Search Documents

By A. F. Banks

"IntroductionThe typical potash processing plant recovers and/ or upgrades from 10% to 20% of its production through the recrystallization process. The feed to the recrystallization section consists of preconcentrated slurries of fine crystal size that cannot be raised to the required product grade by flotation and fine dusts also of low grade and too fine for compaction feed. It produces high grade white potash crystals that can be marketed as a high grade product or blended into the flotation products to raise their grade. In this chapter, a typical leaching (dissolving) and recrystallization operation will be discussed.The crystallization process makes use of the three phase system chemistry of NaCl, KCl, and H,O. The normal potash process operates on a temperature range of 75°F to 95 °F. A three phase slurry feed to the dissolving circuits will be within that range. The potash (KCl) is dissolved by heating the slurry in the presence of sufficient brine to a temperature of 190°F to 200°F. As the slurry is heated, the potash (KCI) dissolves and the salt (NaCI) precipitates. The potash rich brine is then clarified and the salt and other undissolved solids removed by thickening. Clarified brine becomes the crystallizer feed.The hot brine is cooled in evaporative cooling crystallizers. In cooling, the potash precipitates as a high grade white crystal. Crystallization is done in multiple effects to permit energy recovery and control of the process. In a four effect crystallizer the cooling is done by recycling mother liquor counter currently through the first two effect condensors and using brine pond brine for the cooling of the last two.The crystallizer product is removed from the last effect as a slurry at normal process temperature and is fed either to its own centrifuging and drying circuit or blended with the flotation product for centrifuging and drying."

Jan 1, 1989

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By T. Schepp, T. Friedrich

"The natural stage of deep mines operation is a closure of unnecessary shafts. It is extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. The paper presents a short overview of shaft closure methods and available tools and devices developed in the last time for such shaft inspections. INTRODUCTION The natural stage of deep mines operation, commonly occurring after depletion of the reserves of mined materials, is a closure of unnecessary shafts. All over the world, the number of liquidated shafts grows continuously and the problem of shafts disposal is especially critical for deep shafts. The typical depth of 600 m of currently liquidated shafts in Poland may already be seen as a challenging task. The greater is the challenge of shaft closure in Germany where the last active coal mines for shafts with a depth of up to 1,300 m have been recently closed. It is therefore extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. In many cases, it is more important to inspect old, abandoned shafts, where the wall stability or even liner type are not fully known. SHAFT CLOSURE METHODS Abandoning a shaft is a complicated task, as shafts, being the link between the surface and an underground network of workings, disturb hydrogeological and gaseous conditions in the rock mass (Sztelak, 1991). Closure procedures at older mine sites have been carried out in accordance with earlier legislative requirements. For very old shafts (+100 years), it means in many cases only a sealing of the shaft entrances by means of timber or concrete slabs. In the 20th century, the shafts were also closed by means of filling with grainy materials, but even then the retrospective activities at abandoned mine sites were extremely limited and in most cases no further monitoring measures were performed. The possible consequence of an improper shaft closure and lack of monitoring is presented in Figure 1."

Jan 1, 2019

By C. Sideco

"Concentrate drying at the Sullivan Concentrator goes back to 1937 when the original coal-fired dryer was put into operation. This was a second hand 8' dia. x 56' long Struthers-Wells rotary dryer that came from the phosphate plant in Warfield, B.C.In 1962, replacement of the old dryer was seriously considered. The shell and the auxiliary drive mechanism were badly worn and needed replacing. In April 1963, the new 8' dia. x 65' long fuel oil-fired Struthers-Wells dryer went in operation at an installed cost of $174,000.In 1965, it was apparent that a major rebuilding of the dust collecting system would have to be done. A study was carried out and a Ducon Dynamic Gas Scrubber was installed. The system went in operation in November 1966 and has fully met expectations.In the same year, the zinc dryer was converted from fuel oil to natural gas. The conversion has resulted in savings in fuel cost of 12 to 15%.Frame No. 1Zinc Dryer PerformanceDryer Make - Struthers-WellsDryer Size 3/4 8' dia. x 65' long Drum Drive - 100 HPSpeed of Rotation - 5 RPMFeed Rate - 50-65 TPHFeed Moisture - 10-12%Discharge Moisture - 4-6%Dryer Inlet Temperature - 1600-1800°F Dryer Outlet Temperature - 200-250°F Stack Gas Volume - 25,000-40,000 CFNDust Collecting Efficiency - 99.75-99.98% Duet Loss in Stack - 50-300 lbs./day"

Jan 1, 1972

By Blaycock. S. C.

