Search Documents

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By Philippe Portella

Current Ownership : AREVA NC-France & affiliates (63.4%), ONAREM-Niger (36.6%)Related Mines : Ariège, Artois, Arlette(initial Somaïrlease) and Tamou, Taza, Takriza, Tamgak(SMTT lease)Mining Method : Open Pits Reserves : about 14 000 tU Average grade : 0.3 % UEnvironmental Management : Certified ISO 14001 since November 2002Key figures :2003 output : 1126 tU number of employees at year end : 565 Current Ownership : AREVA NC-France & affiliates (34%), ONAREM-Niger (31%), OURD-Japan (25%), ENUSA-Spain (10%) Related Mines : the Akouta mine provides access to several adjacent orebodies(Akola, Akouta, and coming Afasto with Ebba North / South)Mining Method : Underground ?mainly room & pillars Reserves : about 29 000 tU Average grade : 0.40 to 0.50 % U3O8Environmental Management : Certified ISO 14001 since January 2003Key figures :2003 output : 2017 tU number of employees at year end: 1070

May 1, 2006

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By M. Reda

Erosion corrosion is acceleration in the rate of corrosion attack in metal due to the relative motion of a corrosive fluid and a metal surface [1]. The increased turbulence caused by pitting on the internal surfaces of a tube can result in rapidly increasing erosion rates and eventually a leak [2]. Engineers and scientists in different disciplines have worked for many years on methods of complete protection from flow induced corrosion or partially reducing corrosion of this type, and they have proposed or applied different countermeasures [2]. The accident at the Surry-2 nuclear power plant (USA) and other similar incidents have once again disturbed the scientific-technical community. This has forced the plant operating personnel and the management to undertake wide-ranging measures in order to discover on time, assess, and monitor such cases. In these extreme cases, protective coating and even metallic bulk material coating (the substrate itself) may suffer considerably from mechanically induced damage [2]. At high velocities, the "leaching out" dissolution reaction of particular, for example, steel elements at the solid-liquid interface become the rate determining step. One practical example for the difference between erosion corrosion and flow induced corrosion is the famous steam eruption from a Japanese [3, 4] nuclear power plant cooling system at the pressurized water reactor (PWR), turbine and in the condenser-steam generator connecting pipe. The rupture occurred in the carbon steel pipe connecting the condenser and steam generator. The damage occurred in the easily eroded/corroded carbon steel at a vulnerable location downstream of an orifice plate, In general, when there is significant reduction in pipe thickness through erosion/corrosion, distinctive patterns are visible, but those patterns were not observed in this case, Thus one can speculate that another phenomenon is possibly controlling, Fluid flow within pipes reduces the pipe thickness leading to an eventual rupture, The thickness reduction mechanism is erosion/corrosion, One example is "cavitations corrosion", Erosion and corrosion occur at the same time, and it is difficult to determine which one is dominant, Therefore, the term, "erosion/corrosion," is used [5]. In the atomic energy field, the terms "Flow Accelerated Corrosion" and "Flow Induced Corrosion" are also used. It is the purpose here to show that during flow induced corrosion a different mechanism may possibly be operating and in some cases it can be different from the well known erosion corrosion. Another example is fretting failures in early Canadian nuclear steam generators which was thought to be due to excessive vibration caused by high.

Jan 1, 2010

By P. Bakke

Following extensive R&D efforts, Hydro Magnesium has launched a new alloy series with remarkable combinations of properties. The AE alloy family is based on additions of aluminium and rare earth elements to control mechanical properties, including elevated temperature creep strength. By combining these alloying elements with manganese additions, high purity alloys with outstanding corrosion performance are defined. A basic philosophy behind the developments has been to simultaneously approach all the critical issues related to developing a commercial material. Apart from the obvious requirements for material properties, the critical issues relate to die casting performance, as well as alloy production, recycling and environmental compatibility. Some of the important elements related to alloy production and recycling are addressed in the present paper.

