Search Documents

By Smortchevskyk N. J.

THIS paper describes the electrical features of the locomotive now (August, 1962) under construction for Craigmont Mines. Intended for non-specialists, it avoids details of design and calculations interesting to electricians only. The paper is divided into three sections. The first deals very briefly with the mine layout and with operating conditions -existing and expected. Reference is made to economic considerations leading to the selection of the type and size of locomotive, as well as to traction diagrams and the calculations. This material is not included in the paper because of its length and because it does not represent anything new. The second section deals with engineering and economic considerations and shows, in some detail, why the A.C. system was chosen. The third section describes the basic components of the locomotive, including the voltage regulator, the rectifiers, the control arrangement and the filter, and deals with considerations affecting the selection of their rating and design. A concluding sub-section describes, very briefly, the track and trolley details and the power distribution switchgear.

Jan 1, 1963

By Ernest Davis

WATER power, until developed, produces nothing, but when harnessed it continues to produce, it might be said, indefinitely. Hence the importance of developing all feasible water powers. British Columbia, like the western states of America, is subject to variable meteorological conditions which cause most streams to be erratic in their flow. The wet season, usually commencing in October and continuing to March or April, together with the melting of the snows during the early summer, produces a heavy run-off which diminishes considerably during the later s1.1,mmer months, with the result that storage is essential on practically every stream in order to regulate the flow to obtain a discharge which will meet the requirements of the load of the markets the power is to serve. Storage sites of sufficient capacity to equate the flows are not always present and it follows that, where such a deficiency exists, the difference must usually be met by burning fuel in steam plants. Fortunately, there are within the Province deposits of high-grade coal, suitable for the operation of such auxiliary steam plants. One of the strongest reasons for the development of water powers is the conservation of fuel. All use of coal or oil depletes resources that can never be renewed. Every water power developed means a saving in fuel and, even if at first it does not possess an over-powering financial advantage, it must become of ever increasing value as fuel resources become depleted. However, sight must not be lost of the inter-relation which should exist between the two methods of generating electrical energy, as each makes an admirable supplement to the? other with respect to suitability for carrying different types of load. In general, it can be said that the fixed charges of a water power development are usually high in relation to the operation costs, while those of fuel power plants are usually the reverse, so it is sometimes possible to combine the two methods of generation for the more efficient production of energy.

Jan 1, 1942

By D. Berkley

The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity. This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remote located industrial facility. It is addressed to the ?users? of cogeneration facilities rather than to ?generators.? The focus is on analyzing various site-specific design considerations to pre-screen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project. Part 1 of this paper (Berkley, 2003) provides a basic understanding of cogeneration plants of various types to establish a common language. Part 2 outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants.

Mar 1, 2003

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By H. O. Seigel

Induced Polarization includes many types of dipolar charge distributions set up by the passage of current through consolidated or unconsolidated rocks. Among its causes are concentration polarization and electrokinetic effects in all rocks and the phenomenon of Overvoltage in rocks containing electronic conductors such as metallic sulphides and graphite. In normal rocks the polarization effects may be usually con-fined within relatively narrow limits and any large departures may be at-tributable to the presence of electronic conductors. In practice, Induced Polarization is measured in one of two ways. In the first a steady current of some seconds duration is passed and abruptly interrupted and the slowly decaying transient voltages existing in the ~round are measured after interruption. This is known as the "pulse", "transient", or Direct Cur-rent Induced Polarization (D.C.I.P.).The second method entails a comparison of apparent resistivities using sinusoidal alternating current of two or more frequencies, generally within the range of 1/10 to 10 c.p.s. Induced Polarization extends the

Jan 1, 1962

By K. U. Kainer

Magnesium and its alloys as the lightest available construction metal offer a wide range of opportunities for the usage in transportation industries, especially Magnesium wrought alloys with their improved mechanical properties show a high potential for structural applications, While magnesium cast components have found their application the interest is now spreading to wrought alloys due to the possibility to get even more homogeneous and better properties compared to cast parts, Therefore alloy and process development especially for extruded and sheet material is a main concern to enhance the application of Magnesium wrought alloys, Castings are still form the majority of applications of magnesium alloys, although efforts to develop adequate wrought alloys have increased, In the presentation, the alloy requirements for processing of cast and wrought alloys will be discussed, The various processing routes and alloy compositions result in specific microstructures and properties which determine the potential use of these alloys, Today, the spectrum of available alloys covers standard alloys as well as alloys for use at elevated temperatures, The trend will be to further diversify the alloy compositions and to improve the alloy properties, Areas of concern still remain the wrought processing and the high temperature (creep) and corrosion properties of magnesium alloys, Examples of recent developments in these sectors will be given, The presentation will also provide an overview of the historical and current use of magnesium and an outlook on future applications.