WE should indeed feel proud and satisfied with the accomplishments of our great mining and metallurgical. industries during the past quarter of a century, for they have vastly exceeded those of any previous period of like duration. 1 feel that Canadians, and particularly those in the mining industry, should know more concerning the important role our industry will be called upon to play in the present war. Our Empire metals will be an outstanding factor in this conflict. Every man connected with the industry, from the lowest paid labourer to the highest official, can feel proud that his every effort results in more and more production of those metals which will help to give the Empire supremacy. He can feel assured that, by sticking to his job and by putting his whole heart into his work, he is making a contribution towards winning the terrible struggle in which our Empire and our gallant French allies are engaged. These two great peoples will have ro bear the brunt of the task of ridding the world of the menace of those who would set up force. and might in the place of right and justice in the settlement of international affairs. As the present European crisis developed, it became evident that they, alone, would have to accept the challenge and fight the enemies of Democracy to ensure the survival of the small nations of Europe and, indeed, of the great democratic powers themselves. The acquisitive eye of the German leaders had looked far ahead and they had realized that the eastern European states, already reeming with population, were no solution to Germany's space problem; but they thought that these states could be gobbled up one by one, each in turn strengthening Germany's might until it could successfully challenge France and England. No glimmer of doubt dimmed their vision. The two great democracies once subdued, they could proceed to seize Canada and the United States. This clone, they would have an abundance of room to expand, as well as those resources-grain, timber, cotton, nickel, iron, lead, zinc, copper, gold, silver, sulphur, oil-which German statesmen have always coveted. Von Ribbentrop, von Alvensleben, Bernstorff, and many others have made exhaustive studies of our resources. German rulers had been told that the French would not fight and that the British could not. They knew of the rust on the British war machine. There was no cloud in the sky; their fond dream was at last robe fulfilled.

Jan 1, 1940

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972

By Ed McConaghy, P. LaRochelle

The Ambatovy Nickel Project comprises the development of mine, hydrometallurgical processing facilities and necessary infrastructure in Madagascar, positioning Ambatovy as one of the world’s largest producers of nickel and cobalt from lateritic ore. SNC-Lavalin successfully provided comprehensive Engineering, Procurement, Construction Management (EPCM) services for this major capital project which, apart from its sheer size, scope, and engineering design, represented significant location, infrastructure, labour, environmental and climatic challenges. Today, the project has reached 90% of its nameplate capacity and is in its final performance optimization stage. This paper will discuss the significant project management effort that was required to successfully address the complexity of this major project. It will cover the main project management control systems and the engineering tools and processes used during the detail engineering, procurement, and construction phases to achieve optimum project execution.

Jan 1, 2015

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By Edward R. Rose

This paper summarizes and emphasizes the potential importance of Canadian rare-earth occurrences, and recommends that efforts to locate and evaluate rare-earth deposits should be increased. Increasing world markets, depending on intensive applied research into the numerous unique and remarkable chemical and physical properties of the rare-earth elements (REE), are developing; their properties and uses are becoming better known; methods of separation are much improved. The REE group comprises a Cerium (Light) subgroup of 7 metals and an Yttrium (Heavy) subgroup of 9 metals. REE are trace elements in many rocks and minerals, and major constituents of more than 50 rare-earth minerals, many of which are difficult to detect and identify. They occur preferentially in acidic and alkaline igneous and metamorphic rocks, including carbonatites, as well as in placer deposits, certain uranium deposits, phosphate rocks and others. The main ores now are bastnaesite (in Precambrian carbonatite), monazite and xenotime (in Recent beach sands) as well as uraninite and brannerite (in Huronian quartz-pebble conglomerate) and loperite (perovskite) and apatite (in alkaline complexes). World resources are summarized. Twenty mines in 1973 produced an estimated world total of about 31,000 tons of contained rare-earth oxides (REO), 19,341 tons of which came from one mine at Mountain Pass, California. A selected fifteen, of 315 or more Canadian occurrences, are briefly described and compared, and their relative merits indicated. Their abundance and variety suggest the possibility of finding high-grade deposits in many geological terranes in Canada.

Jan 1, 1979

By Harold Hopkins

THE Wright-Hargreaves mine is one of a group of seven mines long active in the Kirkland Lake district, Ontario. Detailed geological reports and maps covering the area have been published by the Ontario Department of Mines (1,3)t. Though all these mines work several productive veins there is one vein which is common to all and is known as the North Vein of the camp?not that it is the most northerly vein mined, but it is the more northerly of the two major veins of the camp. At the Wright-Hargreaves mine there are in all ten important producing veins, and most of them have a N.60°-65°E. strike and in general a steep southerly dip. It is a common belief that most of these veins lie along faults but it will be shown that whilst this is true of some of them it is not true of all, and also that a vein may lie in a fault along part of its course and elsewhere fill a fracture in line with the fault, this being a consequence of rotational movements that took place during faulting. The paper describes the history of faulting at this mine in particular, makes observations on the principal pre-ore fault, and describes the method used in solving the movements on the post-ore faults. Other details of geology are not discussed except to mention here that our main veins lie almost entirely in the syenite porphyry stock except on lower levels close to the east boundary of the property, where the North vein leaves the porphyry to enter the greywacke.

