Search Documents

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Valuable base metals, such as nickel, cobalt, molybdenum, vanadium and tungsten, are used in a wide range of important technological applications. The demand for many of these metals has increased significantly over the last few decades, driven especially by economic expansion in Asia generally and China in particular. This has led in turn to a large growth in the output of mines in order to satisfy this increasing demand, as shown by the data in Table 1 (USGS, 1994, 2014). These data reflect an even longer trend of growth of these metals, with nickel, for example, showing an average rate of 5.3% per year from 1980 until 2015 (International Nickel Study Group, 2017). This rapid and sustained rate of growth means that annual mine outputs for nickel, tungsten, molybdenum and vanadium have had to double roughly every 11 to 14 years, whilst cobalt mine output has had to double roughly every 7 years, over the period from 1994 until 2014. With the average working life of a nickel mine being between 17 and 22 years (Statista, 2017), this means that from the time a nickel mine opens until it closes, the industry needs to find the equivalent of another three or four mines of a similar output to satisfy this relentless growth in demand for the metal."

Jan 1, 2017

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

By P. A. Riveros

The literature on the arsenic disposal practices of the metallurgical industry and the long term stability of the disposed arsenic compounds were reviewed from a Canadian perspective. The review was complemented with visits to selected operating metallurgical sites to obtain information on their specific arsenic disposal practices and the behaviour of their impounded residues. The arsenic disposal procedure currently favoured by the industry involves the formation of an insoluble ferric arsenate compound which is allowed to sediment at the bottom of tailings or residue ponds. It has been shown recently that this poorly formed crystalline compound is similar to ?arsenical ferrihydrite? which is ferrihydrite containing strongly adsorbed arsenate anions. Despite concerns about its long term stability on thermodynamic grounds, arsenical ferrihydrite appears to be stable for many years in the proper environment which includes a slightly acidic pH and oxidizing conditions. A high Fe/As ratio and the presence of heavy metals appear to increase the stability of arsenical ferrihydrite. High temperature operations, such as those encountered in the autoclave treatment of refractory gold ores, are conducive to the formation of scorodite, FeAsO42H2O, and/or a series of ferric arseno-hydroxy-sulphate compounds depending on the solution composition. Scorodite has several advantages over arsenical ferrihydrite as a disposal compound including a lower iron demand, a higher density and a greater thermodynamic stability. New procedures have been developed to generate scorodite at ambient pressure. These procedures would offer significant reductions in capital cost because of the elimination of the need for autoclaves. Lime precipitation which was widely used in the past is being abandoned as a result of strong evidence showing that calcium arsenate compounds decompose slowly in contact with atmospheric CO2 to form calcium carbonate and soluble arsenic acid. In all cases, the long term stability of the disposed arsenic compounds depends on a number of factors including disposal site characteristics, particle crystallinity and size distribution, the presence of complexing agents and the effect of bacterial activity.

May 1, 2002

By D. J. Xue

Four kinds of coal-rock combination were subjected to three kinds of stress waves in the SHPB numerical simulation. The wave propagation and the changes of the strain energy in the coal-rock combination during the dynamic impact process were recorded as well as the contact force. The dynamic response law of coal-rock combination was obtained. It was found that the coal had better reflectivity than the rock because of coal with larger impedance. In contrast the rock had better transmissivity. As the crest value of the incident wave increased, the increment in the crest value of the transmitted wave weakened in the coal-coal group, coal-rock group and rock-coal group, in contrast, the increment in the rock-rock group increased.

Aug 1, 2013

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By M. M. C. Lima, L. C. S. Solimani, M. A. Quintela

Galvanized steel scrap is recycled to B OF converters where zinc escapes from the bath and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contain high iron content, it could be recycled, but due to its zinc content, it is disposed in landfills. In this study techniques were evaluated for zinc layer removal from scrap by sulfuric acid leaching. The effects of coating weight, temperature, time and sulfuric acid concentration were evaluated for three different galvanized scrap. The results showed that the behavior of each galvanized scrap was different. Nevertheless zinc removal efficiency was more than 80% with low dissolved iron in the leached solution.

Jan 1, 2011

By Z. Huda

The effect of various percentages of cold-working and recrystallization on the microstructure and hardness of commercially-pure aluminum plate, has been studied. The 'A critical deformation for the aluminum, has been determined. Experimentation involved cold rolling and recrystallization processes followed by quantitative metallographic practice and the hardness measurements. The raw material chosen was a plate of commercial aluminum which was cold rolled to different percentage of cold-work and then recrystallized by heat treatment at 150°C. The critical deformation percentage of aluminum was computed to be around 30% of cold-worked.

Jan 1, 2007

By G. Itoh, S. Fukasawa

The Al-Zn-Mg alloys have been known to be susceptible to stress corrosion cracking (SCC), which is based on intergranular cracking arisen from hydrogen embrittlement (HE). The mechanism of HE has not been fully understood yet. In order to elucidate the mechanism of HE, we need to investigate the behavior of hydrogen in the alloys. In this paper, behavior of hydrogen in an Al-5.8%Zn-2.4Mg alloy was investigated by means of hydrogen microprint technique, a method to visualize location of hydrogen emission from specimen surface as silver particles. One side of the tensile test pieces was electrolytically polished and then covered with photographic emulsion. Hydrogen was pre-introduced into the test pieces from opposite side by cathodic electrolytic charging for 30min. Then, the test pieces were stretched with continuing the charging. After that, the specimen was fixed, rinsed, dried and observed with a scanning electron microscope. As a result, silver particles were observed on some grain boundaries.

Jan 1, 2015

By A. G. Eccles

Western Mines' milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine's location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines' alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By Paul Toor

The operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles ? in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By Tugba Cebeci, Bahjat Khoshaba, Bern Klein, Libin Tong, Andrew Bamber

"Sensor-based sorting technologies have potential to pre-concentrate low grade subeconomic ores through discarding the barren waste particles. However, the inability of sensors to accurately discriminate ore from waste is a barrier to prevent their wide applications. The present study focuses on the development of more intelligent sensing systems by using correlation and regression analysis of X-ray fluorescence (XRF) sensor responses on the copper ore samples obtained from Chile. The responses obtained through XRF scanning were reported both in the form of counts and the grades of elements. Linear and multiple linear correlation analyses were made between the XRF counts and the copper grades obtained through chemical analysis. Both the heterogeneity of the ore particles and the matrix effect in the XRF measurement are discussed in the study.INTRODUCTIONSorting can not only discard waste rocks away from the concentrator but also recover metal bearing ore particles that would be lost to the waste dump. The benefits of ore sorting include reduced energy consumption, water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). X-ray fluorescence belongs to sensor-based sorting technologies and Xrays are a high energy-high frequency form of electromagnetic radiation inhabiting the region between the ultraviolet radiation and gamma rays (Shackley, 2011). Recent XRF sorting studies on low grade copper ores were carried out at MineSense Technologies Ltd. aimed at increasing the capacity related to improving the understanding of ore heterogeneity as the basis for developing semi-bulk or bulk sorting systems (MineSense Technologies Ltd., 2016)."

Jan 1, 2016