Jan 1, 2006

By F. G. Vetsch, F. A. Ronaghan

"Introduction1N THE FALL of 1951, Peace River Allied Fort St. John No. 1 well was drilled in Lsd. 1, Section 9 Township 83, Range 18, West of the 6th Meridian, on the flats of the north side of Peace river, six miles southeast of the village of Fort St. John, B.C. During this operation, non-commercial shows gas in three zones and of oil in one zone were obtained during the drill-stem tests. Further geological study indicated that this well was on the southeastern edge of the Fort St. St. John structure.Pacific Fort St. John No. 4, drilled shortly afterwards, obtained possible commercial gas flows on drill-stem test in five zones and thus encouraged development of what has become Canada's largest multizone gas field.In general, the productive horizons in this area possess fair per-meabilities and high porosities, a combination which provides for high reserves and moderate productivities. Development to date has therefore stressed experimental techniques in drilling and completion practice to provide high deliverability wells.Data and information of a specific nature apply, in all cases, to the pools in the Fort St. John structure."

Jan 1, 1954

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By w. w. Fraser

"In late 1985, Hudson Bay Mining and Smelting Co., Limited announced the Namew Mine/Mill project. Environmental baseline monitoring and planning began in early 1985 while a major drilling program was under way to delineate the ore deposit. This paper overviews the environmental assessment work conducted for the mine/mill operation, and outlines the tailings and water management practices.Planned environmental works and approach were affected in late 1988 when a massive water problem was encountered in the mine. The requirement to depressurize the rock surrounding the underground workings led to the need to develop, on short notice, an environmentally-acceptable procedure to dispose of a large volume of slightly-saline water.Biological toxicity tests performed on the depressurized effluent proved the effluent to be non-toxic and thus allowed resolution of the disposal problem. This resolution includes the conversion of a large water body from native fish species to a rainbow trout fishery."

Jan 1, 1991

By Claudia Gasparrini

"Factors affecting the extraction of gold are of a mineralogical nature. Knowledge of the mineralogy of the ore or metallurgical product to be treated, if appropriately combined with the metallurgical test work, may improve gold recoveries. .This paper outlines the mineralogical techniques f or the study of gold ores and metallurgical products and describes the gold mineralogy in relation to its metallurgy. An effective plan for studying refractory and other difficult ores, combining metallurgical test work, chemical analysis and mineralogy and capable of giving positive results over relatively short periods of time, is suggested.IntroductionFactors affecting gold recoveries are of a mineralogical nature and include (i) the gold-bearing minerals, (ii) their grain size and, particularly where the grain size is very fine (10 microns in diameter and less), (iii) their host minerals and (iv) the association these form with the gold-bearing minerals.Mineralogical studies of gold ores and metallurgical products containing gold in economic amounts (today down to 1/10 of one ounce per tonne or 2.84 ppm) are difficult and time consuming. Mostly because of such reason, metallurgical testing (test work) is usually done simply by trial and error without understanding the causes for failure or success.Mineralogical studies, if appropriately conducted and combined with the test work, provide an efficient mean s of improving recoveries through the understanding of gold losses derived from the use of the wrong technique for separation. The information they provide is therefore the first step in the development of recovery techniques, for those ores where the test work alone failed to produce positive results."

Jan 1, 1983

By O. W. Ellis

Introduction During the month of September, 1928 enough money had. been promised by private individuals and corporations to comply with the Research ?Foundation Act 1928 (Chapter 57, 18 George V) of the Province of Ontario. The Ontario Research Foundation (referred to below as O.R.F.) may be said to 1iave come into being at that time. Under the terms of this Act, the Treasurer of the Province was empowered to match dollar for dollar of the sums subscribed by private .corporations and individuals up to a limit of $1,000,000. However, the response to the appeal for this by the Premier of the Province, the Honourable Mr. G. Howard Ferg uson, was so exceptional that the Act was amended in 1929 so as to empower the Treasurer to increase the maximum contribution on the part of the Province to $2,500,000. In March, 1933, the Chairman of the Foundation, Sir Joseph Flaville, Bart., was able to report that, in the interval between the Premier's appeal and December 1st, 1932, private enterprise had paid ?into the treasury of the Foundation $1,670,050, and that the Provincial Treasurer had assumed responsibility for a like sum. The endownment Fund of the Foundation was, therefore. $3,340,100. This sum was ?invested a lm~ s t entirely in Government securities, in securities guar. anteed by the Government, and in 1mmicipal securities. Sir Joseph Flavelle remarked at that time that "The payment of $1,670,050 to the Endowment of the Foundation by private persons and corporations is a somewhat remarkable performance when it is remembered that for three of the five years the business of the country has been suffering from a severe depression". Since that time it has been the consistent policy of O.R.F. to live within the income derived (1) from the investment of its Endowment Fund and (2) from fees collected for services rendered.

