in preaching to the converted, but there are one or two aspects that I'd like to particularly mention.The first is that, in terms of almost all factors, the mining industry is a very important industry in Canada. It is important in terms of employment in relation to the gross national product of Canada and it is particularly important in the international trade of Canada. So far from being insignificant domestically, it is also an extremely important factor in the international picture. That's an important point to bear in mind, because as we talk about all the other matters we never can lose sight of the fact that mining management always has to be conscious of its international competitive position. It is something that one forgets at one's peril, and to a somewhat greater extent than is true of many other industries, those managements have to compete in an international context for their markets, to some extent for their people for specialized skills and of course for finance. In the evolution of domestic policies it is a very, very perilous step to take to impair that competitive ability of the domestic mining industry."

Jan 1, 1972

By N. E. Nelson

"The Hidden Creek mine is about l~ miles north of the north end of Granby bay; a nearly landlocked body of water on the west side of Observatory inlet; 90 miles north of Prince Rupert; British Columbia.The main haulage way of the mine at 385 feet above sea-level has been driven north into the somewhat precipitous end of a north-south ridge that rises from the tide flats between the east and west forks of Hidden creek. The outcrops of the principal orebodies, two prominent bluffs of stained rocks and sulphides, were higher on the face of the ridge and extended from about 530 to 850 feet elevation. North from the bluff tops, the ridge comb rose gradually to about 1,200 feet elevation. The name of the discoverer and the date of discovery of the Hidden Creek orebodies are probably unknown, but the discoverer is believed to have been an Indian from one of the reservations along Observatory inlet. The deposit was brought to the attention of John Flewin, Government Agent at Post Simpson, near the beginning of the present century. Mr. M. K. Rodgers, developer of the Nickel Plate mine at Hedley, did the first organized work on the deposits. Next the Hidden Creek Copper Company prospected the property. Rodgers acquired the prospect a second time, did more work, and finally in 1910 optioned the property to the Granby Consolidated Mining, Smelting and Power Company, Limited, at that time operating at Phoenix and Grand Forks in the Boundary district of British Columbia. The optionees stepped up the development work and brought the property to production in 1914. The ores were direct smelted until 1924. In that year a mill was built. From 1930 until the end of the productive life of the properties in 1935, all of the ore was milled and the concentrate smelted. From March 17, 1914, until July 31, 1935, the production from the Hidden Creek mine was, in round numbers, 18,000,000 tons of 1.70 per cent copper ore and 6,000,000 tons of low grade dilution rock. The Hidden Creek mine ""died with its boots on"". During 1934 the average monthly production was 146,377 tons of 1.06 per cent copper ore. For 7 months of 1935 the average was 161,750 tons of 1.03 per cent ore, and for the final month, July 1935, the production was 156,950 tons."

Jan 1, 1954

By A. G. Pronk, D. M. Burton

"A regional till sampling program in the Upsalquitch Forks-Tetagouche Lakes area, centred some 70km west of the city of Bathurst, has proven an effective method for gold exploration in the heavily glaciated interior of northern New Brunswick. Prospecting activities within this area over the past three years, have led to the discovery of several gold occurences associated with quartz-carbonate alteration in a variety of intrusive rock types emplaced along major fault zonesQuaternary mapping shows that the glacial history is complex. However, the displacement of material is uniform in distance and direction, and the till is generally thin (0.5 m to 2.0 m) and locally derived, making the interpretation of till geochemical patterns relatively simple for the explorationist. Previous studies have shown the the fin e-grained gold is best detected in the -250 mesh (-0.063 mm) till fraction (clay plus silt) and that the C-horizon is the preferred medium for analyses.Samples were collected on a 2 km grid and analyzed f or Cu, Pb, Zn, Au, Ag, As, Sb, Mn, Fe, Ni, Co, and Cd. Results indicate that concentrations of 10 to 20 ppb Au can effectively delineate areas of anomalous gold in bedrock associated with fault structures, and that a good potential for discoveries exists to the west of the known occurrences, where up to 678 ppb A u has been detected in tills. IntroductionThis paper reports on the result s of surficial geological investigations conducted over the past two field seasons in north-central New Brunswick. The stud y area is located in the Upsalquitch Forks-Tetagouche Lakes map area s (N.T.S. 21 0 19 and 21 0 (10) 70 km west of the city of Bathurst (Fig. I). The area is situated on the margin of the New Brunswick Highlands and has a maximum elevation of 640 m (for a detailed description of the physiography, see Rampton et al. 1984).Historically, exploration in northern New Brunswick has concentrated on base metals within the Cambro-Ordovician Tetagouche Group, resulting in the discovery of man y significant massive sulphide deposits (Brunswick No.6 and No. 12, Heath Steele, Caribou, Armstrong Brook, Orvan Brook, McMaster, Murray Brook, and Restigouche). Auriferous base metal occurrences along the Rocky Brook-Millstream Fault have also been previously investigated."

