Search Documents

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By A. D. Misener

Introduction Temperature gradients have been determined for numerous locations in the Canadian Shield in connection with mining operations (1, 2, 12, 13, 14, 15). As part of a programme of geophysical studies of this region, some of these gradients were re-determined by the writer at locations where other thermal properties, specific heat, thermal conductivity, radioactivity, etc., were also to be measured. The ultimate object was to determine the heat flow to the surface at these locations. It was felt that the practice of determining heat flow from the temperatures and conductivities obtained in a single vertical bore hole (3, 4, 5, 6, 7, 8, 9) might give results which were appreciably divergent from the average for a considerable area. Particularly, it was thought that temperature gradients, whether obtained in a single vertical hole or from a number of random locations at various depths in a mine, might be subject to local variations and anomalies serious enough to render unsure any discussions based on them. The procedure followed in this investigation was to select a location where mine workings extended to considerable depth over a reasonably wide area. At selected depths below surface, horizontal drill holes extending into regions of undisturbed rock were located and resistance thermometers were inserted into these holes far enough to record the true rock temperature. An attempt was made to obtain a sufficient number of readings at or near any one level to give a representative coverage of the area selected. This ideal could not always be attained, but the large number of readings obtained for each are a does give a reasonably representative picture of the temperature conditions. These readings required much rime and movement of men and equipment underground . They could not have been obtained without the wholehearted co-operation of the management and considerable assistance from the personnel of the mines concerned.

Jan 1, 1949

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By Neil Camarta

$6 Billion Dollar Education ?? Construction is like war ? you need a command and control organization ?? A strong Owner?s team is a must ?? Smaller is better ? break the project into bite size chunks ?? New technology is risky ? lots of construction and start-up risk ?? Safety can be successfully managed ?? Don?t expect contractors to ?work well together? ?? Never, ever let Mining Engineers run stuff than can catch fire

May 1, 2008

By George P. Demopoulos

For more than 20 years the author had the privilege of working closely on a number of R&D projects with Lucy Rosato and her team at CEZinc. Several of these projects were driven from the sustainability agenda that Lucy Rosato championed as an innovation leader that supported research collaborations. Highlights from this highly rewarding collaboration are to be presented in this paper. In particular we will deal with the following works-topics: (a) iron control via solvent extraction as alternative to jarosite precipitation; (b) production of high-density gypsum by controlled neutralization of simulated zinc plant process/waste waters; (c) selenium removal from weak acid solutions; (d) electrolyte purification by cementation; and (e) manganese control by oxidative precipitation with SO2/O2.

Jan 1, 2015

By B. R. Conard

Copper refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because Cu and Ni carry risks for adverse health endpoints through inhalation exposure, it is critical that their aerosol levels, and the metallurgical processes through which they enter the air, are understood. Because certain Ni substances have been linked to respiratory cancers, it is also important to characterize the amounts and types of Ni compounds in occupational settings. This paper describes electrorefining and electrowinning operations near Sudbury, Ontario (1930–present), and gives aerosol measurements (1978–present).

Jan 1, 2014

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By Barry D. Simmons

Abstract -A well-defined approach is essential to ensure the long-term success of a regional exploration program. Teck's approach in eastern Canada is designed to fulfill corporate objectives while recognizing certain unique parameters for exploration in the area. The elements of this approach include clearly defined objectives, technical considerations and personnel policies, all of which are equally important. The goal is a significant discovery before the mid-1990s and the company is confident that this target will be achieved.

Jan 1, 1992

By Gilles Tremblay

The legacy of orphaned/abandoned mines, with their associated environmental liability, human health concerns and the financial costs of clean up is a serious issue facing Canada. In 1999 and 2000, a number of stakeholders put forth requests to Mines Ministers to establish a joint industry-government working group, assisted by other stakeholders to review the issue of abandoned mines. The Ministers supported this initiative and asked that a multi-stakeholder workshop be organized to identify key issues and priorities. The Workshop on Abandoned Mines, held June 2001 in Winnipeg, developed consensus, guiding principles and recommendations that were presented at the Mines Ministers? Conference, September 2001. Ministers agreed on the importance of a large-scale program for the rehabilitation of orphaned/abandoned mines sites. A multi-stakeholder Orphaned/Abandoned (O/A) Mines Advisory Committee was formed and a plan was developed to study various issues relating to the implementation of remediation programs across Canada. Three task groups were formed to address the following key areas: Information Gathering; Community Involvement; and Barriers to Collaboration. The presentation will include a summary of the results of the three projects and the future work plan for the program.

Nov 1, 2002

By T. Majcherczyk

Shaft lining reinforcing analysis of two shafts under construction has been presented in this study. The first shaft was driven from the surface, while the second was deepened. Mining and geological conditions have been studied with respect to the lining capacity. The improvement of shaft stability comprised two elements, i.e. reinforcement of the shaft lining capacity and improvement of the strength properties of the rock mass. In both tested cases, the particular hazard was connected with non uniform loadings of the lining, which could generate shearing stresses within lining structure. Thus such elements as armored concrete with high strength properties, bolting and injection sealing of the rock mass, and the use of special ring reinforcing the shaft lining have been used in order to reinforce the shaft-rock mass system. Practical conclusions related with new technological solutions, allowing the rock mass and shaft lining reinforcement, have been included for the present study. Practical conclusions related with new technological solutions, allowing for rock mass and shaft lining reinforcement, have been also included to the present study.