Jan 1, 1940

By L. Xia, B. Hart, G. Gingras, M. Furlotte

Plant and laboratory test work was performed in order to optimize a copper/zinc flotation separation circuit at Matagami concentrator, Canada. The testing identified a significant difference between the laboratory testing and the plant flotation, particularly for the sphalerite recovery in the rougher copper concentrate. Tests indicate that sphalerite recovery of the flotation concentrate in the laboratory testing was significantly higher than in the plant. The ToF-SIMS surface analysis identifies surface species responsible for the discrepancy in Zn recovery. It shows that sphalerite flotation is in response to the collector attachment and a significant enrichment of Cu on the surface of sphalerite grains. A comparative surface chemical analysis was performed on both sphalerite and chalcopyrite grains from the plant flotation and laboratory testing in order to identify surface species variability between the two testing. Two significant observations were revealed. First, there is considerably more hydrophilic iron oxyhydroxide on sphalerite surface from the plant flotation sample relative to those from the lab testing. The secondary coating likely completely or partially passivates sphalerite surfaces, reducing Cu enrichment and hence sphalerite floatability. Secondly, comparing the surface chemistry on sphalerite and chalcopyrite, the hydrophilic iron oxyhydroxide species have preference for the sphalerite grains relative to chalcopyrite. Despite numerous studies on the effect of galvanic coupling during grinding, there is limited documented evidence on the effect of the milling environment on the flotation and plant operations. This observation suggests that interaction between sulphide minerals and grinding media have a significant influence on subsequent flotation. This paper discusses the results of a detailed surface chemical evaluation of sphalerite grains from both the plant and laboratory testing in the context of grinding environments and pulp chemistry.

Jan 1, 2016

By G. Deschênes

Located in North West Tanzania, Buzwagi is an underground narrow-vein gold mine owned by Barrick Gold. The plant was commissioned in 2000. The reserves are estimated to be more than 25 years. The ore, containing gold, silver and copper mineralization in sulphides, is processed at 3,300 tpd. This paper presents the results of an investigation to determine the performance of an ammonia-cyanide leaching approach to recover gold from two samples. Coarse gold was recovered by gravity prior to leaching. The gravity tailings had the following composition; 1.97 g/t Au and 0.31% copper for the medium cyanide soluble copper (MCSC) sample and 2.80 g/t Au and 0.53% Cu for the high cyanide soluble copper (HCSC) sample. Experiments were conducted for 72 hours in stirred tank reactors with monitoring and control of parameters. The straight cyanidation produced gold extractions of 76.1% for the MCSC sample and 84.6% for the HCSC sample. Associated cyanide additions were 6.1 kg/t and 11.5 kg/t respectively. The gold extraction of the MCSC sample was improved to 88.8% using 350 ppm NaCN and 700 ppm ammonia. The associated cyanide and ammonia additions were 2.5 kg/t and 1.7 kg/t respectively. For the HCSC sample, 82.5% gold extraction was obtained using 500 ppm NaCN and 600 ppm ammonia. The cyanide addition and ammonia additions were reduced to 3.8 kg/t and 1.0 kg/t respectively. No significant decrease in gold extraction was noticed when the cyanide and ammonia were reduced to 150 ppm and 500 ppm respectively. In the presence of ammonia, a significant amount of cyanide was oxidized to cyanate by the cupric ion. In the absence of ammonia, the formation of copper cyanide was the predominant reaction responsible for consumption of cyanide.

Jan 1, 2012

By Thomas Mütze, Frank van der Meer, Gunnar Kretschmar

"The air classification of moist bulk materials is addressed in the literature insufficiently. Therefore a feasibility study investigated the influence of feed moisture on the separation efficiency expecting a reduction with higher moisture content in the feed. Two iron ore samples were characterized in terms of the nature of bonding of moisture as well as its effect on the agglomerate strength. The classification tests themselves were conducted with two dynamic laboratory air classifiers at cut sizes from 45 to 110 µm and a moisture of the feed material between 0 to 10 wt.-%. The quality of classification was assessed by split factor, cut size, separation efficiency, moisture of both products, as well as the yield of the fines as product fraction in a corresponding processing plant. An initial approach was found for a technological implementation: A sufficient drying of a moist feed can be realized simultaneously to the pneumatic transport inside the classifiers. In the present case the drying effect and dispersion intensity was sufficient to provide good separation results up to 3 wt.-% feed moisture. An additional drying step was necessary beyond 3 wt.-%.INTRODUCTIONSpecific information about the influence of moisture in air classifiers is very rare. Mostly only dry products are processed and/or drying prior to classification is recommended. Apart from the specific influence of the feed moisture a lot of literature can be found regarding air classification itself. Altogether air classification can be divided into several sub-process (Leschonski, 1977):- dosage of the feed material,- dispersing the solid feed material into a gas stream,- feeding the dispersed material into the classification zone by pneumatic conveying,- separation of coarse and fine particles, and- separation of fine particles from gas.For wet feed particles also drying plays an important role. Interesting for the present investigation are the humidity of the feed and its influence on the single sub-processes."