Jan 1, 1988

By Richard W. Hutchinson, Christopher Osterman

The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and footwall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fIne grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfIde piercement structures and the footwall Cu-PGE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch, S. Moon

"Some materials when exposed to various conditions can exhibit a rise in temperature without requiring an external heat source. Generally referred to as pyrophoric or self-heating substances, they challenge the safety of materials handling, storage and transportation. Reliably assessing the self-heating potential of materials is thus essential. Over the years a number of test protocols have been developed. A widely accepted method is that recommended by the United Nations to certify the safety of shipping pyrophoric goods. Our test work on sulphide materials has shown that the U.N. test can give false negatives if the sample oxidation history is not considered. Depending on the degree of oxidation (“weathering”), the same sulphide material can exhibit self-heating ranging from safe to hazardous. For concentrates, oxidation can occur during storage and transport making the sample weathering history an important consideration in the test work. To make the U.N. test, and other single-stage self-heating procedures, more reliable in assessing self-heating potential when testing sulphide materials, it is suggested that a weathering step be incorporated in the test protocol. This test work for two sulphide samples, an ore and a concentrate, demonstrates the impact of incorporating a weathering stage in the test protocol. INTRODUCTIONSelf-heating occurs when exothermic reactions produce heat faster than can be dissipated to the surroundings. Numerous substances self-heat, ranging from wood chips and powdered milk to coal and sulphide minerals (Beever & Crowhurst, 1989; Hudak, 2002). Mixtures of sulphide minerals, most notably those containing the iron sulphide pyrrhotite (Fe(1-x)S), commonly encountered in the extraction of base metals (e.g., copper, zinc, lead, and nickel), are particularly prone to self-heating (Rosenblum, Nesset, & Spira, 2001; Payant, Rosenblum, Nesset, & Finch, 2012). In the mining and subsequent processing stages, the minerals are progressively liberated and finely ground, then separated, usually by flotation, with the resulting concentrates stored and transported to smelters for metal extraction. At most of these stages the sulphides are exposed to both moisture and oxygen, conditions that promote partial sulphide oxidation and the formation of elemental sulphur. Studies have shown that pyrrhotite, in particular, readily oxidizes to form elemental sulphur (Bernier & Li, 2003; Belzile, Chen, Cai, & Li, 2004; Somot & Finch, 2010). The elemental sulphur becomes fuel for further self-heating as the temperature of the mineral mixture increases above 100 oC (Rosenblum & Spira, 1995; Somot & Finch, 2010). It is believed the propensity of pyrrhotite to self-heat is a result of its iron-deficient, and hence somewhat unstable structure. It is worth noting that pure metal sulphides (with the exception of pyrrhotite) do not exhibit appreciable self-heating. A mixture of minerals sufficiently different in their electrochemical rest potential is required to initiate self-heating at ambient temperatures (Payant et al., 2012)."