Jan 1, 1950

By C. W. Langenberg, D. E. Macdonald, R. S. Strobl

"The successful marketing of Alberta coals will increasingly depend, to a large degree, on an extensive coal quality information base. This information, at present, is generally based on a deliverable, cleaned coaland is confined to existing mine sites. Coal quality information is not as well understood for raw in situ coal outside of mine sites and even less is known about the geological factors that control it.If new uses and markets for Alberta coal are to be developed, such as gasification, coprocessing, and exploiting high rank coals for combustion, it will be imperative that the coal quality parameters important for these utilizations be known. These parameters need to be known for existing deliverable coals and, just as important, for as yet unexploited in situ coal. Factors such as the Cl, No, K, Co, P and trace element contents should be addressed to meet the requirements of these new utilizations.The geological characterization and explanation of what factors control these coal quality parameters is part of research being done at the Alberta Geological Survey. In-seam vertical profiling has been undertaken within the plains and foothills/mountains coals to determine exactly where coal quality variations occur and why. In the Ardley coal zone at the Highvale Mine it has been found, for example, that the ash content of the mined coal is made up of discrete partings and of microsized particles associated with inertinite macerals. The in-seam characterization of coal seams will lead to a better understanding of in situ coal quality variations, leading to new uses and markets for Alberta coal."

Jan 1, 1993

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By Arthur. H. Winckers, Stephan L. Chryssoulis

"The deportment of gold in residue samples of cyanide leach tests of David Bell ore from level 6A block 13 was established using a comprehensive quantitative mineralogical approach. In every test the feed was first pre-aerated for 4 hours, followed by 48h cyanidation. Test no. 2 was done without lead nitrate and yielded a residue assaying 3.03g Au/t. In test nos. 4 and 9 lead nitrate was added before pre-aeration at 0.03kg/t and 0.3kg/t respectively yielding residues of 1.04 and 0.81 g Au/t.The mineralogical approach employed to establish the deportment of gold involved superpanning, to preconcentrate the free gold and assaying of the tailing fraction to determine the gold associated with quartz. It was thus determined that without lead nitrate added 47.2% of the lost gold is in the form of residual free gold particles less than 20 µm in size. It is this form of gold which is under represented in the residues of leach tests with lead nitrate added.Having eliminated coarseness of gold particles as a factor for lower recovery, it was determined that the residual gold particles have extensively contaminated surfaces. Amongst the deleterious surface contaminants identified: S, As, Ag, Sb and Hg, the two most harmful are S and Hg because of their concentration on the surface and rate of accumulation.Mercury and Ag are minor constituents of native gold at David Bell (average composition Au: 78.9 wt%, Hg: 18.5 wt% and Ag: 2.6 wt%) and they become enriched on the surface of residual gold particles because of their slower rate of dissolution in cyanide. The other elements absorb onto the gold particles from solution.The beneficial effect of lead nitrate was documented by comparative surface analysis of gold from residue samples of 48 hour leach testing with and without lead nitrate added and from time dependent (0-2 hour) leach tests in the presence and absence of lead nitrate. Lead nitrate accelerates the dissolution of gold by performing the following functions: (i) catalytic effect on the cyanidation of gold by accepting electrons; (ii) reaction with surface sulphur to form PbS which is then removed by oxidation; (iii) catalytic reaction on amalgam and Ag facilitating the cyanidation of Hg and Ag thus slowing down their build up onto the dissolving gold particles and (iv) the precipitation of sulphide sulphur from solution thus minimizing its build up on the surface of dissolving gold particles which is believed to facilitate the access of cyanide ions."