Jan 1, 2016

By Oliver Hall

WITH the friendly consent both of the Institution of Mining and Metallurgy, for whom this paper was written, and of the author, we had the pleasure of publishing Mr. Oliver Hall's paper on Mining at Noranda in our issue of last March and of having Mr. Hall present it at the Montreal Meeting. In the following pages we now report the discussion elicited by the paper at a meeting of the Institution in London on March 18th. The report is taken from the April, 1937, issue of the Bulletin of the Institution, to whom we again tender our thanks. THE PRESIDENT (MR. ROBERT ANNAN) said that this paper was, by arrangement with the Institution and the author, also being published by the Canadian Institute of Mining and Metallurgy for approximately simultaneous discussion. He was sorry that Mr. Oliver Hall could not be present to introduce it in person, for he was sure that the author would have had many more details to give about this most interesting mine. The paper contained a very useful account of mining operations, and personally he had been pleased to see the tri-dimensional projections of the orebody in Figs. 3 and S. It was a good illustration o the value of that method in presenting the form of an orebody such as this. While he had no desire to go into technical details, he wished to call attention to a remark in Mr. Hall's introduction, in dealing with the history of the mine and the principles on which it was run. The author had given an account of the early difficulties in solving geological problems, and later of the economic difficulties of seeing this mine through a period of intense depression in metal prices. He stated that it was clear that, to maintain income, tonnage must be increased, and, to maintain profits, costs must be decreased. It would be observed that there was no question of increasing the grade of ore. Then the author went on to say: 'Having set the house in order in the years of adversity, the higher price for gold is being used to mine to still lower limits and lengthen the life of the enterprise and the welfare of those dependent on it'.

Jan 1, 1937

By G. Minhas, M. Pule, Y. Laffitte, M. c. McGurn, T. Tzanetakis, Peacey. J., R. Susilo

Titanium (Ti) metal production from titanium tetrachloride (TiCl4) using magnesium (Mg) as a reducing agent is the well-known Kroll process. A chloride route is used to avoid oxidation of the titanium sponge. The sponge is consolidated into ingots and can then be made into powder by melting and atomizing or by hydriding/dehydriding. Attempts at direct powder production have met with difficulties, including low Ti yield and the formation of very fine particles (particles between 25-100 µm are desired). This paper discusses two methods to produce Ti powder in a molten salt medium using magnesium powder as a starting material instead of a pool of molten magnesium. The first method is a direct reduction of gaseous TiCl4 injected in the melt with the magnesium powder in suspension in the molten salt. The second method is a two stage TiCl4 reduction reaction where recycled Ti was used to form titanium dichloride (TiCl2) in the first stage followed by addition of magnesium powder into molten salt in the second stage. A correlation between Ti yield and processing variables such as TiCl4 to Mg ratio, Mg particle size, TiCl2 concentration in the melt, and reaction temperature was studied. The Ti powder formed was also analyzed for particle size distribution. Despite challenges and difficulties encountered, this paper shows some promising results which could provide guidance to others working on direct Ti powder production.

Jan 1, 2015

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By Edward I. Renouard

"THE mineral industry is constantly undergoing changes and facing challenges, and today we are in the midst of another serious one -namely, manpower requirement at every level in the mines, shops and plants. In the not too distant past we had a situation where labour was plentiful, although the equipment, by present-day standards, was quite inadequate, and that's easily understandable when you look back at the primitive methods by which our Western mines were first developed and operated, and then improved by the inventiveness and ingenuity of man.I'd like to show you a few slides from drawings made by Buck O'-Donnell which illustrate some of yesterday's methods of mining. Some of you probably had first-hand experience with some of these so you know they were tedious, time-consuming and involved a lot of heavy labour.Taking the Anaconda Company operations at Butte as an example, we can see what has happened in just the past ten years. In August of 1956, the Butte mines had 5,516 day's-pay employees and 976 salaried employees, for a total payroll of 6,492. In August of this year, there were 3,645 day's-pay employees and 605 on the salaried roll, for a total of 4,250. The number of contract miners had gone from 1,347 in 1956 to 606 in 1966 and that of other underground miners from 2,893 ten years ago to 1,149 this year. Along with these changes, however, another change of special significance has taken place, and that is in the number of skilled craftsmen, surface engineers and so on required for our operations. In 1966, we had 1,890 of these people, 600 more than in 1956 and nearly three times as many as just twenty years ago."

Jan 1, 1967