Aug 1, 2013

By Omero Alonso-Gonzalez, Sergio Haro-Rodriguez, Ricardo Solis-Rodriguez, Francisco Alvarado-Hernandez, Juan Antonio Gonzalez-Anaya, Héctor Rene Vega-Carrillo

"Precious metals are currently associated with refractory minerals such as telluride (Calaverite, Sylvanite, etc.) and selenium (Naumannite Ag2Se), which are difficult to dissolve through traditional methods, therefore it is necessary to perform a pretreatment (oxidative or roasting) preceding the process of leaching by cyanidation. In this preliminary work the aim was to study the use of solvent extraction to remove tellurium and selenium ions from a synthetic cyanidation effluent, with the purpose of recycling the cyanide back to the process. For the extraction of these anions, TeO32- and SeO42-, tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (Amine F) were studied as extractants, using nonylphenol as a modifier in the organic phase (trimethylpentane). The results show that it is possible to recover 82% of selenium and 10% of tellurium from synthetic solutions containing either 20 mg/L Se or 20 mg/L of Te, respectively The Se or Te mole ratio to cyanide was 1:4.INTRODUCTION In relation to extraction of precious metals, the cyanidation process has been in use for over a century and despite environmental and toxicological problems it remains the most widely used and economical process available. In the late 90s, there were great efforts to recover gold and silver from refractory ores, which is difficult to do by simple cyanidation. To improve gold recovery from tellurides and selenides that occurs in some new mines, the ores are pretreated by roasting. This is one of the most effective ways of rendering refractory gold ores leachable as well as being a fast pretreatment process compared with bio-oxidation or pressure leaching (Aylmore, 2001). The most important tellurides minerals are Calaverite (AuTe2) and, Silvanite (Au, Ag)2Te4). In the case of selenides, minerals include Naumannite (Ag2Se) and Aguilarite (Ag4SeS) (Ostroumov et al., 1989). Examples of deposits containing telluride include La Bambolla Mine (Sonora, Mexico), Cripple Greek (Colorado, USA), and Kalgoorlie (Western Australia) (Aguayo et al., 1996). The main purpose of this work was to explore the feasibility of using quaternary ammonium salts such as: tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (amine F) to extract tellurium and selenium anions from aqueous synthetic cyanidation effluents, so that the cyanide solution could be recycled back to leaching process. The tests were performed on synthetic solutions similar to those found in a mine: 20 mg/L Te as TeO32-, 20 mg/L Se as SeO42- and mole ratio to cyanide was 1:4. using an alkaline medium with pH ranging from 8 to 12. Two aspects are evaluated in this paper:"

Jan 1, 2017

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By Harry F. Weaver

WHEN 1 was assigned by the Director of the United States Bureau of Mines to present a paper at this annual meeting of the Mining Society of Nova Scotia, 1 was grateful, honoured, and elated to realize finally a life-long desire to see your beautiful land and visit with you who have the good fortune to live and work here. Naturally, in preparing for this important event, 1 wanted to give you something of special interest within the limits of the subject so I chose an area dose to my heart -the operation of our Federal coal mine inspection service, which has, as its fundamental purpose, the prevention of accidents in and around ?Coal mines. In 1957 the United States had 10,879 active coal mines scattered throughout 28 States and the Territory of Alaska. The production of coal for the year was about 515,472,000 tons, including 2.5,472,000 tons of anthracite and 490,000,000 tons of bituminous coal and Hgnite. Anthracite is mined principally in a comparatively small area of one State. AU the 28 States and the Territory produce bituminons coal and/or lignite. The beds mined range from 18 inches to more than 100 feet in thickness and from the horizontal to the perpendicular.

Jan 1, 1958

By E. Lee Cameron

Summary Records of the past show that the first mineral production in what is now the Province of Manitoba consisted of salt, obtained about the year 1800 by the evaporation of brine. Also at an early time in our history, the Ordovician limestone at St. Andrews Locks, East Selkirk, and other localities was quarried for use as building scone in the construction of forts and fur trading posts. Both salt and building stone are still produced in Manitoba, although not from the original sources. In addition, there is now a substantial production of a variety of other industrial minerals and their products such as lime, crushed stone, gypsum, peat moss, and bentonite. The annual dollar value of production of the industrial mineral industry in Manitoba is today greater than at any time in our past and is derived from a greater variety of products. At the present time, exclusive of the various gravel pits operated by the Provincial Department of Public Works, twenty companies operating thirty-four separate pits, quarries, or mines are producing industrial mineral raw materials in Manitoba. This paper attempts to outline the development of the industry from its start about 1800 to the present, giving general information on the various materials produced. Some suggestions regarding the possibilities of establishing new industries based on other raw materials are given at the end of the paper.

Jan 1, 1949

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By B. J. Walsh

ABSTRACT Segregation of sphalerite minerals in zinc concentrates into christophite, marmatite and ordinary sphalerite by means of magnetic fractionation is investigated. A Frantz ferromagnetic filter, 1.2 amp., and a Dings magnet, 0.3 amp., is used to fractionate seven zinc concentrates produced in the Province of Quebec. The Dings magnetic product contains the pyrrhotite, and the sphalerite as christophite. The Frantz magnetic product contains sphalerite as marmatite, while the Frantz nonmagnetic product contains ordinary sphalerite. The results indicate that the magnetic susceptibility of sphalerite increases with increasing isomorphous iron content and that a satisfactory separation into christophite, marmaite, and ordinary sphalerite may be accomplished by magnetic fractionation. INTRODUCTION SPHALERITE, the chief ore of zinc, is almost never pure zinc sulphide. Iron is almost always present isomorphously replacing an ?equivalent amount of zinc. What may be referred to as 'ordinary' sphalerite contains up to 10 per cent iron. More highly ferriferous varieties, with 10 to 26 per cent or more iron, have been named marmatite .and christophite.

Jan 1, 1951