Jan 1, 1996

By E. Howard Lambert

"Operating costs of mining plants are increasing due to the increased cost of labour, materials and fuels. Labour and materials costs are factors not readily controlled. However, the use of energy from fuels may be controlled by plant operations. This paper describes the fossil fuels, their expected rate of depletion and their costs. The paper considers methods which may be used to provide an efficient use of energy from fuels. It includes an outline of obtaining energy, as heat, from mine milling operations (air compression) and obtaining the maximum use of energy from fuels used to generate electricity."

Jan 1, 1973

By David S. Robertson, Richard F. Douglas

"Uranium is a lithophile element of relatively low natural abundance. Concentrations of uranium form through processes of erosion and sedimentation, and over 90 per cent of the western world's uranium ore reserves are in sedimentary rocks.Proterozoic quartz-pebble conglomerates contain about 60 per cent of the known uranium reserves. These are all similar in appearance, in mode of distribution and in manner of origin. They carry uranium minerals and/or gold and abundant pyrite. Their unique distribution in Huronian time required a pre-existing crust well enough evolved to have plentiful quartz and abundant gold, uranium and pyrite. The materials of value were deposited as detrital heavy minerals prior to the appearance of an oxidizing atmosphere in late Proterozoic time.Epigenetic uranium deposits occur in arkosic sedimentary rocks through the entire geological column. About 30 per cent of the western world's known ore reserves are in _these rocks. This type of deposit is particularly prominent in semi-arid parts of the United States, having yielded most of the uranium ore produced and containing nearly all of the known reserves.The Western States type"" of deposits occur in lenticular, permeable stream-laid sedimentary rocks. The de-posits are believed to have been precipitated from moving ground water at locations where plant debris or other organic matter had accumulated. The uranium may be derived from volcanic sediments, which are commonly associated with the units containing the ore, or it may be leached from exposed granite surfaces or from granitic debris which forms the sediments.A significant part of the world's uranium resources are in black shales and lignitic rocks. The lignites that contain uranium are virtually valueless as potential sources of heat. Uranium concentrations at levels such as to be potential sources of by-product uranium occur in many phosphorites.Reworked sediments may provide uranium in pegmatites and vein-like deposits."

Jan 1, 1970

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By Brandt Porter, Lawrence K. Nordell, Alexander Potapor

"Improving comminution efficiencies with better machine geometries and motions, improved nip angles, rock movement control, and voids regulation among rocks are some of the next steps to better machine performance. Recent gains (~30%) using high pressure grinding rolls (HPGRS) and vertical roller mills, in theory and practice, are based on Prof. Klaus Schönert’s academic studies (1979–1996) on rock breakage physics. More recently, University of British Columbia Prof. Bern Klein’s studies (2006–present) via the Ph.D. thesis of Z. Davaanyam (2015) further validate theory with practice from laboratory measurements used in this paper.They demonstrated ideal rock compression breakage, within HPGR and vertical roller mill machines using a piston-die apparatus. Similar rock size range is used. The piston-die confine rock breakage behavior. However, these studies do not extend to larger rocks (> 75 mm), and do not demonstrate the influence of rock voids among bifurcation of rocks during comminution. Further, machines fed with larger rock sizes, such as gyratory, jaw, and cone crushers, are not designed or evaluated for geometry nip angle efficiency.Herein we illustrate a performance gain of a new comminution machine, the conjugate anvil-hammer mill (CAHM), first presented at SAG 2011 (Nordell, 2012). The CAHM machine digests rock sizes 400% larger than HPGR, improves rock grip/nip geometry, better improves rock voids, improves surface wear life > 500%, and improves rock containment and slippage during compression. In all, the CAHM machine shows 22 potential improvements over the HPGR. Most importantly, CAHM shows a 50% kWh/ton improvement compared to the HPGR. Our studies use an advanced Discrete Element Method (DEM) computer program called ROCKY. ROCKY simulates moving boundaries, surface wear mechanics, and incorporates rock breakage physics based on the fundamentals of JKMRC T10 protocol [×] with tuned A × b breakage parameters.We calibrate rock breakage in our DEM code to mimicking both UBC laboratory piston-die and HPGR comminution measurements. We then model CAHM with these known ore and machine properties. Differences are illustrated using DEM techniques on each machine, including key points of when each: use geometry; initiate bifurcation breakage; provide a map of particle size distribution by location; illustrate the importance of controlling voids to minimize agglomeration after breakage; machine performance limits; and kWh/ton benefit."

Jan 1, 2016