Jan 1, 2006

By K. G. Chipman

THE discussion on Dr. Chipman's paper, Mapping by the Topographical Survey, centred mainly on the urgent need for aerial photographic reconnaissance of unmapped portions of the country as an initial phase in the provision of suitable topographical maps for use as a guide in geological mapping, prospecting, exploration, and development work in the areas concerned. This, ir was pointed out, would necessitate an expansion of the topographical work of the Bureau of Topography to keep pace with the photographid work and to meet the demand for maps for use by geologists of the Bureau of Geology and others. A resolution requesting Institute Council to make representations to the proper authorities, urging that aerial photography and topographic map-ping be greatly expanded to meet the pressing needs of the situation, was moved by DR. W. F. JAMES and seconded by MR. L. G. SMITH, and carried unanimously. The full text of the resolution appeared on page 221 of the May BULLETIN. Others who spoke in support of the resolution were MESSRS. E. S. MOORE, L. B. ROCHESTER, F. D. SHEPHERD, and W. J. WRIGHT. Dr. Hansen then presented his paper, Mapping by the Geological Survey, discussion on which is summarized below. MR. FRANK EBBUTT(l) spoke of the very valuable service the Geological Survey bas rendered the mineral industry, and indeed the whole nation, in its century of existence, despite the very inadequate financial support it has received. Now, more than ever before, a strong and expanded Geological Survey is essential if the Industry is to continue to prosper. Our known ore reserves are being depleted very rapidly, and we are finding no new orebodies to take their place. As an aid in prospecting and exploration, and also in the development of orebodies when they have been found, we must have geological maps of the vast sections of the country which at present are unmapped or inadequately mapped. The Institute should make every endeavour to have the Geological Survey strengthened so that such maps may be made available as soon as possible.

Jan 1, 1944

By J. C. Ingram

IT SEEMS particularly appropriate that, in celebrating its Diamond Anniversary, the Canadian Institute of Mining and Metalturgy chose our Province of British Columbia as its locale in this, our own Centennial year. I am sure your organization is justifiably proud of its achievements and growth over the period of its sixty years, and we, for our part, are justifiably proud of our growth over our first one hundred years. With your kind indulgence I pro-pose to talk to you today about our industrial growth, or, to put it an-other way, to highlight, historically, our progress in industrial development over the past one hundred years, and to take the liberty of speculating on what we may reasonably look forward to over the next few years. I am sure, Mr. Chairman, that some may have questioned the appropriateness of a talk on the industrial development of British Columbia to the Canadian Institute of Mining and Metallurgy. However, strangely enough, we in British Columbia owe our origin, constitution-ally and industrially, to the mining industry.

Jan 1, 1958

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By Kazuhide Nakaniwa

In this research, we devised a measurement method using total stations (TSs) which have ?the Baum? which is a concentric circle reticle, as substitute for crosshairs. The Baum owes its name to the similarity between the concentric circles and trees (Baum in German). By setting one circle on both of edges of cylinders, operators can set their sights on points on the center line of the cylinders, and also can measure positional coordinates of the points. Also, by measuring two different points on the center line, operators can measure the position and tilt of the axes of the cylinders. Furthermore, we developed a pile driving navigation system. Foundation piles are used for various structures, and their forms are generally cylindrical. Especially, although it is difficult to drive tilted pile foundations, their usage are expected to expand due to their high earthquake resistance. Yet, a method to accurately measure the tilts of piles has not been established. However, we proved that operators can obtain adequate accuracy to control foundation piles through the measurement experiment using this system. Using this system, the information of the pile is measured using a TS, transferred to a PDA, and displayed from the operator?s view of the piling machine.