Jan 1, 2016

By Éric Côté

Introduction The 425 Main Ore Zone ? Block of ore partially mined in the late sixties; ? Area was sealed off for over 30 years due to SO2 emissions from oxidizing fill material; 425 Project goal ? Bring the zone back into production without jeopardizing the mine; ? Minimize risks associated to SO2;

Feb 1, 2008

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By D. M. Hausen

"Refractoriness in Carlin-type gold ores results mostly from fine locking of gold in pyrite, locking in various gangue phases, notably quartz, and a ""preg robbing"" condition attributed to organic carbon. All three conditions may occur in any given deposit, including Newmont &apos;s Carlin and Gold Quarry deposits in Nevada, where types of ref ractoriness occur locally in minor amounts.Measurements of specific gravity, water absorption and screen size distributions of gold in alteration rock types from Gold Quarry show transitional changes from siliceous cherts through decreasingly silicified and increasingly argillized siltstones.Low permeability of siliceous ores contributes to ""size dependent"" refractoriness in cyanidation test work. Colligative physical and chemical measurements demonstrate that silicified cherty ores are difficult to grind, poorly permeable, and less amenable to cyanidation. Refractoriness in pad or column leaching of coarsely crushed siliceous siltstones and cherts is shown to correlate with interrelated measurable mineralogic and physical parameters.IntroductionMetallurgical treatment of variably amenable and refractory types of gold ore may be guided by both analytical and mineralogic data on the interlocking of gold (microscopic an d sub- microscopic) in assorted gangue/sulphide phases. Most oxidized ores from the Carlin gold mine, north of Carlin, Nevada, are amenable to direct cyanidation. The permeability of most oxidized ores from Carlin coupled with the fine size of the gold < 1.5 um) yields rapid extractions and high recovery without fine grinding.Small portions of the Carlin ore body, and also the nearby Maggie Creek and Gold Quarry orebodies, are less amenable to cyanidation, and are classified as refractory. Refractory conditions may be attributed mostly to the association or interlocking of gold with pyrite and /or microcrystalline quartz or chert, and also by the adsorption of leached gold by deleterious forms of carbon, termed ""preg-robbing"" carbon. Each of these conditions are described and defined, with emphasis on a form of silica-locking, which has been referred to as "" size dependent"" refractoriness."

Jan 1, 1985

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By Balmer Neilly

We are regularly told that before making a new investment one should seek the advice of his banker. If we were to place the subject matter of this paper before bankers. other than those who have experience in our mining camps, their reply would probably be evasive. However, if for example: a mining company asks them for a loan and offers as security certain mining investments, they are, in most cases, explosively candid. The idea is preposterous, unless, under Section 88 of the Bank Act, the mining company is able to deposit with the bank, gold or silver bullion, to an amount sufficiently in excess of the loan, to provide for what the banker describes as a reasonable margin of safety in case of contingencies. In addition the directors of the mine personally must jointly and severally guarantee payment of the loan. With any of these conditions missing the banking atmosphere becomes chilly. The local manager explains that the general situation, and particularly European conditions, are so unsettled that head office has warned him that his discretionary powers must not be exceeded under any circumstances.

Jan 1, 1924

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By B. F. Giyani, D. Rahal

"Stirred media mills have proved to be more energy-efficient than the conventional ball milling for fine grinding applications. The mill performance is governed by a number of operating variables including mill stirrer speed, feed particle size, solids content and slurry rheology. A study was conducted to assess effects of mill speed, media size and density, and slurry density on the Stress Intensity (SI) in a VXPmill and thereby the relationship to mill performance. For the mill speeds tested, it was found that the optimum tip speed is 7 m/s. If the speed is too high (12 m/s) energy losses result due to mechanical friction losses and heat generation. If the speed is too low (3 m/s), the kinetic energy is not sufficient to promote breakage. The size reduction ratio increases with the increase in mill speed and the decrease in solids content especially in the coarse fraction particle sizes. The effect of slurry rheology on mill performance was shown by assessing the effects of increasing solids concentration and decreasing particle size. Rheological effects seemed to interact with mill speed such that the mill was less energy-efficient at higher solids content and at higher mill speeds particularly for grinding to fine particle sizes. There is an opti"

Jan 1, 2017