Aug 1, 2013

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By W. G. Jewitt

THE Box mine, situated in Saskatchewan on the north shore of lake Athabasca, is unique in two respects. It is the first and, so far, the only gold mine in Saskatchewan, and it is the only gold mine in Canada to employ a large-scale forced caving system as the main mining method. Discovered in 1934 by Tom Box, an Edmonton prospector, its subsequent history, while breaking no records for speed, has been one of steady and more or less normal development. Camp and plant are situated close to the shore of Beaverlodge bay, sorne 50 miles east of the Saskatchewan-Alberta boundary and 35 miles south of the north boundary of the Province. The railhead at Waterways, Alberta, is about 220 miles to the southwest. Prince Albert lies some 450 miles to the south. The surrounding country presents a rather rugged variation of the usual Precambrian topography, with hills rising five to six hundred feet above lake Athabasca. The numerous lakes and islands, together with the wide expanse of lake Athabasca, compose an attractive scene, at least in the not over-long 'open water' season. The winters are long but not extremely cold, judged by prairie standards. The small lakes break-up around May 20th and the 'freeze-up' stops navigation early in October. Though apparently remote, the Box mine is fortunate in having reason-ably cheap transportation from Edmonton. The 300-mile railway from Edmonton to Waterways is the most expensive section, the rate for 1st class freight being $1.70 per hundred pounds and for 5th class freight $0.77 per hundred. Freight from Waterways to the mine, approximately 140 miles down the Athabasca river and 90 miles along lake Athabasca, is delivered by barges and tugs for 50 cents per hundred pounds. All freight is delivered during the 'open water' shipping season, which lasts from about .Tune 7th to October 7th. In normal years, barges are loaded to 3 to 3 1/2feet draught up to September 1st. After that date, and earlier in dry years, shallow water at Waterways reduces the barge loads. Barges of 100 to 200 tons capacity handle all mining freight, including pieces up to 15 tons in weight, without undue difficulty.

Jan 1, 1940

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

By M. G. Lipsett

"Mining properties are becoming increasingly remote, a challenging situation for operating and maintaining equipment. Logistics of transporting workers and materials can be alleviated by having timely, accurate information of equipment location and operating condition, and by automating some activities. This paper discusses an infrastructure for remote operations, with strategies for communicating different types of data, and a design method so that systems can interact with either an operator or another system. A remotely operated excavator prototype is described, with on-board performance and diagnostic monitoring systems now used on production equipment. IntroductionSyncrude Canada Ltd. operates an openpit oil sands mine near Fort McMurray, Alberta. For twenty years, draglines and bucketwheel reclaimers have fed conveyors that transport dry oil sand to an extraction and upgrading plant. In converting to a truck and shovel operation, Syncrude has developed slurry pipelines and bitumen froth pumping to allow more remote leases to be mined more than 30 km from the base plant.There are organizational and resourcing challenges in operating and maintaining equipment in three nearby, but separate, mines. The logistics of transporting workers and materials to production and support equipment become more difficult, and operations and maintenance personnel and facilities become more distributed. Supervising mine operations will rely even more on having timely, accurate information about equipment location and operational status.Syncrude is typical of an open-pit operation. Voice communications are the preferred way to exchange information for making immediate decisions about operations and maintenance. A large number of narrowband FM broadcast radio channels keep teams of miners working together. Haul truck drivers, shovel operators, and dispatchers talk on one channel while maintainers coordinate activities with the control tower on another. Cellular phones have become popular for supervisors who have to talk with planners and engineers in offices without radios."

Jan 1, 2000

By J. Stiksma, J. Dennett, R. Kalanchey, J. Ji, M. Collins, T. Chan, R. Berezowsky

A pilot plant campaign has been conducted by Sherritt Technologies in support of Eldorado Gold Corporation’s evaluation of pressure oxidation technology for the treatment of refractory gold concentrates from the Certej deposit in Romania. Four separate concentrates, containing 3.5 to 5.4 g/t Au, 13.0 to 14.5% S2- and 12.0 to 32.5 g/t Ag, were tested in the eight-day campaign. The major gold-bearing mineral was pyrite. Preliminary batch tests indicated that gold extraction from the oxidized concentrates in subsequent cyanide leaching was adversely affected by the presence of organic carbon in the pressure oxidation feed when chloride in solution was at an elevated level. As such, the process conditions that were tested during the pilot plant operation were selected to either counteract the negative impact of the organic carbon, or to deactivate it during pressure oxidation. Both process routes proved feasible, yielding gold extraction of 95 to 98% in cyanide leaching of the oxidized concentrates. Silver extraction was typically in the range of 80 to 90%, provided that the oxidized concentrates were also processed in a lime boil step prior to cyanide leaching.

Jan 1, 2014

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943